Latest ArticlesWith 3-[(tert-butoxycarbonyl)amino]propanoic acid(2) and 1-(2-methoxyphenyl)piperazine hydrochloride(3) as starting materials, tert-butyl [3-[4-(2-methoxyphenyl)piperazin-1-yl]-3-oxopropyl]carbamate(4)was obtained by active ester method. 3-[4-(2-Methoxyphenyl)piperazin-1-yl]propylamine trihydrochloride(6 hydrochloride) was prepared by the reduction of 4 followed by removing the Boc protective group. Finally, 6 was condensed with 6-chloro-1,3-dimethylpyrimidine-2,4(1H,3H)-dione(7) to obtain the title compound with an overall yield of above 61.2%(based on 2) and a purity of 99.95%. The target product was confirmed by HPLC, 1H NMR, 13C NMR, MS and elemental analysis. The improved process is suitable for industrial production as it solves the technical problem of localization of key intermediate 6.
The synthetic process of zoledronic acid(1) was improved. With commercially available imidazole(3)and ethyl chloroacetate(4) as raw materials, the intermediate imidazol-1-acetic acid hydrochloride(2 hydrochloride)was obtained by N-alkylation and hydrolysis reaction through a “one pot method” under the presence of potassium tert-butanol. Crude 1 was then synthesized from 2 hydrochloride, with phosphorus trichloride as the phosphonation reagent. The yield was raised from 46% to 87% by increasing the amounts of methanesulfonic acid and phosphorus trichloride and prolonging the reaction time. After recrystallization from water and acetone, 1 was obtained in 68% yield(based on 3) with HPLC purity of 100.0%. The improved process has the characteristics of low production cost, safer and simpler operation and high yield, which makes it amenable for industrial production.
An improved synthetic process of zolpidem tartrate(1) was developed. Glyoxylic acid(4)was reacted with acetic anhydride to obtain 2,2-diacetoxyacetic acid(5), which was chlorinated by thionyl chloride to generate 2,2-diacetoxyacetyl chloride(6). Then, 6 reacted with dimethylamine chloride to provide N,N-dimethyl-2,2-diacetoxyacetamide(7). Finally, 7 was hydrolyzed by pyridinium 4-toluenesulfonate to afford the key intermediate N,N-dimethyl-2-oxoacetamide(8). p-Methylacetophenone(2) was another starting material, and brominated with bromine, followed by the reaction with 2-amino-5-methylpyridine by “one-pot” method to synthesize 6-methyl-2-(4-methylphenyl)-imidazole[1,2-a]pyridine (3), which was converted into α-hydroxyzolpidem(9) via nucleophilic addition with 8, and then 9 was subjected to the reduction by chlorotrimethylsilane/NaI system to bring out zolpidem(10). Finally, the target compound 1 was obtained from 10 through salification with L-(+)-tartaric acid with an overall yield of 52.4%(based on 2)and the purity of 99.89%. The process was stable with simple operation and low cost, which was suitable for industrial production.
Methyl 8-chloro-6-oxooctanoate(4) was synthesized by acylating chlorination and Nenitzescu reaction from the commercial available material 6-methoxy-6-oxohexanoic acid(2). Then methyl (E)-8-(1,3-dioxoisoindolin-2-yl)-6-(2-tosylhydrazineylidene)octanoate(6) was obtained by substitution and condensation of 4. Ultimately,8-aminooctanoic acid(1) was obtained by reduction, hydrazolysis and hydrolysis reaction from 6, which was an important starting material for the synthesis of the permeation enhancer sodium N-[8-(2-hydroxybenzoyl)amino]octanoate(SNAC). The total yield of this new synthetic route was 58.9%(based on 2) with the purity of 99.83%. This new process is suitable for industrial production with mild conditions, low raw material cost and simple operations.
In an effort to enhance the solubility and oral absorption of quercetin(1), this study employed microfluidic technology to formulate quercetin nanocrystals(QNCs). The research investigated the influences of 1 solution flow rate, anti-solvent phase flow rate, and 1 concentration on the particle size of QNCs. The QNCs were then characterized by a variety of techniques including TEM, DSC, and PXRD. The findings revealed that the particle size of the QNCs could be effectively managed by adjusting the solution flow rate and 1 concentration through microfluidic technology. The formulated QNCs exhibited an amorphous form with a particle size of (79.23±0.45)nm and a polydispersity index(PDI) of (0.144±0.008). Then, an in vitro dissolution test in pH 7.4 PBS was carried out. In addition, a comparative pharmacokinetic study was conducted in rats, in which either QNCs or bulk quercetin were administered orally. Moreover, the QNCs demonstrated an improved dissolution rate in vitro and superior oral bioavailability compared to the bulk drug. These results suggest that microfluidic technology offers significant potential for improving the bioavailability of drugs with poor solubility.
Levothyroxine sodium(1) is the first choice for hypothyroidism treatment, but its therapeutic window is narrow. In clinical use, it is often necessary to use methods such as grinding and breaking to divide the dose, which may reduce the safety. Therefore, this study prepared 1 3D printing tablets, explored the bioequivalence between the 1 3D printed tablets and the reference preparations, and established the correlation between the in vivo absorption and in vitro drug dissolution of the 1 3D printed tablets. The results showed that 1 3D printed tablets and the reference preparations were bioequivalent, and both pharmacokinetic processes could be described by a one-compartment model. The similarity factor (f2) values of the dissolution curves of both preparations in three dissolution media were all above 50. The fitting result of Class A in vitro-in vivo correlation showed that the in vitro cumulative dissolution rate and the in vivo absorption fraction of the 1 3D printed tablets and the reference formulation measured in three dissolution media had a good correlation. This study provided a reference for the in vitro and in vivo evaluation research of 3D printed tablets.
In this study, a LC-MS/MS analytical method was developed for determination of natamycin(1) to assess its distribution in various ocular tissues of New Zealand white rabbits. The results revealed that , after intravitreal administration of 1 to New Zealand white rabbits, 1 was widely distributed in various ocular tissues, particularly in the posterior segment of the eye. The cmax and AUC0→24 of 1 in retina and vitreous were 46 400 and 4 620 ng/g, 232 000 and 29 300 h·ng·g–1, respectively. The results demonstrated that the 1 amounts were higher in both retina and vitreous than in other ocular tissues. After 24 hours post-dosing, the drug concentration remained high level in all ocular tissues, indicating a longer retention of 1. Given this high specificity and reliable results, this established LC-MS/MS method is suitable for investigating distribution of 1 in ocular tissues and can be used to explore further potential treatments for ocular diseases with 1.
In this study, based on the observation of the activity of both gallic acid and ellagic acid against Helicobacter pylori (H. pylori) in vitro, an orthogonal test was used to optimize the extraction process of Hezi Qingyou formula, with the adding amount of water, extraction time and extraction times as influencing factors, content of gallic acid and ellagic acid and extraction rate as evaluation indexes. And the in vitro inhibitory activity of the aqueous extracts against H. pylori was investigated. The results showed that the optimized extraction process of Hezi Qingyou formula was as follows: adding 10 times amount of water, extraction 1.5 h per time and 2 times of extraction. Under these conditions, the aqueous extracts of Hezi Qingyou formula showed significant in vitro inhibition of H. pylori growth in a concentration-dependent manner, with the MIC of 80 - 160 μg/mL.
Qualitative analysis was performed on the characteristic peaks in the fingerprint of Notopterygii Rhizoma et Radix by HPLC-high-resolution mass spectrometry. Notopterygii Rhizoma et Radix was extracted by methanol with ultrasound, and then the supernatant was centrifuged and filtered before analysis. The electric spray ion source was used in positive and negative ion mode, and data was collected in full scan and data-dependent acquisition(DDA)modes. Then, these data were retrieved using LabSolutions Insight software combined with the ChemSpider database to confirm the elemental compositions and possible structural information on twelve characteristic chromatographic peaks in Notopterygium incisum Ting ex H. T. Chang and Notopterygium franchetii H. de Boiss. Among them, 1,5-O-dicaffeoylquinic acid and praeruptorin B were identified for the first time from Notopterygii Rhizoma et Radix. This study provided a reference for expanding the application of Notopterygii Rhizoma et Radix and improving the overall quality evaluation system of Rhizoma et Radix Notopterygii.
The UPLC fingerprints of Cinnamomi Ramulus and its different parts were established, and the differences of Cinnamomi Ramulus and its different parts were investigated by similarity evaluation, chemical pattern recognition and entropy TOPSIS method. The results showed that six common peaks were determined and five components were identified in the fingerprints of Cinnamomi Ramulus, xylem and phloem. The similarity values of Cinnamomi Ramulus, xylem and phloem in ten batches were all greater than 0.990. The results of variance analysis showed that there were significant differences in six components between xylem and phloem. Cluster analysis and principal component analysis showed that the chemical compositions of Cinnamomi Ramulus were more similar to those of phloem than xylem. The results of orthogonal partial least square discriminant analysis could cluster Cinnamomi Ramulus and its different parts into three categories, which were Cinnamomi Ramulus, xylem and phloem. And cinnamaldehyde was screened as the main variable causing the difference of different parts of Cinnamomi Ramulus. The results of entropy TOPSIS method showed that the Euclid approach degree(Ci) of Cinnamomi Ramulus, xylem and phloem were 0.458, 0.249 and 0.577, respectively. The established method can reflect the differences of Cinnamomi Ramulus, and provide a reference for the quality control of Cinnamomi Ramulus.