Home Journals Articles Updates About
CN
image
收藏切换
Performance of Lattice Structure Scaffold Prepared via Digital Light Processing Manufacture by DLP Technology
收藏切换
Shuaibin HUA1, 2, Hao ZHU3, Jiamin WU1, 2, Zhe ZHAI1, 2, Shuang CHEN1, 2, Kai LIU4, Lijin CHENG1, 2, Jun XIAO3, Yusheng SHI1, 2
Journal of the Chinese Ceramic Society | 2021, 49(4) : 608 - 617
Less
收藏切换
Journal of the Chinese Ceramic Society | 2021, 49(4): 608-617
Performance of Lattice Structure Scaffold Prepared via Digital Light Processing Manufacture by DLP Technology
Full
Shuaibin HUA1, 2, Hao ZHU3, Jiamin WU1, 2, Zhe ZHAI1, 2, Shuang CHEN1, 2, Kai LIU4, Lijin CHENG1, 2, Jun XIAO3, Yusheng SHI1, 2
Affiliations
  • 1.State Key Laboratory of Materials Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
  • 2.Engineering Research Center of Ceramic Materials for Additive Manufacturing, Ministry of Education, Wuhan 430074, China
  • 3.Department of Orthopedic Surgery, Tongji Hospital, Tongji Medical College, Huazhong University of Science and Technology, 1095 Jiefang Avenue, Wuhan 430030, China
  • 4.School of Materials Science and Engineering, Wuhan University of Technology, Wuhan 430070 , China

    • HUA Shuaibin (1998-), male, Master candidate. E-mail:

About Author:

HUA Shuaibin (1998-), male, Master candidate. E-mail:

Published: 2021-04-20 doi: 10.14062/j.issn.0454-5648.20200572
Outline
收藏切换

Bone defects caused by trauma, bone tumor resection, traffic accidents, etc. increase the demand for bone scaffolds and additive manufacturing technology is gradually being widely used in the preparation of bone scaffolds. Three lattice-structured hydroxyapatite (Ca10(PO4)6OH2), HA ceramic green body such as Diamond structure, Rhombic dodecahedron structure and Octet truss structure were manufactured by Digital Light Processing technology and then successfully sintered three kinds of lattice structure HA ceramic scaffolds with a porosity of 70%, and the minimum pore size after sintering is about 200-300 μm. After being sintered at 1 300℃, the HA ceramic is partially decomposed into β-Ca3(PO4)2, and the ceramic grains are tightly bound. Mechanical strength simulation matches actual results, the average compressive strength of the Octet truss structure is the largest, which is 3.16 MPa. In vitro cell experiments showed that the surface of the HA ceramic bone scaffold is beneficial to the spread and adhesion of bone mesenchymal stem cells (rBMSCs), and the HA ceramic prepared by DLP has good biocompatibility. Therefore high-precision lattice structure HA ceramic bone scaffold fabricated by DLP technology is expected to be widely used in bone tissue engineering.

digital light processing  /  photoinhibitor  /  additive manufacturing hydroxyapatite scaffolds  /  lattice structure  /  biological evaluations
化帅斌, 朱皓, 吴甲民, 翟哲, 陈双, 刘凯, 程立金, 肖骏, 史玉升. 点阵结构羟基磷灰石支架的数字光处理制备及性能. 硅酸盐学报, 2021 , 49 (4) : 608 -617 . DOI: 10.14062/j.issn.0454-5648.20200572
Shuaibin HUA, Hao ZHU, Jiamin WU, Zhe ZHAI, Shuang CHEN, Kai LIU, Lijin CHENG, Jun XIAO, Yusheng SHI. Performance of Lattice Structure Scaffold Prepared via Digital Light Processing Manufacture by DLP Technology[J]. Journal of the Chinese Ceramic Society, 2021 , 49 (4) : 608 -617 . DOI: 10.14062/j.issn.0454-5648.20200572
Appendix
Less
Year 2021 volume 49 Issue 4
37
11
Cite this Article
BibTeX
Article Info
doi: 10.14062/j.issn.0454-5648.20200572
  • Receive Date：2020-08-02
  • Online Date：2026-10-30
  • Published：2021-04-20
Article Data
Affiliations
History
  • Received：2020-08-02
  • Revised：2020-08-17
Funding
Affiliations
    1.State Key Laboratory of Materials Processing and Die & Mould Technology, School of Materials Science and Engineering, Huazhong University of Science and Technology, Wuhan 430074, China
    2.Engineering Research Center of Ceramic Materials for Additive Manufacturing, Ministry of Education, Wuhan 430074, China
    3.Department of Orthopedic Surgery, Tongji Hospital, Tongji Medical College, Huazhong University of Science and Technology, 1095 Jiefang Avenue, Wuhan 430030, China
    4.School of Materials Science and Engineering, Wuhan University of Technology, Wuhan 430070 , China

Corresponding:

WU Jiamin (1984-), male, associate Professor. E-mail:
References
Share
https://castjournals.cast.org.cn/joweb/gsyxb/EN/10.14062/j.issn.0454-5648.20200572
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family		 属数
Number of
genus		 种数
Number of
species		 占总种数比例
Percentage of
total species (%)		 属
Genus		 种数
Number of
species		 占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT
Links
Articles
Latest Articles
Most Read
Collections
Updates
Events
News
Multimedia
About
About Us
Contact
No. 86 Xueyuan South Road, Haidian District, Beijing
100081
010-62662699(Operation and Technical Support)
qkjq@cast.org.cn

Copyright © 2025 China Association for Science and Technology. All rights reserved. For all open access content, the relevant licensing terms apply.
Sponsored by the Office of the Leading Group for Cybersecurity and Informatization of CAST, and supported by Science and Technology Review Publishing House