ArchiveThe time-frequency electromagnetic method (TFEM) represents an artificial-source electromagnetic survey technology developed by integrating the advantages of both the frequency-domain controlled-source electromagnetic (FD-CSEM) method and the transient electromagnetic (TEM) method. This technology enables simultaneous acquisition of time-domain and frequency-domain electromagnetic responses with a single excitation. It is characterized by large exploration depths, multi-parameter inversion, high signal-to-noise ratio, and strong anti-interference capability, providing technical support for the fine characterization of subsurface structures. This study presents a systematic review of the TEFM, covering its core technical architecture and the equipment development roadmaps in China and abroad, with a particular emphasis on the analysis of the theoretical models, application status, and technical bottlenecks of the TFEM in three major fields, i.e., hydrocarbon exploration, mineral exploration, and geothermal resource surveys. The results of this study indicate that the TFEM effectively overcomes the limitations of traditional electromagnetic methods in exploration depth and parameter dimensionality, thus fully satisfying the high-precision and large-depth requirements of current energy resource exploration. However, its application in mineral and geothermal fields is in a critical stage of large-scale expansion, with its potential yet to be fully tapped. In the future, the TFEM technology will be expanded into fields such as ground-air collaborative detection and 3D/4D time-lapse monitoring, accompanied by constant innovations in multi-physics coupling and intelligent inversion algorithms. These advances will provide new impetus for its industrial application and technological upgrade.
The Lala copper deposit in Sichuan Province is characterized by a thick low-resistivity cover, a great burial depth, and thin ore layers. By comparing the differences in the applicability of the time-frequency electromagnetic method (TFEM) and the audio magnetotelluric method (AMT) to deep copper exploration in this deposit, this study aims to address the issue of insufficient accuracy in the identification of deep targets. The TFEM and AMT methods were applied to the study area for tests. The comparison of the test results with existing drilling data revealed that the TFEM method exhibited a higher resolution than the AMT method and effectively identified the positions of ore layers or zone-bearing layers. These characteristics establish the TFEM method as a preferred approach for the detailed survey of key target areas. Nevertheless, the AMT method remains cost-effective for preliminary exploration of shallow structures. This study offers a valuable case for enriching geophysical methods for deep ore exploration in the study area.
The Jinchanghe ore concentration area in the Baoshan block, Yunnan Province, is located in the northern part of the Baoshan-Zhenkang lead-zinc-copper polymetallic metallogenic belt. This area primarily hosts skarn iron-copper-lead-zinc polymetallic deposits. Previously, strong magnetic anomalies served as the primary geophysical exploration indicators for mineral prospecting in this area, while weak magnetic anomalies gained insufficient attention. Therefore, this study investigated weak magnetic anomalies in this area to reveal their promising potential for mineral prospecting. The time-frequency electromagnetic method and the high-precision magnetic survey were combined to verify weak magnetic anomalies, obtaining information on electrical and magnetic anomalies. Based on geological conditions, the joint inversion of multiple parameters was performed to delineate prospecting targets and precisely determine the spatial morphologies and occurrence locations of deep concealed ore bodies. Through borehole verification, the combined method achieved significant prospecting results. This study serves as an exemplary case for mineral prospecting in the deep and marginal parts of this area and also a reference for the exploration of similar deposits in other areas.
The time-frequency electromagnetic (TFEM) method, a new electromagnetic exploration technique, emerged at the beginning of this century, followed by its introduction and development in the hydrocarbon exploration field. It combines the advantages of both frequency-domain and time-domain electromagnetic techniques, offering a higher resolution and more accurate imaging of underground structures under complex geological conditions. It plays an important role in energy resources exploration. This paper presented the application of the TFEM method in the hydrocarbon exploration in the Niutuozhen uplift. The results indicate that the hydrocarbon reservoirs in this uplift exhibited low-resistance and high-polarization electromagnetic response from the upper layers. Conversely, they showed the high-resistance and high-polarization electromagnetic response from the internal. Based on the TFEM abnormal response patterns, five play fairways were delineated in the Niutuozhen uplift, which were basically consistent with known drilling data. This study provides a solid foundation for the hydrocarbon development and utilization in this area.
The Yamenzi area is located within the Yanshan-Liaoning metallogenic belt in the middle segment along the northern margin of the North China plate. This metallogenic belt serves as an important one for nonferrous and precious metals in China, characterized by favorable geological conditions for volcanic to subvolcanic silver-polymetallic ores. To further optimize targets and evaluate their potential for ore prospecting, this study conducted a 1∶10,000 soil geochemical survey in the Yamenzi area. By analyzing mathematical statistics and delineating anomaly contrasts of the 12 testing elements, silver (Ag), lead (Pb), zinc (Zn), and gold (Au) were identified as the primary metallogenic elements of the area. Based on the metallogenic geological setting and the coincidence of element anomalies, five prospecting targets were identified. Subsequently, these targets were verified by trenching and drilling engineering, revealing multiple Ag-Pb-Zn orebodies. A comprehensive comparison revealed similar patterns of Ag-Pb-Zn metallogenic belts between the Yamenzi in Hebei and Zhijiadi in Shanxi. Therefore, further investigating metallogenic regularity within the Yamenzi area could potentially guide the discovery of larger-scale orebodies.
The Foping area, a geological dome in southern Shaanxi Province, has long been a geothermal blank zone. To explore the deep structural characteristics and stratigraphic configurations of the dome and preliminarily delineate the accumulation range of geothermal water, this study arranged the wide-field electromagnetic method (WFEM) and soil radon measurement profiles in the Foping area. Through field data collection, processing, and inversion, the electrical structural characteristics of the Foping area within a burial depth of 4 000 m were obtained. A new understanding was proposed accordingly: the Foping area develops multiple nappes from northwest to southeast, with the northern and southern sections dominated by thrusting and gliding, respectively. Its overall structural style is manifested as an antiform centered around Foping County. A continuous low-resistivity anomaly zone, occurring in the deep part, is associated with the roof detachment fault and the fracture zones formed in the central and lateral parts during rock intrusion. These faults create conditions for the downward migration and storage of groundwater. The superposition of thrusting rock fragments has led to well-developed fractures between rock fragments and pores, vugs, and fractures in brittle rocks such as marbles and quartzites, constituting the space for the occurrence of geothermal water. Based on objective factors such as local industrial planning, economic development, and road conditions, drilling work was conducted in Jiaochangba Village, Changjiaoba Town, 2.5 km north of Foping County, along the west bank of the Jiaoxi River. The completed well reached a depth of 2 002 m, producing geothermal water with a temperature of 35 ℃ at a flow rate of 392 m3/d. This achievement breaks through the traditional concept that the Foping dome contains no or little water. Therefore, this study provides actual data for exploring the geological structural characteristics and hydrogeological conditions in the Foping area, as well as a reliable basis for basic geological theory research.
Near-surface layers are typically characterized by loose structures and significant vertical and lateral variations in both thickness and velocity. These characteristics result in marked absorption of seismic wave energy and severe phase distortion, substantially reducing the signal-to-noise ratio (SNR) and resolution of acquired seismic records. The absorption properties of these layers can be described by the quality factor (Q-value). Given the complex structures of near-surface layers, constructing a precise quality factor field requires simultaneous consideration of their pronounced vertical and lateral variations. This study first summarized an optimization strategy for quality factor inversion based on data from uphole surveys by analyzing the applicability of common Q-value inversion methods. To further enhance the accuracy of near-surface quality factor field modeling, this study proposed a method for constructing precise quality factor field models. This method integrates high-resolution information from uphole survey data with high sampling-rate information from reflection wave data. Tests on real data demonstrate that the proposed method effectively captures detailed variations in lateral Q-values of the layers. The compensated seismic waves exhibited broadened effective frequency bands and significantly improved seismic resolution, thereby validating the effectiveness of the presented approach.
In the monitoring of geologic CO2 sequestration, time-lapse seismic data can capture the CO2 injection-induced subtle changes in CO2 saturation and associated reservoir physical properties, which are crucial for evaluating the storage safety and effectiveness. Although conventional full-waveform inversion can exploit full-waveform information in time-lapse seismic data, it is highly nonlinear and strongly dependent on the initial model and low-frequency components, rendering it prone to cycle skipping. Hence, this study incorporated wavefield reconstruction inversion (WRI) into time-lapse seismic inversion, combined with parallel and double-difference inversion strategies, to establish an inversion process for monitoring geologic CO2 sequestration. Model test results show that the WRI, based on the parallel inversion strategy, effectively suppressed artifacts while also recovering the geometric morphologies of velocity-change zones. The double-difference inversion strategy further enhanced inversion stability. The WRI, based on the double-difference strategy, accurately captured velocity perturbations in both strong and weak velocity-change zones, yielding significantly reduced artifacts and outperforming conventional methods in both boundary clarity and amplitude recovery. Overall, this inversion method improves the inversion accuracy of the target area while also enhancing the identifiability of reservoir changes, serving as a robust and reliable technical approach for 4D seismic monitoring of geologic CO2 sequestration.
The microtremor surface waves collected from karst areas, where near-surface conditions are complex, often show low signal-to-noise ratios (SNRs) and poor data quality, thus restricting the detection accuracy. Hence, this study proposed a microtremor surface wave imaging method based on singular value decomposition (SVD). First, the single-trace virtual-source empirical Green's function obtained by cross-correlation was reconstructed through SVD. The signal components corresponding to large singular values were extracted to reconstruct the wave field, thereby effectively suppressing the noise and improving the SNRs of surface waves. Second, the virtual-source multi-trace records were constructed using the reconstructed signal with high SNRs. The dispersion energy spectrum was derived through the F-K transform, obtaining significantly improved surface wave dispersion bands in terms of resolution and continuity. Third, the frequency dispersion curves were extracted from the optimized dispersion energy spectrum. The joint inversion strategy employing the genetic algorithm and damped least squares was used to further improve the imaging accuracy, considering the globally optimal solution and convergence efficiency. Fourth, by integrating the inversion results of all survey points in the study area, a two-dimensional shear wave velocity profile was constructed to reveal the underground structural characteristics and the spatial distribution of karsts in the study area. The practical application in a karst area demonstrates that the proposed method can effectively improve the imaging quality of the karst area with complex near-surface conditions, providing reliable technical support for the fine-scale structure detection and geological interpretation in karst areas.
Performing various corrections to the measured gravity values relative to a datum plane serves as a necessary step in obtaining the values of Bouguer gravity anomalies. Currently, the various corrections of large-scale gravity survey data primarily follow the requirements and methods of regional gravity surveys. The obtained Bouguer gravity anomalies often contain false anomalies, failing to accurately interpret the relevant properties and details of targets. Moreover, there exists neither systematic research on the variable-density terrain correction for large-scale gravity survey data nor publicly available variable-density correction calculation software. Therefore, this study proposed a set of fine-scale correction methods for large-scale gravity survey data. Specifically, the traditional datum plane for various corrections was elevated. Based on the rating of density property data, the variable-density generalized terrain correction method was employed to integrally calculate the values of traditional terrain and intermediate layer corrections. The Li-Gotze96 equation was applied to integrally calculate the values of traditional latitude and height corrections, as well as the height correction value based on the custom datum plane. A new equation for calculating the value of Bouguer gravity anomalies was derived. Moreover, the universal gravity survey correction calculation software was developed accordingly. The verification based on simulated and measured data shows that these methods can significantly reduce false anomalies within the Bouguer gravity anomalies and their association with terrains, thereby highlighting the anomaly characteristics of the targets and revealing richer anomaly details.
Porosity serves as a crucial reservoir parameter for hydrocarbon exploration. This study constructed a mathematical model integrating Gassmann's equation and Eshelby-Walsh theory. Using this model, an objective function was derived and established for direct porosity inversion relying on the inverted high-precision pre-stack elastic parameters from pre-stack seismic data with a high signal-to-noise ratio, thereby enabling the direct calculation of formation rock porosity. Within the framework of generalized linear inversion theory, using the precise Zoeppritz equation as the theoretical foundation, this study achieved the direct inversion of reservoir porosity by introducing well-logging data as constraints. Conventional porosity estimation methods rely on the indirect porosity estimation using parameters such as P- and S-wave velocities and density, resulting in multi-step error accumulation. To overcome this limitation, this proposed method allows direct input of seismic gathers and well-logging data. In addition, grounded on the theoretical advantages of the exact Zoeppritz equation in describing wavefield propagation, this method yielded inverted porosity results with higher resolution and accuracy compared to those obtained using conventional methods based on three-parameter empirical conversions. Application in actual data shows that the porosity data obtained from the well-logging constrained direct inversion of pre-stack elastic parameters align well with actual logging curves, demonstrating higher accuracy and resolution. The high-precision porosity data provide critical theoretical value and practical guidance for detailed reservoir prediction, well placement optimization, and the design of fracturing production schemes.
Shear wave velocity serves as a key parameter for characterizing the elastic properties of rocks and their sensitivity to fluids, playing a significant role in seismic wave impedance inversion, stratigraphic identification, and rock physics modeling. However, the limitations in acquisition costs and technologies often lead to data gaps or insufficient accuracy for shear wave velocity. Hence, this study proposed an intelligent method for predicting shear wave velocity by integrating the two-dimensional convolutional neural network (2DCNN), a state-space model, and a cross-attention mechanism. The 2DCNN and the state-space model can capture local spatial features and longitudinal temporal dependencies, respectively, while the cross-attention mechanism enables the deep fusion of spatial and temporal features, thereby enhancing the sensitivity of the network to key geological information. Additionally, to improve model explainability, an explanatory analysis method based on Shapley additive explanations (SHAP) was employed to quantify the contributions of different log parameters to the shear wave velocity prediction. Experimental results demonstrate that the proposed method outperformed traditional individual neural networks in both prediction accuracy and generalization capability. Moreover, it effectively revealed the physical relationships between shear wave velocity and conventional log parameters. Therefore, the proposed method provides a novel approach and technical support for rapidly and reliably predicting shear wave velocity under complex reservoir conditions.
Flexure structures are highly hazardous geological structures in underground coal mines. Their accurate identification and characterization have long been a technical challenge in the geological guarantee of the mines. Conventional seismic exploration methods struggle to achieve fine-scale identification of flexure structures due to their limitations in resolution and signal-to-noise ratio. In contrast, fully digital high-density 3D seismic exploration technology, characterized by wide frequency bands, wide azimuths, and high coverage frequency, can provide high-quality data for fine-scale interpretation of flexure structures. This study investigated a block in the Yangquan mining area. Using the fully digital, high-density 3D seismic exploration data, this study proposed and systematically implemented an offset vector tile (OVT)-domain split-offset coherence cube fusion technique. Specifically, the seismic data were classified into far-, moderate-, and near-offset intervals in the OVT domain. The coherence cubes in the three intervals were computed using the third-generation coherence (C3) algorithm. Furthermore, the attribute fusion technique was employed to integrate the split-offset coherence cube slices into a comprehensive coherence cube slice, enabling fine-scale characterization of the main flexure zone and other concealed structures within the study area. The results demonstrate that the identified flexure structures based on the proposed technique align with the actual wellbore exposures. By leveraging the rich azimuth and offset information in wide-azimuth seismic data, the proposed technique can effectively overcome the limitations of individual coherence cubes in terms of the multiplicity of solutions and resolution. Furthermore, by complementing and integrating seismic response characteristics across different offsets, this technique can significantly enhance the capability for fine-scale identification of flexure structures. Therefore, this study provides an effective technical approach for achieving transparent detection of concealed geological hazards in coal mines.
Porosity is a critical parameter for characterizing reservoir physical properties. The accuracy of porosity prediction holds significant implications for hydrocarbon exploration and production, as well as the geological modeling and fine-scale evaluation of hydrocarbon reservoirs. Considering the characteristics of tight sandstone reservoirs, such as low porosity, low permeability, and strong heterogeneity, this study proposed a reservoir porosity prediction model that integrates the convolutional neural network (CNN) and bidirectional long short-term memory(BiLSTM). The CNN-BiLSTM model is used to extract features from log data and establish complex nonlinear correlations between these features and porosity parameters. First, using petrophysical models, sensitive elastic parameters, which are significantly correlated with porosity, are selected as input parameters. Second, the spatially dependent features are extracted from the inversion data using the CNN. Third, the temporal dependencies throughout the data sequence are captured by BiLSTM. These processes contribute to effective porosity prediction. The test results of three wells in oilfield A, Kaiping sag, demonstrate that compared to conventional deep learning methods, the CNN-BiLSTM model achieved higher accuracy and lateral resolution in porosity prediction, verifying its effectiveness. Furthermore, the CNN-BiLSTM model was applied for the 3D reservoir porosity prediction by calculating the porosity data volume from elastic parameter volumes obtained through reservoir inversion. Overall, this study provides a novel approach for predicting reservoir porosity in the sparse well area of oilfield A, offshore Kaiping sag.
In potential field exploration, the Euler deconvolution method has been extensively utilized due to its minimal requirement for prior information. However, it yields significant dispersed results due to external interference. Based on a further investigation of the Euler deconvolution method, this study proposed a simple, effective finite-difference Euler deconvolution method for determining the depth and structural index of field sources. The proposed method leveraged the linear relationship between depth and structural index in the Euler equation. Combining data from multiple continuation heights at potential field source locations, a system of equations was constructed using the finite difference method to solve for coefficients, thereby determining the depth and structural index of field sources. The inversion was limited to potential horizontal locations of field sources, effectively reducing the number of inversion results. Additionally, the strategy of combining data from different heights for inversion mitigated the impacts of noise and other disturbances. Finally, the proposed method proved effective through model experiments and actual data.
The clay-type lithium ores, a significant lithium resource in China, contain lithium and other elements such as aluminum and silicon. Their molecular formulas are expressed as LiAl [SinO2n+2] and Li [AlSinO2n+2] in this study. The latter formula represents the ion-absorbed lithium ores, from which lithium ions can be readily extracted in leaching experiments. This study explores an environment-friendly, economical, normal-temperature in situ leaching technique for clay-type lithium ores, which requires that the chemical properties of lithium ores remain unchanged before leaching experiments. The contents of various elements, loss on ignition, and porosity (massive ores) of clay-type lithium ores were analyzed through the column leaching experiments. Three leaching reagents were used: 10% sulfuric acid solution, 10% ammonium sulfate solution, and a mixture of 5% sulfuric acid solution and 5% ammonium sulfate solution. The total leaching process lasted for 190 d. The concentrations of lithium and aluminum were determined at regular intervals. The experimental results show that the porosities of the clay-type lithium ores ranged from 0.38% to 6.20%. The first and third reagents demonstrated higher leaching efficiency, achieving a Li2O leaching rate of up to 0.56% without refilling fresh reagents, whereas the leaching efficiency of the second reagent was not satisfactory. Notably, in the case of a reduced ore size, the third mixed leaching solution yielded the same leaching efficiency as the first high-concentration sulfuric acid solution. Overall, this study provides a practical in situ leaching technique for clay-type lithium ores in mines.
The ocean bottom node (OBN) boasts the advantages of more flexible deployment, better seabed coupling, and higher signal-to-noise ratio (SNR). However, the non-real-time acquisition mode also raises many challenges for quality control. These include cumbersome verification of the OBN clock drift correction accuracy, as well as a lack of methods for accurately verifying the rotation accuracy of three-component geophone data after vector rotation and the OBN positioning accuracy after underwater towing events. This study extracted the information on near-offset first breaks from the OBN data to generate a four-component amplitude diagram through appropriate arrangement and difference calculation. By investigating the amplitude attributes under different conditions, targeted quality control was achieved. This method demonstrated excellent quality control effects in practical applications, making it an important tool for quality control in OBN acquisition.
Scholte waves serve as surface waves propagating at a fluid-solid interface, carrying abundant seabed information. They exhibit dispersion during propagation, which is primarily controlled by the parameters of both seawater and seabed. To investigate the influence of different marine environments on Scholte waves, this study first derived the equation expressing their dispersion characteristics based on a layered seabed model. Then, using the staggered-grid finite-difference (SGFD) method, it conducted forward modeling on several typical marine models. The dispersion characteristics of the theoretical Scholte wavefields were analyzed using the cross-correlation and phase-shifting (CCPS) method. The analysis results show that the dispersion characteristics of Scholte waves weakened with increased seawater depth. In addition, Scholte waves are highly sensitive to changes in the S-wave velocity of the medium that, in turn, exert a significant impact on the dispersion characteristics of Scholte waves. In the case of decreased S-wave velocity of the solid medium layers, the Scholte waves exhibited stronger dispersion, accompanied by significant changes in both energy and dispersion curves.
Waveform inversion refers to the process of inferring underground medium parameters using seismic wave data. For elastic media, the interdependency between P- and S-wave velocities and density parameters enhances the nonlinearity of multi-parameter waveform inversion, leading to crosstalk in the inversion results. Given this, this study proposed an automatic differentiation-based multi-parameter full waveform inversion method for elastic media constrained by nonlinear anisotropic diffusion regularization (NADR). To address the strong parameter coupling and high nonlinearity in multi-parameter inversion, this study added an anisotropic diffusion regularization term to the objective function. Then, it calculated gradients using automatic differentiation technology, followed by iterative optimization using a mini-batch strategy. Experimental results show that the NADR can effectively mitigate parameter crosstalk and improve the inversion stability.
Soil organic matter (SOM) plays a crucial role in the global carbon cycle. Through statistical analysis and correlation analysis, this paper investigated the SOM content and its influencing factors for 105 groups of surface soil samples from the Hongwei-Daxing farms in the northeastern Sanjiang Plain. The results show that the SOM exhibited a content in the study area ranging from 1.72% to 13.80% (average: 4.78%) and significant enrichment in surface soil, with an enrichment coefficient of up to 10.29. The SOM content generally followed a normal pattern in its frequency distribution and an obvious regional pattern in its spatial distribution, with significantly higher SOM observed in the northeast than in the northwest of the study area. In typical soil profiles, both SOM and total nitrogen (TN) content showed a declining trend with the increase of soil depth, suggesting SOM aggregation in the surface soil layer. Meanwhile, the SOM content was positively correlated with some soil physiochemical indicators, such as moisture content, clay particle content, water-stable aggregates, iron oxide (Fe2O3), and TN, which represent favorable factors for SOM accumulation in the study area. In contrast, the SOM content exhibited negative correlations with the bulk density, pH value, and potassium oxide (K2O). Moreover, the variations in soil carbon pools were quantitatively evaluated after the conversion of wetlands to croplands. The results indicate that the average SOM content followed the order of wetlands (8.87%) > dry lands (5.90%) > paddy fields (4.21%). Furthermore, the conversion resulted in a significant increase in soil pH and losses of SOM, TN, and total phosphorus (TP) to varying degrees. Among various soil types, boggy soil exhibited the highest average SOM content of 6.77%, representing a favorable factor for SOM accumulation in the study area. Among various parent materials, the Quaternary high-magnitude floodplain sediments presented the maximum average SOM content in the generated soil. This is attributed to their predominant composition: lacustrine mucky clays and loams, whose high content of clay particles favors SOM accumulation. These findings provide a scientific basis for enhancing the management and sustainable utilization of land resources, wetland protection, and the carbon sequestration function of the area.
The compression and settlement of waste deposits in landfills may cause the deformation failure of leachate collection pipelines in municipal solid waste treatment facilities. This failure will further lead to the rupture of the impermeable layers and subsequent leakage of landfill leachates. Primary methods for monitoring damage to leachate impermeable layers include: laboratory chemical analysis of the pollutant levels of soil and water samples from landfills, and surface geophysical exploration. Building upon the above traditional environmental geological exploration methods, this study achieved effective prediction of landfill leachate leakage using geographic information system (GIS) technology combined with machine learning and influencing factor prediction. Specifically, the landfill area was divided into grid cells with resolution of 5 m × 5 m, which were then assigned corresponding spatial coordinates. A machine learning approach was employed to establish artificial neural network (ANN) models for predicting landfill leakage points. Based on a field investigation of a landfill in North China, 880 test samples and 220 validation samples were selected. The data obtained from these samples, including groundwater table depth, resistivity, polarizability, anomalies of seismic events in radar reflection waveforms, spatial relationships between seismic events and adjacent monitoring boreholes, and half-life information, were used as the input for the models. The output provided the leakage probabilities of all grid cells. Finally, the prediction results of two machine learning methods, the backpropagation (BP) and radial basis function (RBF) neural networks, were comparatively analyzed. The findings indicate that the BP neural network model showed higher prediction performance. The groundwater table depth, resistivity, and the relationship between resistivity and monitoring borehole positions served as the dominant factors influencing the seepage probability prediction of the impermeable layer. By superimposing the posterior probabilities of various influencing factors, the prediction model generated a classification map for leakage risk zones, achieving the objective of graded monitoring of leachate leakage risks within the landfill area.
Leakage hazards in dikes are recognized as a core issue threatening the safety of water conservancy projects. Their complex dynamic evolution characteristics significantly increase the difficulty of detection and monitoring. Traditional monitoring methods, such as manual inspection, sensor technology, remote sensing, and unmanned aerial vehicle technology, are generally characterized by low detection accuracy, insufficient efficiency, and limited penetration capability. Traditional geophysical nondestructive testing methods, including high-resolution electrical resistivity tomography, self-potential method, ground-penetrating radar method, seismic imaging method, transient electromagnetic method, and pseudo-random flow field method, can somewhat reveal the leakage distribution and location information. However, they still fall short in detection accuracy, temporal continuity, and long-term monitoring capability, failing to meet actual engineering needs. In response to the above limitations, this study proposed a technique for monitoring leakage hazards in dikes based on time-lapse high-resolution electrical resistivity tomography. Through high-precision resistivity measurements over multiple periods, the proposed technique enables dynamic tracking and precise identification of leakage hazards, providing reliable technical support for dike safety monitoring. The results indicate that the proposed technique can effectively identify abnormal areas within dikes and assess the severity and development process of hazards by analyzing the resistivity variation trend. Compared to traditional detection methods, the proposed technique achieves higher resolution and more comprehensive hazard information, offering a scientific basis for dike management and maintenance.