Most ReadWith the increasing proportion of short-process steelmaking and the advancement of process electrification, the industry's electricity demand is growing rapidly, highlighting the synergistic relationship between steel emission reduction pathways and the decarbonization of the power system. This study adopts a bottom-up accounting framework to quantify carbon emissions and electricity consumption for three representative steelmaking routes: blast furnace-basic oxygen furnace (BF-BOF), scrap-electric arc furnace (Scrap-EAF), and direct reduced iron-electric arc furnace (DRI-EAF). Under a unified system boundary, the emission intensity and electricity consumption characteristics per ton of steel for different process paths are quantified. On this basis, a projection model for China's steel industry is constructed by integrating key drivers, including crude steel output, process structure evolution, technological improvements, and renewable electricity penetration. Scenario analysis for the period 2020-2060 is conducted to assess emission trajectories and electricity demand. The results show that measures such as demand reduction, process substitution, and energy efficiency improvements can substantially reduce emissions but are insufficient to achieve deep decarbonization on their own. Incorporating power system decarbonization enables the steel sector's emission pathway to largely align with long-term mitigation targets, although a residual emission gap remains toward the end of the transition period. Meanwhile, total electricity demand increases significantly, with a growing reliance on externally supplied electricity, implying higher requirements for generation capacity expansion, renewable energy deployment, and system flexibility. These findings provide quantitative evidence for coordinating steel industry decarbonization strategies with power system planning and the broader low-carbon energy transition.
In view of the relatively low grade of waste heat from blast furnace slag flushing water in the steel industry, which makes it difficult to achieve stepwise utilization of waste heat, a combined cooling, heating and power (CCHP) system that coupled the organic Rankine cycle (ORC) with the absorption refrigeration cycle (ARC) has been proposed in this study, and based on the principles of energy conservation and exergy balance, the thermodynamic calculation model of the CCHP system has been established. In addition, R245fa and ammonia-water solution are selected as the working fluids for the ORC and ARC systems, respectively. The influence laws of ORC evaporation temperature, condensation temperature, and working fluid superheat degree, as well as the ARC evaporation temperature, on the exergy efficiency and heat utilization coefficient of the CCHP system have been analyzed. The results show that an increase in the ORC evaporation temperature can effectively enhance the system exergy efficiency and heat utilization coefficient, while an increase in the ORC condensation temperature reduces the exergy efficiency of the system. The superheat degree of ORC working fluid has a relatively weak impact on system performance, while the ARC evaporation temperature has a more obvious influence. When the heat source temperature exceeds 150 ℃, the heat utilization coefficient of the CCHP system can reach over 70%, and the efficient stepwise conversion of medium-and low-temperature waste heat into electricity, cooling, and thermal energy can be achieved. The research results can provide theoretical references for the high-efficiency recovery of blast furnace slag flushing water waste heat and the design and operation of the multi-energy combined supply system.
The thermodynamic model of a cold storage Carnot battery (CB) system integrated with waste heat recovery was constructed in the current study, and the effects of system thermodynamic parameters on the round-trip efficiency (ηrt), total exergy loss (Etot) and exergy efficiency (ηex) under different cycle working fluids of vapor compression refrigeration (VCR) were studied. Furthermore, the sensitivity analysis of system thermodynamic performance was carried out. The results indicate that for a given VCR working fluid, as the VCR condensation temperature (Tcon,VCR) and organic Rankine cycle (ORC) condensation temperature (Tcon,ORC) rise, the system ηrt and ηex gradually reduce, while the system Etot gradually increases. The higher the VCR sub-cooling degree (Tsc,VCR) and ORC evaporation temperature (Teva,ORC) are, the larger the system ηrt and ηex are, while the smaller the system Etot is. For every 1 K rise in Tcon,VCR, the system ηrt and ηex reduce by an average of 3.55 and 0.54 percentage points, respectively, while for every 1 K rise in Teva,ORC, the ηrt and ηex rise by an average of 0.9% and 0.16%, respectively. Under the same system thermodynamic parameters, R600 as the VCR working fluid has the best system thermodynamic performance. Tcon,VCR has the highest sensitivity for system ηrt and ηex, while the system Etot is the most sensitive to Teva,ORC, and Tsc,VCR has the smallest sensitivity for system thermodynamic performance. For the cold storage CB system, the improvement of system ηrt and ηex should preferentially consider reducing Tcon,VCR, and at this time, the reduction extent in system Etot is also relatively larger. The above research results can provide theoretical support for the design and operation of cold storage CB system.
Against the backdrop of the continuous deepening of the "dual carbon" strategy and the comprehensive transition from "dual control of energy consumption" to "dual control of carbon emissions, " the iron & steel and power industries, as two major high-carbon-emitting sectors, face multiple constraints in deep decarbonization, including technology, models, costs, and resources. The two industries inherently possess the coupling foundation of power mutual support and source-load interaction. Coupled with the opportunities brought by the continuous improvement of carbon reduction policies and the increasing maturity of the new power system, they have considerable synergistic carbon reduction potential. However, this potential has not been fully unleashed, and a systematic scale effect has not yet been formed. To address these issues, this paper systematically sorts out the practical pain points of carbon reduction in the two industries, explains the adaptation mechanism of synergistic carbon reduction between iron & steel and power, compares and analyzes the emission reduction effectiveness, investment intensity, and applicable scenarios of typical carbon reduction models, examines the core bottlenecks faced in large-scale implementation, proposes a phased industrialization development path, clarifies the key role of clean energy operation entities oriented toward low-carbon transformation of the iron & steel industry, and puts forward implementation measures, providing theoretical reference and practical pathways for synergistic carbon reduction between iron & steel and power industries.
To address the efficient utilization of iron-aluminum symbiotic resources, this study systematically investigated the reduction behavior of its pellets under H2 atmospheres. The effects of reaction temperature, H2 volume fraction, and CaO addition (mass fraction) on the reduction process were examined. The kinetic analysis was then conducted. The results show that, without CaO addition, the reduction degree of the iron-aluminum symbiotic pellets initially increases with rising temperature and H2 volume fraction and then stabilizes. The persists FeAl2O4 after 5 minutes of reaction is the key phase hindering reduction. The addition of CaO effectively inhibits the formation of FeAl2O4 and significantly enhances the reduction rate. An optimal CaO addition range of 6%~8% yields the best results, increasing the final reduction degree by approximately 16.34%. Kinetic analysis indicates that the reduction processes for both CaO-free pellets and those with 8% CaO are controlled by chemical reaction. The apparent activation energies are 40.42 kJ/mol and 33.11 kJ/mol, respectively. These findings can provide a theoretical basis for the clean and efficient utilization of iron-aluminum symbiotic ores.
To address the issues of high carbon emissions and unclear emission reduction pathways in iron and steel enterprises, this study carries out medium- and long-term carbon emission prediction and emission reduction pathway planning. Taking a long-process iron and steel enterprisewith a capacity of tens of millions of tons as an example, three scenarios (baseline, moderate carbon control, deep carbon control) are set based on the LEAP (long-range energy alternatives planning system) model. The emission reduction contributions of four measures (waste heat recovery, power plant retrofitting, green power substitution, CCUS (carbon capture, utilization and storage)) are quantified for 2020—2050. The results show that by 2050, the emission reduction percentage is only 28.68% in the baseline scenario, reaches 36.72% in the moderate scenario (through green power and CCUS synergy), and reaches a maximum of 45.83% in the deep scenario (relying on large-scale green power and CCUS). Carbon control intensity is positively correlated with reduction effectiveness, and green power substitution together with CCUS are the keys to deep decarbonization.
Against the backdrop of profound transformation in the energy system, the re-electrification of the steel industry is not only key to its own decarbonization but also serves as a strategic bridge connecting energy-intensive industries with the future new power system, playing a crucial role in building a new energy system. Currently, the electrification rate of the steel industry is only about 10%, showing a significant gap from the long-term target of 30%. This paper systematically reviews technological pathways to enhance electrification from three dimensions: low-carbon power supply at the source, electricity substitution at the load end, and source-load smart interaction. The study indicates that low-carbon power supply (increasing self-generation and renewable energy share) serves as the mid-term backbone; electricity substitution (developing electric arc furnace steelmaking, electric heating, etc.) represents the long-term fundamental direction but faces significant technical and economic challenges; source-load smart interaction is the near-term foundation and prerequisite for the efficient synergy of the former two. Its digital systems have preliminarily achieved "internal optimization" but their capability to participate in "internal-external collaboration" with the grid for demand response remains to be strengthened. The three pathways must be promoted in phases and synergistically to systematically drive the transformation of the steel industry's energy structure.
To reveal the impact mechanism of Ti element in Ti-bearing steel grades on the sintering of ladle filler sands, laboratory experiments were conducted to investigate the effect of different Ti contents on the sintering behaviors of silica-based, chromite-based and zircon-based filler sands. The results show that with the increase of Ti content in steel, the liquid phase generated in the sintered sands increases significantly under the impact of liquid steel. The components (e.g., SiO2 and MnO) in the liquid phase react with dissolved Ti in steel, leading to the rise of Ti2O3 content in the liquid phase. Ti in steel can lower the melting point of the liquid phase inside the sintered filler sands, and promote the formation of the liquid phase. Meanwhile, under the impact of Ti, zircon-based filler sands decompose into many fine zirconia particles, and a large number of pores are formed after the shrinkage of the sintered grains. The sintering degree of silica-based filler sands is the severest. Considering both the performance and cost, chromite-based filler sands are more suitable for Ti-bearing steel grades.
4J29 alloy has been used as the research object, and samples with different Ce additions have been prepared by a vacuum induction furnace. The effects of Ce addition on the microstructure and corrosion resistance of the alloy have been systematically investigated by means of optical microscope, scanning electron microscope, potentiodynamic polarization curve and electrochemical impedance spectroscopy. The results show that Ce addition can significantly refine the alloy grains, straighten grain boundaries, and modify the original harmful inclusions into fine and well-rounded Ce-containing rare earth inclusions. The transformation path of inclusions is determined to Al2O3→CeAlO3→CeO2S→Ce2O3→CeO2. In 3.5%NaCl(mass fraction) solution, Ce can positively shift the corrosion potential and pitting potential, and reduce the corrosion current density. The corrosion resistance increases first and then decreases slightly with the increase of Ce addition. When the Ce addition is 0.013%, the inclusion refinement is the best, the passive film is the thickest and most compact, and the comprehensive corrosion resistance of the alloy is optimal.
At present, smelting with a high scrap steel ratio has become a mainstream development trend for iron and steel enterprises. The process of adding scrap steel into hot metal ladles prior to hot metal tapping is widely adopted in practical production to raise the scrap ratio. In this paper, a discrete element mathematical model for scrap particle impact on the lining of hot metal ladles is established to investigate the influences of scrap shape and mass flow rate on the impact force distribution and severely impacted zones of ladle lining during scrap charging. Meanwhile, the buffering effect of residual hot metal with different volumes inside the ladle on impact mitigation is discussed. The results show that under the experimental conditions of this study, flake scrap exerts significantly greater impact on the ladle lining than cylindrical scrap at the initial charging stage, and the impact difference between the two scrap types gradually decreases in the later charging period. The charging rate of scrap is positively correlated with the impact intensity on ladle lining; ahigher feeding rate leads to larger impact load. Moreover, residual hot metal retained in the ladle can effectively alleviate the impact induced by scrap dropping.