收藏切换
Effects of Bentonite on Printability of 3D Printing Mortar
收藏切换
Yi ZHANG, Yanmei ZHU, Qiang REN, Zhengwu JIANG
Journal of the Chinese Ceramic Society | 2022, 50(2) : 420 - 428
Less
收藏切换
Journal of the Chinese Ceramic Society | 2022, 50(2): 420-428
• Research Articles •
Effects of Bentonite on Printability of 3D Printing Mortar
Full
Yi ZHANG, Yanmei ZHU, Qiang REN, Zhengwu JIANG
Affiliations
  • Key Laboratory of Advanced Civil Engineering Materials of Ministry of Education, School of Materials Science and Engineering, Tongji University, Shanghai 201804, China
  • ZHANG Yi (1995-), male, Doctoral candidate. E-mail:

About Author:

ZHANG Yi (1995-), male, Doctoral candidate. E-mail:

Published: 2022-02-20 doi: 10.14062/j.issn.0454-5648.20210341
Outline
收藏切换

To ascertain the influences of bentonite and its content on the printability of 3D printing mortar, the extrudability of mortar was evaluated via fluidity, and its buildability was evaluated by height retention rate and penetration resistance. Also, the rheological behavior of cement pastes with bentonite was characterized via dynamic and static shear tests. Effects of bentonite and its content on the printability of mortars were analyzed via rheology. The results show that the fluidity of printable mortars is linearly correlated to the plastic viscosity of cement pastes and logarithmically to the dynamic yield stress of cement pastes. Besides, there is an exponential relationship between the height retention rate of printable mortars and the static yield stress of cement pastes. The addition of bentonite in the mortar increases the plastic viscosity and dynamic yield stress of cement pastes, resulting in a decrease in the extrudability of mortar. Also, the addition of bentonite improves the static yield stress and structural rebuilding rate of cement pastes, thereby improving the buildability of mortar. Therefore, appropriate amount of bentonite can make the mortar maintain good extrudability while improving its buildability. A width ratio between the top and bottom layers of the printed sample with 2% bentonite is 0.96.

bentonite  /  3D printing  /  mortar  /  rheological property  /  extrudability  /  buildability
张翼, 朱艳梅, 任强, 蒋正武. 膨润土对3D打印砂浆可打印性能的影响. 硅酸盐学报, 2022 , 50 (2) : 420 -428 . DOI: 10.14062/j.issn.0454-5648.20210341
Yi ZHANG, Yanmei ZHU, Qiang REN, Zhengwu JIANG. Effects of Bentonite on Printability of 3D Printing Mortar[J]. Journal of the Chinese Ceramic Society, 2022 , 50 (2) : 420 -428 . DOI: 10.14062/j.issn.0454-5648.20210341
Year 2022 volume 50 Issue 2
15
2
Cite this Article
BibTeX
Article Info
doi: 10.14062/j.issn.0454-5648.20210341
  • Receive Date:2021-04-28
  • Online Date:2026-10-22
  • Published:2022-02-20
Article Data
Affiliations
History
  • Received:2021-04-28
  • Revised:2021-05-25
Funding
Affiliations
    Key Laboratory of Advanced Civil Engineering Materials of Ministry of Education, School of Materials Science and Engineering, Tongji University, Shanghai 201804, China

Corresponding:

JIANG Zhengwu (1974-), male, Ph. D., Professor. E-mail:
References
Share
https://castjournals.cast.org.cn/joweb/gsyxb/EN/10.14062/j.issn.0454-5648.20210341
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family
属数
Number of
genus
种数
Number of
species
占总种数比例
Percentage of
total species (%)
属
Genus
种数
Number of
species
占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT