ArchiveAgainst the backdrop of the continuous deepening of the "dual carbon" strategy and the comprehensive transition from "dual control of energy consumption" to "dual control of carbon emissions, " the iron & steel and power industries, as two major high-carbon-emitting sectors, face multiple constraints in deep decarbonization, including technology, models, costs, and resources. The two industries inherently possess the coupling foundation of power mutual support and source-load interaction. Coupled with the opportunities brought by the continuous improvement of carbon reduction policies and the increasing maturity of the new power system, they have considerable synergistic carbon reduction potential. However, this potential has not been fully unleashed, and a systematic scale effect has not yet been formed. To address these issues, this paper systematically sorts out the practical pain points of carbon reduction in the two industries, explains the adaptation mechanism of synergistic carbon reduction between iron & steel and power, compares and analyzes the emission reduction effectiveness, investment intensity, and applicable scenarios of typical carbon reduction models, examines the core bottlenecks faced in large-scale implementation, proposes a phased industrialization development path, clarifies the key role of clean energy operation entities oriented toward low-carbon transformation of the iron & steel industry, and puts forward implementation measures, providing theoretical reference and practical pathways for synergistic carbon reduction between iron & steel and power industries.
Against the backdrop of profound transformation in the energy system, the re-electrification of the steel industry is not only key to its own decarbonization but also serves as a strategic bridge connecting energy-intensive industries with the future new power system, playing a crucial role in building a new energy system. Currently, the electrification rate of the steel industry is only about 10%, showing a significant gap from the long-term target of 30%. This paper systematically reviews technological pathways to enhance electrification from three dimensions: low-carbon power supply at the source, electricity substitution at the load end, and source-load smart interaction. The study indicates that low-carbon power supply (increasing self-generation and renewable energy share) serves as the mid-term backbone; electricity substitution (developing electric arc furnace steelmaking, electric heating, etc.) represents the long-term fundamental direction but faces significant technical and economic challenges; source-load smart interaction is the near-term foundation and prerequisite for the efficient synergy of the former two. Its digital systems have preliminarily achieved "internal optimization" but their capability to participate in "internal-external collaboration" with the grid for demand response remains to be strengthened. The three pathways must be promoted in phases and synergistically to systematically drive the transformation of the steel industry's energy structure.
With the increasing proportion of short-process steelmaking and the advancement of process electrification, the industry's electricity demand is growing rapidly, highlighting the synergistic relationship between steel emission reduction pathways and the decarbonization of the power system. This study adopts a bottom-up accounting framework to quantify carbon emissions and electricity consumption for three representative steelmaking routes: blast furnace-basic oxygen furnace (BF-BOF), scrap-electric arc furnace (Scrap-EAF), and direct reduced iron-electric arc furnace (DRI-EAF). Under a unified system boundary, the emission intensity and electricity consumption characteristics per ton of steel for different process paths are quantified. On this basis, a projection model for China's steel industry is constructed by integrating key drivers, including crude steel output, process structure evolution, technological improvements, and renewable electricity penetration. Scenario analysis for the period 2020-2060 is conducted to assess emission trajectories and electricity demand. The results show that measures such as demand reduction, process substitution, and energy efficiency improvements can substantially reduce emissions but are insufficient to achieve deep decarbonization on their own. Incorporating power system decarbonization enables the steel sector's emission pathway to largely align with long-term mitigation targets, although a residual emission gap remains toward the end of the transition period. Meanwhile, total electricity demand increases significantly, with a growing reliance on externally supplied electricity, implying higher requirements for generation capacity expansion, renewable energy deployment, and system flexibility. These findings provide quantitative evidence for coordinating steel industry decarbonization strategies with power system planning and the broader low-carbon energy transition.
The large load scale and strong regulation potential of the steel industry can provide flexibility support for industrial virtual power plants under high-proportion renewable energy integration. To address the difficulty of conventional scheduling methods in simultaneously balancing economy, low carbon emissions, and renewable energy accommodation under process constraints in steel production, including minimum production boundaries, ramping limits, daily electricity consumption tasks, and waste-heat utilization coupling, this paper first constructs a typical-day virtual power plant scenario consisting of eight steel enterprises. A multi-objective optimal scheduling model is then established with operating cost, carbon emissions, and renewable energy accommodation as the optimization objectives, while production boundaries, ramping limits, daily electricity consumption tasks, waste-heat power generation coupling, and energy storage state constraints are incorporated into a unified framework. Second, a physics-informed neural network-based optimization method is proposed, in which state reconstruction and a composite loss function are used to achieve joint training for objective optimization and constraint satisfaction. Finally, a typical-day case study with a 24-hour horizon and 1-hour resolution shows that, compared with MOEA/D and RVEA, the proposed method reduces the comprehensive objective value by approximately 3.4% and 4.8%, respectively, and increases the renewable energy accommodation rate by 10.9 and 7.8 percentage points, respectively. The proposed method can provide a reference for low-carbon collaborative scheduling of energy-intensive industrial virtual power plants.
The hydrogen-based direct reduced iron-electric arc furnace (DRI-EAF) short-process metallurgical route is an important pathway for carbon emission reduction in the steel industry, with particular attention needed on the technical and economic feasibility of renewable energy utilization. This paper develops a hydrogen-based DRI-EAF process model co-powered by wind power and the power grid, and conducts a comparative evaluation of the energy consumption, carbon emissions, and economic performance of this process under direct green power connection from offshore and onshore wind conditions in Zhanjiang, Guangdong. The results show that, compared to onshore wind conditions, offshore wind conditions exhibit stronger wind power supply capacity, lower fluctuation, and less dependence on the grid. As the wind farm scale increases, the renewable energy penetration rate continues to rise, and carbon dioxide emissions continue to decline. At the same wind farm scale, the emission reduction performance under offshore wind conditions is consistently better than that under onshore wind conditions. In terms of economic performance, onshore wind conditions result in a lower steel production cost and a shorter payback period. At an installed capacity of 1 500 MW, the steel production cost per ton under onshore wind conditions is CNY 3 616.32, lower than CNY 4 132.89 under offshore wind conditions. When the onshore wind farm scale is 750 MW, the system has the shortest payback period of 7.66 years.
To address the issues of high carbon emissions and unclear emission reduction pathways in iron and steel enterprises, this study carries out medium- and long-term carbon emission prediction and emission reduction pathway planning. Taking a long-process iron and steel enterprisewith a capacity of tens of millions of tons as an example, three scenarios (baseline, moderate carbon control, deep carbon control) are set based on the LEAP (long-range energy alternatives planning system) model. The emission reduction contributions of four measures (waste heat recovery, power plant retrofitting, green power substitution, CCUS (carbon capture, utilization and storage)) are quantified for 2020—2050. The results show that by 2050, the emission reduction percentage is only 28.68% in the baseline scenario, reaches 36.72% in the moderate scenario (through green power and CCUS synergy), and reaches a maximum of 45.83% in the deep scenario (relying on large-scale green power and CCUS). Carbon control intensity is positively correlated with reduction effectiveness, and green power substitution together with CCUS are the keys to deep decarbonization.
To address the efficient utilization of iron-aluminum symbiotic resources, this study systematically investigated the reduction behavior of its pellets under H2 atmospheres. The effects of reaction temperature, H2 volume fraction, and CaO addition (mass fraction) on the reduction process were examined. The kinetic analysis was then conducted. The results show that, without CaO addition, the reduction degree of the iron-aluminum symbiotic pellets initially increases with rising temperature and H2 volume fraction and then stabilizes. The persists FeAl2O4 after 5 minutes of reaction is the key phase hindering reduction. The addition of CaO effectively inhibits the formation of FeAl2O4 and significantly enhances the reduction rate. An optimal CaO addition range of 6%~8% yields the best results, increasing the final reduction degree by approximately 16.34%. Kinetic analysis indicates that the reduction processes for both CaO-free pellets and those with 8% CaO are controlled by chemical reaction. The apparent activation energies are 40.42 kJ/mol and 33.11 kJ/mol, respectively. These findings can provide a theoretical basis for the clean and efficient utilization of iron-aluminum symbiotic ores.
In view of the relatively low grade of waste heat from blast furnace slag flushing water in the steel industry, which makes it difficult to achieve stepwise utilization of waste heat, a combined cooling, heating and power (CCHP) system that coupled the organic Rankine cycle (ORC) with the absorption refrigeration cycle (ARC) has been proposed in this study, and based on the principles of energy conservation and exergy balance, the thermodynamic calculation model of the CCHP system has been established. In addition, R245fa and ammonia-water solution are selected as the working fluids for the ORC and ARC systems, respectively. The influence laws of ORC evaporation temperature, condensation temperature, and working fluid superheat degree, as well as the ARC evaporation temperature, on the exergy efficiency and heat utilization coefficient of the CCHP system have been analyzed. The results show that an increase in the ORC evaporation temperature can effectively enhance the system exergy efficiency and heat utilization coefficient, while an increase in the ORC condensation temperature reduces the exergy efficiency of the system. The superheat degree of ORC working fluid has a relatively weak impact on system performance, while the ARC evaporation temperature has a more obvious influence. When the heat source temperature exceeds 150 ℃, the heat utilization coefficient of the CCHP system can reach over 70%, and the efficient stepwise conversion of medium-and low-temperature waste heat into electricity, cooling, and thermal energy can be achieved. The research results can provide theoretical references for the high-efficiency recovery of blast furnace slag flushing water waste heat and the design and operation of the multi-energy combined supply system.
The thermodynamic model of a cold storage Carnot battery (CB) system integrated with waste heat recovery was constructed in the current study, and the effects of system thermodynamic parameters on the round-trip efficiency (ηrt), total exergy loss (Etot) and exergy efficiency (ηex) under different cycle working fluids of vapor compression refrigeration (VCR) were studied. Furthermore, the sensitivity analysis of system thermodynamic performance was carried out. The results indicate that for a given VCR working fluid, as the VCR condensation temperature (Tcon,VCR) and organic Rankine cycle (ORC) condensation temperature (Tcon,ORC) rise, the system ηrt and ηex gradually reduce, while the system Etot gradually increases. The higher the VCR sub-cooling degree (Tsc,VCR) and ORC evaporation temperature (Teva,ORC) are, the larger the system ηrt and ηex are, while the smaller the system Etot is. For every 1 K rise in Tcon,VCR, the system ηrt and ηex reduce by an average of 3.55 and 0.54 percentage points, respectively, while for every 1 K rise in Teva,ORC, the ηrt and ηex rise by an average of 0.9% and 0.16%, respectively. Under the same system thermodynamic parameters, R600 as the VCR working fluid has the best system thermodynamic performance. Tcon,VCR has the highest sensitivity for system ηrt and ηex, while the system Etot is the most sensitive to Teva,ORC, and Tsc,VCR has the smallest sensitivity for system thermodynamic performance. For the cold storage CB system, the improvement of system ηrt and ηex should preferentially consider reducing Tcon,VCR, and at this time, the reduction extent in system Etot is also relatively larger. The above research results can provide theoretical support for the design and operation of cold storage CB system.
At present, smelting with a high scrap steel ratio has become a mainstream development trend for iron and steel enterprises. The process of adding scrap steel into hot metal ladles prior to hot metal tapping is widely adopted in practical production to raise the scrap ratio. In this paper, a discrete element mathematical model for scrap particle impact on the lining of hot metal ladles is established to investigate the influences of scrap shape and mass flow rate on the impact force distribution and severely impacted zones of ladle lining during scrap charging. Meanwhile, the buffering effect of residual hot metal with different volumes inside the ladle on impact mitigation is discussed. The results show that under the experimental conditions of this study, flake scrap exerts significantly greater impact on the ladle lining than cylindrical scrap at the initial charging stage, and the impact difference between the two scrap types gradually decreases in the later charging period. The charging rate of scrap is positively correlated with the impact intensity on ladle lining; ahigher feeding rate leads to larger impact load. Moreover, residual hot metal retained in the ladle can effectively alleviate the impact induced by scrap dropping.
This article introduces mainstream photovoltaic (PV) support products, with their performances and respective characteristics. For the steel of 800 MPa high-strength weather-resistant photovoltaic supports, the large number of alloying elements and their complex interactions cause significant performance fluctuations, which affect processing and application. To address this problem, this study proposes an approach using data processing technology to guide production and designs a digital production control platform. The platform uses machine learning algorithms to establish data acquisition and preprocessing, data analysis module, and process optimization module. By analyzing more than 2 000 sets of on-site production data and combining with the accuracy comparison results of five classic models, the weighted average method combining random forest (RF) and deep neural network (DNN) has been finally selected to construct the data analysis module for process optimization guidance. The comparative results show that digital production control technology significantly improves the performance stability of 800 MPa grade weathering steel. Among them, the process capability index of strength increases from inadequate levels (0.89 and 0.67) to excellent and satisfactory levels (1.70 and 1.42). The digital production control platform effectively resolves the stability control problem of multi-alloy designed products, and also provides technical methods and implementation pathways for digital empowerment of the traditional equipment manufacturing industry.
To reveal the impact mechanism of Ti element in Ti-bearing steel grades on the sintering of ladle filler sands, laboratory experiments were conducted to investigate the effect of different Ti contents on the sintering behaviors of silica-based, chromite-based and zircon-based filler sands. The results show that with the increase of Ti content in steel, the liquid phase generated in the sintered sands increases significantly under the impact of liquid steel. The components (e.g., SiO2 and MnO) in the liquid phase react with dissolved Ti in steel, leading to the rise of Ti2O3 content in the liquid phase. Ti in steel can lower the melting point of the liquid phase inside the sintered filler sands, and promote the formation of the liquid phase. Meanwhile, under the impact of Ti, zircon-based filler sands decompose into many fine zirconia particles, and a large number of pores are formed after the shrinkage of the sintered grains. The sintering degree of silica-based filler sands is the severest. Considering both the performance and cost, chromite-based filler sands are more suitable for Ti-bearing steel grades.
To investigate the feasibility of applying high-purity salt-lake magnesia with abundant reserves as a substitute for fused magnesite derived from magnesite in MgO-C bricks, the microstructure and phase assemblage of high-purity salt-lake magnesia prepared from salt-lake brine were analyzed. Meanwhile, two types of MgO-C bricks for steel ladle slag line were fabricated using high-purity salt-lake magnesia and fused magnesite from magnesite as raw materials respectively, with phenolic resin and graphite added as additives. According to national standards, the two brick samples were tested and compared in terms of bulk density, apparent porosity, cold compressive strength, hot modulus of rupture, phase assemblage and microstructure. Industrial comparative trials were further carried out on the slag-line working layer of ladles. The results show that high-purity salt-lake magnesia possesses a dense microstructure, with periclase as its dominant phase, featuring high magnesia content and low impurity levels. The MgO-C bricks prepared from high-purity salt-lake magnesia exhibited superior physicochemical properties compared with the brick produced from magnesite-based fused magnesia. Under steel ladle service conditions, the brick made from salt-lake magnesia could satisfactorily replace the counterpart fabricated from fused magnesite derived from magnesite.
In order to investigate the effect of slag length on the wear of the flue wall during the copper flash smelting process, a numerical analysis has been carried out using a two-fluid model. The results indicate that the wear area on the upstream side of the flue wall increases initially and then decreases as the slag length increases. When the slag length reaches 0.4 m, the wear degree reaches its maximum, with a wear area of 2 m in height and 0.6 m in width. It is found that reducing the slag length can prevent the high-intensity wall erosion which is caused by the high-speed flue flow. Additionally, when the slag length reaches 0.5 m, the wall surface can be protected by altering the flow pattern of the multi-phase flue flow. Furthermore, reducing the airflow rate can effectively weaken the erosion on the flue wall. When the slag length is 0.4 m, a reduction of 2 000 m3/h on the airflow rate from 22 103 m3/h to 12 103 m3/h can result in a corresponding reduction in erosion intensity of 4.8%, 10.5%, 5.6%, 13.2%, and 17.7%, respectively. When the slag length is 0.5 m, the wear intensity in local areas is found to increase as the airflow rate decreases. However, the general trend of reduced erosion with decreasing the airflow rate is consistent with that when the slag length is 0.4 m, and the wear intensity is lower when the slag length is larger.
The uniformity of gas exhaust among cells is a key factor affecting the environmental quality in the potroom. Measurement data from the 350 kA potline show that the total pressure drop in the branch pipes on the side toward which the main collection duct is biased toward generally higher than that on the opposite side. This study establishes a gas flow field model for the branch pipe system and the main collection duct. The computational results indicate that only when the flow area of the branch pipes on the biased side is 11.4% smaller than that on the opposite side can gas exhaust among cells be effectively balanced. This configuration increases the pressure drop of the main collection duct by 13.6% compared to a symmetrically arranged system. The discovery that the bias of the main collection duct inversely affects gas exhaust among cells enhances the aluminum industry's understanding of balanced gas exhaust and provides a theoretical basis for improving potroom environmental quality and thermal balance among cells.
4J29 alloy has been used as the research object, and samples with different Ce additions have been prepared by a vacuum induction furnace. The effects of Ce addition on the microstructure and corrosion resistance of the alloy have been systematically investigated by means of optical microscope, scanning electron microscope, potentiodynamic polarization curve and electrochemical impedance spectroscopy. The results show that Ce addition can significantly refine the alloy grains, straighten grain boundaries, and modify the original harmful inclusions into fine and well-rounded Ce-containing rare earth inclusions. The transformation path of inclusions is determined to Al2O3→CeAlO3→CeO2S→Ce2O3→CeO2. In 3.5%NaCl(mass fraction) solution, Ce can positively shift the corrosion potential and pitting potential, and reduce the corrosion current density. The corrosion resistance increases first and then decreases slightly with the increase of Ce addition. When the Ce addition is 0.013%, the inclusion refinement is the best, the passive film is the thickest and most compact, and the comprehensive corrosion resistance of the alloy is optimal.
By means of microstructure characterization and property testing, the uniformity of microstructure and properties of a 480 mm thick high-alloyed Al-Zn-Mg-Cu alloy flat ingot prepared by semi-continuous casting in industrial mass production has been investigated. Inductively coupled plasma optical emission spectrometry (ICP-OES) is adopted to detect the distribution of alloying element contents at different thickness positions of the ingot. Optical microscopy (OM), scanning electron microscopy (SEM), and other equipment are used to characterize the grain morphology, type, and content of second phases at various thickness locations. A microhardness tester and electrical conductivity tester are employed to measure the differences in mechanical and conductive properties of the ingot at different thickness positions. The results show that segregation of alloying elements including Zn, Mg, and Cu exists within the range of 100~150 mm from the surface along the thickness direction of the ingot. Four types of grain morphologies appear sequentially along the 8 mm section from the solidified shell layer to the center of the ingot, namely shell fine-grained zone, non-uniform columnar grain zone, equiaxed grain zone with few dendrites and compounds, and local zone with densely distributed dendrites and compounds. The near-surface region of the ingot exhibits a relatively small number of secondary dendrites; as extending from the surface towards the center along the thickness direction, the dendrite features become more prominent, and the grain size increases gradually. In addition, abundant large-sized non-equilibrium second phases are distributed at the 1/4 thickness position of the ingot. Affected by these coarse non-equilibrium precipitates, this position exhibits the lowest microhardness (HV) and highest electrical conductivity, which are 135.6 and 41.2 %IACS, respectively.