Home Journals Articles Updates About
CN
image
收藏切换
A Fully Self-Healing Piezoelectric Nanogenerator for Self-Powered Pressure Sensing Electronic Skin
收藏切换
PDF
Maosen Yang1, Jinmei Liu1, Dong Liu1, Jingyi Jiao1, Nuanyang Cui1, Shuhai Liu2, Qi Xu1, Long Gu1, Yong Qin2
Research. Vol 2021 Article ID 9793458
Less
收藏切换
Research. Vol 2021 Article ID 9793458
• Research Article •
A Fully Self-Healing Piezoelectric Nanogenerator for Self-Powered Pressure Sensing Electronic Skin
Full
Maosen Yang1, Jinmei Liu1, Dong Liu1, Jingyi Jiao1, Nuanyang Cui1, Shuhai Liu2, Qi Xu1, Long Gu1, Yong Qin2
Affiliations
  • 1School of Advanced Materials and Nanotechnology, Xidian University, Xi’an 710071, China
  • 2Institute of Nanoscience and Nanotechnology, Lanzhou University, Gansu 730000, China
About Author:

Authors’ Contributions

M. S. Yang with assistance from L. Gu conducted the experiments and analyzed the results. L. Gu, J. M. Liu, and Y. Qin gave suggestions about the experiments. L. Gu and Y. Qin supervised the study and designed the experiments. All authors contributed to the discussion and interpretation of the results.

Published: 2021-04-20 doi: 10.34133/2021/9793458
Outline
收藏切换

As an important way of converting mechanical energy into electric energy, a piezoelectric nanogenerator (PENG) has been widely applied in energy harvesting as well as self-powered sensors in recent years. However, its robustness and durability are still severely challenged by frequent and inevitable mechanical impacts in real application environments. Herein, a fully self-healing PENG (FS-PENG) as a self-powered pressure sensing electronic skin is reported. The self-healing piezoelectric composite and self-healing Ag NW electrode fabricated through mixing piezoelectric PZT particles and conductive Ag NWs into self-healing polydimethylsiloxane (H-PDMS) are assembled into the sandwich structure FS-PENG. The FS-PENG could not only effectively convert external stimulation into electrical signals with a linear response to the pressure but also retain the excellent self-healing and stable sensing property after multiple cycles of cutting and self-healing process. Moreover, a self-healing pressure sensor array composed of 9 FS-PENGs was attached on the back of the human hand to mimic the human skin, and accurate monitoring of the spatial position distribution and magnitude of the pressure was successfully realized.

Maosen Yang, Jinmei Liu, Dong Liu, Jingyi Jiao, Nuanyang Cui, Shuhai Liu, Qi Xu, Long Gu, Yong Qin. A Fully Self-Healing Piezoelectric Nanogenerator for Self-Powered Pressure Sensing Electronic Skin[J]. Research, 2021 , 2021 (4) : 9793458 - . DOI: 10.34133/2021/9793458
Full Text
Less
1. Introduction
Less
With the wide application of micro/nanoelectronic devices, the increasing demand for batteries causes serious environment issues. Self-powered devices that can harvest energy from ambient environment have been proved to be an effective power supply without environmental pollution [1–3]. Generally speaking, the nanogenerator (NG) is capable of converting mechanical energy into electrical energy based on the piezoelectric effect (PENG) [4–6] or triboelectric effect (TENG) [7–9]. With the merits of high conversion efficiency, low cost, diversified designability, and easy fabrication, NGs have shown immense potential in various applications as a green sustainable power source or a battery-free sensor such as portable/wearable devices [10, 11], artificial skins [12, 13], and sensor networks [14]. However, considering that polymers are the most commonly used matrix materials in PENGs and friction layers and substrate materials in TENGs [15], unpredicted damage could be inevitably induced by external mechanical action such as violent interface friction, frequent deformation, and accidental cut and scratch, resulting in the degradation of output performance or even failing to work. Inspired by self-healing property of biological skin, the development of advanced self-healing NGs is an effective strategy to handle this problem [16–22].
In recent years, massive efforts have been made to design and fabricate self-healing NGs. For example, Parida’s group adopted the self-healing ionic conductors as electrodes of TENG to improve the output performance and the stability of the devices and successfully applied them in human skin tactile sensing [17]. Sun’s group combined the conductive silver nanowires (Ag NWs) and self-healing polydimethylsiloxane to fabricate a self-healing and scalable TENG. The TENG was utilized as a flexible electronic skin that could reach 100% of the initial output value after cutting and repairing [18]. Moreover, as an electronic device physically contacting with human skin, the synergistic interaction between the device and the human skin is particularly important. Toward this, Dai’s group designed a self-healing and scalable TENG by introducing the reversible imine and tetrahedral hydrogen bonds (UPy) to the polymer network. Making use of the spontaneous infrared radiation of human skin to promote the self-healing of the friction layers, a wearable motion monitoring sensor for human-computer interaction was successfully realized [22]. However, TENGs are very sensitive to the change of working environment such as humidity [23, 24], temperature [25, 26], and dust particles [27, 28] so that its output performance is unstable which is not conductive to the sensing system. Considering PENG’s stability is much stronger than TENG [29–33], if the self-healing strategy could be introduced to design PENG, it will be very helpful to the development and application of NGs, especially in self-powered sensing system.
In this work, a fully self-healing PENG (FS-PENG) with sandwich structure was developed. It can effectively convert external stimulation into electrical signals exhibiting a linear response to the pressure, retain the excellent self-healing and stable sensing property after multiple cycles of cutting and self-healing process, and be utilized as a self-powered pressure sensing electronic skin.
2. Result and Discussions
Less
2.1. Design and Fabrication of FS-PENG
In the fabrication process of FS-PENG, 4,4′-methylene bis phenyl urea (MPU) and isofordone biuret (IU) were firstly added into double 3-amino-propyl terminated polydimethylsiloxane (NH2-PDMS-NH2, Mn=5000) and mixed uniformly to form the precursor solution of H-PDMS. Subsequently, PZT particles and conductive Ag NW networks were incorporated with H-PDMS solution, respectively, to get the self-healing piezoelectric composite and Ag NW electrode. The SEM image and X-ray diffraction graph of PZT particles were shown in Figure S1. The detailed fabrication process of H-PDMS and the Ag NW conductive network were described in Materials and Methods. Finally, a FS-PENG with a sandwich structure could be simply assembled by the piezoelectric composite and Ag NW electrodes due to abundant dynamic hydrogen bonds in H-PDMS [34], as shown in Figure 1(a). Surface morphology of the self-healing PZT composite and Ag NW electrode was characterized by SEM (Figures 1(b) and 1(c)). It could be found that PZT particles were uniformly dispersed in H-PDMS (Figure 1(b)). In addition, we also found that numerous Ag NWs were closely connected to each other constructing a network structure that is embedded in H-PDMS (Figure 1(c)). The network structure provided an essential foundation for reconnection between Ag NWs in the self-healing process of H-PDMS. Optical images of the FS-PENG with a sandwich structure were shown in Figure 1(d). The thin gray layers on the top and bottom were two self-healing Ag NW electrodes, and the thick white layer in the middle was self-healing PZT composite. Benefitting from the superior mechanical property of H-PDMS, the FS-PENG could be bended, twisted, and stretched without damage, as shown in Figure 1(d), which exhibits excellent flexibility. The chemical structure formula and self-healing mechanism of H-PDMS were schematically shown in Figure 1(e). MPU and IU molecules could incorporate with NH2-PDMS-NH2 forming elasticity strong hydrogen bonding (Crosslinking part 1) and weak hydrogen bonding (Crosslinking part 2), respectively, through polycondensation reaction. These interactions lead to the formation of the cross-linked polymer network of H-PDMS, which provides the elastic mechanism and energy dissipation mechanism, respectively, for the self-healing process of H-PDMS [34]. Specifically, strong hydrogen bonding that resulted from MPU provides high tensile property which is important for flexible electronics, while weak hydrogen bonding resulted by IU contributes greatly to the self-healing property. Moreover, IU also acts as an important role in reducing glass transition temperature (Tg) of H-PDMS by preventing agglomeration of a large number of MPU. Therefore, because of abundant dynamic hydrogen bonds in the elastomer and the low Tg (lower than room temperature) of the H-PDMS backbone, FS-PENG could exhibit excellent self-healing property in absence of external stimulus at room temperature.
2.2. Self-Healing Property of FS-PENG
To verify the self-healing property of the FS-PENG, a device with size of 2.8 cm×1.5 cm was cut into two separate parts, as shown in Figure 2(a). From left to right, the optical images were FS-PENG in the state of before cutting, after cutting, and after healing. It could be seen that the two parts recombined to be a whole one when putting them together without any external stimulus at room temperature. The corresponding resistances of the Ag NW electrode in the above three states were also measured by multimeter. The pristine electrode showed good conductivity with resistance value of 6.5 Ω, and then, the value changed to be overload (ranges of multimeter was 20 MΩ) which meant that the electrodes on the divided two parts were disconnected. After the self-healing process, the resistance recovered to about 55.7  Ω which demonstrated that the conductivity of the electrode was almost completely healed on account of the reconnection of the Ag NW network structure. The same operation was conducted on the bottom electrode, and its conductivity was also recovered. Normally, the two electrodes of PENG should not be short circuit so that the potential difference between the two electrodes could be created by external stimulus. To verify the conducting state between the top and bottom Ag NW electrodes after the self-healing process, resistance between the two electrodes was measured and shown in Figure 1(b). The resistance value showed overload (ranges of multimeter was 20 MΩ) demonstrating that the two electrodes were not in cross-contact after the healing process. The cross-section images of the FS-PENG after healing were characterized and shown in Figures 1(c) and 1(d). No crevices could be found between the interface of Ag NW electrodes and PZT composite (70 wt%), meanwhile, and the incision was perfectly healed, which demonstrated the excellent self-healing property of FS-PENG. Moreover, the tensile test was conducted to FS-PENGs without PZT and with 70 wt% PZT at a uniaxial tensile speed of 10 mm/min, as shown in Figure 2(e). For the FS-PENG without PZT, the ultimate breaking strain was 1100% at stress of 32 kPa (black curve). Subsequently, it was cut into two parts and then healed at room temperature for 12 hours, and the mechanical property of this device recovered almost to its initial state (red curve). The same test was adopted to FS-PENG with PZT (70 wt%); the stress-strain curves before it was damaged (blue curve) and after healing (purple curve) were recorded. It could be found that the modulus of FS-PENG was increased while the self-healing property was weakened due to the presence of PZT particles which limited the free movement of dynamic hydrogen bonds. Although the mechanical property of FS-PENG (70 wt% PZT) after self-healing was weakened, it was enough to meet the design and application demand of flexible electronic devices with self-healing property.
2.3. Working Mechanism and Output Performance of FS-PENG
The working mechanism of FS-PENG was schematically shown in Figure 3(a). When periodic deformation was applied on the FS-PENG by external stimulus, electrical dipole moments in PZT particles would induce a periodically changing potential difference between the two electrodes. As a result, the free electrons in the external circuit could be driven to flow back and forth to generate AC electric output signals. Because the piezoelectric effect of FS-PENG was contributed by PZT particles, the content of PZT particles greatly influences the output of FS-PENG. With the driven force of 20 N, the electric output of FS-PENG with size of 1 cm×1 cm was characterized and shown in Figures 3(b)–3(d). It could be found that the output voltage and current increased with the content of PZT particles increasing from 30 wt% to 70 wt%, and then decreased when PZT content further increased to 80 wt%. The reason for this tendency could be explained as follows: PENG could be considered a capacitor in which the electric charge was generated by the piezoelectric effect [35]. With the filler content of PZT particles increased in the composite, both of its piezoelectric coefficient and dielectric constant are improved. Higher piezoelectric coefficient improves the charge quantities which contributes to a higher output of FS-PENG. Compared with the piezoelectric coefficient, higher dielectric constant will lower the capacitance causing decreased output of the FS-PENG. In addition, compositional and structural inhomogeneity when mixing too many PZT particles into the composite could also easily lead to breakdown [36], resulting in a decreased piezoelectric coefficient of the piezoelectric composite. Based upon the interaction of the above factors, the output performance of FS-PENG exhibited a tendency of first increase and then decrease with the increasing of PZT content and generated the maximum output voltage and current of 3.2 V and 56.1 nA at the PZT content of 70 wt%. To demonstrate that the output signals were contributed by the piezoelectric effect rather than the triboelectric effect, we measured the outputs of FS-PENGs with 0 wt% and 70 wt% PZT particles before and after polarization (Figure S2). As shown in Figure S2a and b, the output current and voltage of FS-PENG with 0 wt% PZT particles had no obvious difference before and after polarization, and both of their values were much smaller than that of FS-PENGs with PZT particles in Figures 3(b) and 3(c). As for the FS-PENG with 70 wt% PZT particles, its output before polarization was in the same level with that of the one with 0 wt% PZT particles, but the output could be substantially increased after it was polarized (Figure S2c and d). These results could clearly show that the output of our FS-PENGs resulted from the ordered aligned dipole moments in the PZT particles which was same with that we discussed in Figure 3(a). Moreover, FS-PENG was very sensitive to the change of driven pressure. Due to the output of PENG being positively correlated to external pressure, the output current and voltage of FS-PENG gradually increased with the pressure increasing from 1 N to 30 N, as shown in Figures 3(e) and 3(f). The corresponding peak to peak values of output voltage and current were presented in Figure 3(g), and a good linearity relationship could be observed between the output and external pressure. This characteristic was very profitable to the application of PENG in the aspect of flexible pressure sensing.
To investigate the change of FS-PENG’s output performance before and after self-healing, the output voltage and current of FS-PENG in pristine (black), damaged (red), and healed (blue) states were recorded and shown in Figures 4(a) and 4(b). When the FS-PENG was damaged, both of the output voltage and current were dropped down. In contrast, the output current was decreased more than voltage. It was mainly due to that the output voltage depended more on the device’s thickness, while the output current depended more on the device’s active area. When the FS-PENG was cut into two separate parts, only the active area was dramatically decreased for the device. The output of FS-PENG could almost recover to the initial value after self-healing. As the electronic devices might be damaged frequently, the repeated self-healing property of FS-PENG was very important for its application in our real life. As shown in Figures 4(c) and 4(d), the output of FS-PENG after three cycles of cutting and self-healing processes showed no obvious difference compared to the pristine one (Figures 4(c) and 4(d)). Besides, FS-PENG’s output also exhibited excellent stability before and after self-healing (Figure 4(e)). These results demonstrated that our FS-PENG not only had stable output performance but also possessed superior and sustained self-healing property.
2.4. Application of FS-PENGs as a Pressure Monitoring Electronic Skin
The sensitive response to external pressure and excellent self-healing property of FS-PENG make it be capable of being applied as a pressure monitoring electronic skin. To simultaneously realize the pressure and position detecting, 9 FS-PENGs with size of 0.5 cm×0.5 cm were combined together as a self-powered sensing arrays and then attached on the back of a human hand acting as a bionic electronic skin, which was shown in Figure 5(a). When the external stimulus was applied on the electronic skin, the measure system recorded 9 parallel output signals generated by each FS-PENG at the same time. Considering that only the FS-PENGs stimulated for force could generate electric output signals, therefore, the spatial position distribution and magnitude of the pressure could be identified according to the electric output mapping of the electronic skin, as shown in Figures 5(b)–5(d). As one main sense of the human body in contact with the outside world, the skin was immensely impacted by the surroundings often causing contused or cut. To the traditional sensors and electrodes, these natural damages were easy to cause irreversible damage resulting in failure of their functionality. Our FS-PENG was capable of perfectly solving this problem. As shown in Figure 5(e), when one FS-PENG unit was cut into two parts, its output current was significantly weakened which could not provide a correct response to the external stimulus. Through the self-healing process, the two parts reintegrated as a whole one presenting superior self-healing property (Figure 5(f)). Meanwhile, the induced response signal also returned to the initial value which could be seen in Figure 5(f). This function demonstrated the great potential of our FS-PENG in the design and implementation of the self-powered and self-healing electronic skin.
3. Conclusion
Less
In this work, we developed a FS-PENG and demonstrated its application as a self-powered electronic skin for pressure detection. By adjusting the mass ratio of PZT particles in piezoelectric composites, the piezoelectric property of FS-PENG was optimized. At the PZT content of 70 wt%, the maximum output voltage and current reached about 3.2 V and 56.1 nA, respectively. The linear response to driven pressure indicated good sensitivity of FS-PENG to the external pressure change. The results of the tensile experiment and repeated cutting testing showed excellent self-healing and stable sensing properties of FS-PENG. These abilities above were successfully used in constructing a self-healing pressure sensor array to mimic the human skin, which could accurately identify the spatial position distribution and magnitude of the external stimulus. This work provides a feasible way for the design and implementation of a self-powered and self-healing pressure sensor for the development of the electronic skin.
4. Materials and Methods
Less
4.1. Preparation of H-PDMS Solution
The typical steps for preparing healable PDMS-MPUx-IU1−x polymer solution were as follows: firstly, mixing 0.20 g IU and 0.27 g MPU into 8 ml of dichloromethane (CH2Cl2), and stirring for one hour to obtain a milky white turbid solution. Secondly, 10 g NH2-PDMS-NH2 and 0.3 g triethylamine were added into 36 ml CH2Cl2, and then stirred vigorously for 1 hour in ice bath to obtain a uniformly dispersed solution. Thirdly, the above two solutions were mixed together with vigorously stirring in ice bath conditions for 1 hour and then taken the mixed solution out and continue stirring at room temperature for 3-4 days. Finally, the H-PDMS solution was obtained.
4.2. Preparation of Ag NW Self-Healing Electrode
The preparation of the self-healing Ag NW electrode included two steps. Firstly, Ag NW alcohol dispersion (12 mg/ml, Nanjing XFNANO Material Technology Co. Ltd.) was sprayed on a PTFE substrate forming the Ag NW network and then annealed at 100°C for 2 hours to improve its density and conductivity. Secondly, the prepared H-PDMS solution was spin-coated on the annealed Ag NW network and cured at 60°C for 2 hours. Finally, the Ag NW self-healing electrode could be peeled off from the PTFE substrate.
4.3. Preparation of Self-Healing Piezoelectric Composite Film
Surface-modified PZT particles (30, 40, 50, 60, 70, and 80 wt%) were uniformly mixed in the H-PDMS polymer solution by ultrasonic and stirring, and then, the solution was poured into a 6 cm×6 cm polytetrafluoroethylene (PTFE) mold. After volatilization of the solvent at room temperature, the composite film could be peeled off from the mold forming a free-standing piezoelectric composite layer.
4.4. Fabrication of FS-PENG
The 10 mm×10 mm×0.012 mm of Ag NW electrodes (top and bottom layers) and 10 mm×10 mm×0.6 mm of the piezoelectric composite (middle layer) were stacked in sequence as shown in Figure 1(a) forming a sandwich structure. Through the self-healing process which resulted from dynamic hydrogen bonds, the three layers could be assembled as a FS-PENG without any crevices. Finally, the FS-PENG was polarized by a direct electric field of 4 kV/mm.
4.5. Measurement and Characterization
The mechanical tensile test was carried out with the ESM301/Mark-10 system. The size of the samples was 10 mm×5 mm×0.6 mm, and the tensile speed was fixed at 10 mm/min. In the self-healing test, the sample was completely cut into two parts by a commercial razor blade and then healed at room temperature. In the measurement of FS-PENG’s output, a linear motor (Linmot E1100) was used to provide the mechanical stimulation. Low-noise voltage and current preamplifier (SR 560 and 570, Stanford) were used to record the output voltage and current.
Funding
Less
  • Natural Science Basic Research Plan in Shaanxi Province of China(2019JQ-652; 2020JM-182; 2021JQ-200)
  • National Natural Science Foundation of China(81801847)
References
Less
1
Wang Z. L., “Self-powered nanosensors and nanosystems,” Advanced Materials, vol. 24, no. 2, pp. 280–285, 2012
2
Wu W., Pan C., Zhang Y., Wen X. N., and Wang Z. L., “Piezotronics and piezo-phototronics - from single nanodevices to array of devices and then to integrated functional system,” Nano Today, vol. 8, no. 6, pp. 619–642, 2013
3
Wang Z. L., “Triboelectric nanogenerators as new energy technology for self-powered systems and as active mechanical and chemical sensors,” ACS Nano, vol. 7, no. 11, pp. 9533–9557, 2013
4
Deng J. N., Kuang X., Liu R. Y., Ding W. B., Wang A. C., Lai Y. C., Dong K., Wen Z., Wang Y. X., Wang L. L., Qi H. J., Zhang T., and Wang Z. L., “Vitrimer elastomer-based jigsaw puzzle-like healable triboelectric nanogenerator for self-powered wearable electronics,” Advanced Materials, vol. 30, no. 14, article 1705918, 2018
5
Zhang C., Fan Y. J., Li H. Y., Li Y. Y., Zhang L., Cao S. B., Kuang S. Y., Zhao Y. B., Chen A. H., Zhu G., and Wang Z. L., “Fully rollable lead-free poly (vinylidene fluoride)-niobate-based nanogenerator with ultra-flexible nano-network electrodes,” ACS Nano, vol. 12, no. 5, pp. 4803–4811, 2018
6
Wang Z. L., and Song J. H., “Piezoelectric nanogenerators based on zinc oxide nanowire arrays,” Science, vol. 312, no. 5771, pp. 242–246, 2006
7
Wu W. Z., Wang L., Li Y. L., Zhang F., Lin L., Niu S. M., Chenet D., Zhang X., Hao Y. F., Heinz T. F., Hone J., and Wang Z. L., “Piezoelectricity of single-atomic-layer MoS2 for energy conversion and piezotronics,” Nature, vol. 514, no. 7523, pp. 470–474, 2014
8
Zou H. Y., Zhang Y., Guo L. T., Wang P. H., He X., Dai G. Z., Zheng H. W., Chen C. Y., Wang A. C., Xu C., and Wang Z. L., “Quantifying the triboelectric series,” Nature Communications, vol. 10, article 1427, 2019
9
Wang Z. L., “On Maxwell’s displacement current for energy and sensors: the origin of nanogenerators,” Materials Today, vol. 20, no. 2, pp. 74–82, 2017
10
Fan F. R., Tian Z. Q., and Wang Z. L., “Flexible triboelectric generator,” Nano Energy, vol. 1, no. 2, pp. 328–334, 2012
11
He X., Zi Y. L., Guo H. Y., Zheng H. W., Xi Y., Wu C. S., Wang J., Zhang W., Lu C. H., and Wang Z. L., “A highly stretchable fiber-based triboelectric nanogenerator for self-powered wearable electronics,” Advanced Functional Materials, vol. 27, no. 4, article 1604378, 2017
12
Gong S. B., Zhang B. W., Zhang J. X., Wang Z. L., and Ren K. L., “Biocompatible poly(lactic acid)-based hybrid piezoelectric and electret nanogenerator for electronic skin applications,” Advanced Functional Materials, vol. 30, no. 14, article 1908724, 2020
13
Peng X., Dong K., Ye C. Y., Jiang Y., Zhai S. Y., and Cheng R. W., “A breathable, biodegradable, antibacterial, and self-powered electronic skin based on all-nanofiber triboelectric nanogenerators,” Science Advances, vol. 6, no. 26, article eaba9624, 2020
14
Pu X., Liu M. M., Chen X. Y., Sun J. M., Du C. H., Zhang Y., Zhai J. Y., Hu W. G., and Wang Z. L., “Ultrastretchable, transparent triboelectric nanogenerator as electronic skin for biomechanical energy harvesting and tactile sensing,” Science Advances, vol. 3, no. 5, article e1700015, 2017
15
Chen A., Zhang C., Zhu G., and Wang Z. L., “Polymer materials for high-performance triboelectric nanogenerators,” Advanced Science, vol. 7, no. 14, article 2000186, 2020
16
Hou C. Y., Huang T., Wang H. Z., Yu H., Zhang Q. H., and Li Y. G., “A strong and stretchable self-healing film with self-activated pressure sensitivity for potential artificial skin applications,” Scientific Reports, vol. 3, article 3138, 2013
17
Parida K., Kumar V., Wang J. X., Bhavanasi V., Bendi R., and Lee P. S., “Highly transparent, stretchable, and self-healing ionic-skin triboelectric nanogenerators for energy harvesting and touch applications,” Advanced Materials, vol. 29, no. 37, article 1702181, 2017
18
Sun J. M., Pu X., Liu M. M., Yu A. F., Du C. H., Zhai J. Y., Hu W. G., and Wang Z. L., “Self-healable, stretchable, transparent triboelectric nanogenerators as soft power sources,” ACS Nano, vol. 12, no. 6, pp. 6147–6155, 2018
19
Xiong J. Q., Thangavel G., Wang J. X., Zhou X. R., and Lee P. S., “Self-healable sticky porous elastomer for gas-solid interacted power generation,” Science Advances, vol. 6, no. 29, article eabb4246, 2020
20
Chen H. M., Koh J. J., Liu M. M., Li P. J., Fan X. T., Liu S. Q., Yeo J. C. C., Tan Y. J., Tee B. C. K., and He C. B., “Super tough and self-healable poly (dimethylsiloxane) elastomer via hydrogen bonding association and its applications as triboelectric nanogenerators,” ACS Applied Materials & Interfaces, vol. 12, no. 28, pp. 31975–31983, 2020
21
Luo N., Feng Y., Wang D., Zheng Y., and Liu W., “New self-healing triboelectric nanogenerator based on simultaneous repair friction layer and conductive layer,” ACS Applied Materials & Interfaces, vol. 12, no. 27, pp. 30390–30398, 2020
22
Dai X., Huang L. B., Du Y., Han J., and Hao J., “Self-healing, flexible, and tailorable triboelectric nanogenerators for self-powered sensors based on thermal effect of infrared radiation,” Advanced Functional Materials, vol. 30, no. 16, article 1910723, 2020
23
Vu N., and Yang R. S., “Effect of humidity and pressure on the triboelectric nanogenerator,” Nano Energy, vol. 2, no. 5, pp. 604–608, 2013
24
Wen R., Guo J., Yu A., Zhai J., and Wang Z. L., “Humidity-resistive triboelectric nanogenerator fabricated using metal organic framework composite,” Advanced Functional Materials, vol. 29, no. 20, article 1807655, 2019
25
Lu C. X., Han C. B., Gu G. Q., Chen J., Yang Z. W., Jiang T., He C., and Wang Z. L., “Temperature effect on performance of triboelectric nanogenerator,” Advanced Engineering Materials, vol. 19, no. 12, article 1700275, 2017
26
Xu C., Wang A. C., Zou H. Y., Zhang B. B., Zhang C. L., Zi Y. L., Pan L., Wang P. H., Feng P. Z., and Lin Z. Q., “Raising the working temperature of a triboelectric nanogenerator by quenching down electron thermionic emission in contact-electrification,” Advanced Materials, vol. 30, no. 38, article 1803968, 2018
27
Zhou Q. T., Lee K., Kim K. N., Park J. G., Pan J., Bae J., Baik J. M., and Kim T., “High humidity-and contamination-resistant triboelectric nanogenerator with superhydrophobic interface,” Nano Energy, vol. 57, pp. 903–910, 2019
28
Yoon H. J., Kim D. H., Seung W., Khan U., Kim T. Y., Kim T., and Kim S. W., “3D-printed biomimetic-villus structure with maximized surface area for triboelectric nanogenerator and dust filter,” Nano Energy, vol. 63, article 103857, 2019
29
Gu L., Liu J. M., Cui N. Y., Xu Q., Du T., Zhang L., Wang Z., Long C. B., and Qin Y., “Enhancing the current density of a piezoelectric nanogenerator using a three-dimensional intercalation electrode,” Nature Communications, vol. 11, article 1030, 2020
30
Yuan M. M., Cheng L., Xu Q., Wu W. W., Bai S., Gu L., Wang Z., Lu J., Li H., and Qin Y., “Biocompatible nanogenerators through high piezoelectric coefficient 0.5Ba(Zr0.2Ti0.8)O3-0.5(Ba0.7Ca0.3)TiO3 nanowires for in-vivo applications,” Advanced Materials, vol. 26, no. 44, pp. 7432–7437, 2014
31
Gu L., Cui N. Y., Cheng L., Xu Q., Bai S., Yuan M. M., Wu W. W., Liu J. M., Zhao Y., Ma F., Qin Y., and Wang Z. L., “Flexible fiber nanogenerator with 209 V output voltage directly powers a light-emitting diode,” Nano Letters, vol. 13, no. 1, pp. 91–94, 2013
32
Li T., Feng Z. Q., Qu M. H., Yan K., Yuan T., Gao B. B., Wang T., Dong W., and Zheng J., “Core/Shell piezoelectric nanofibers with spatial self-orientated β phase nanocrystals for real-time micropressure monitoring of cardiovascular walls,” ACS Nano, vol. 13, no. 9, pp. 10062–10073, 2019
33
Li T., Qu M. H., Carlos C., Gu L., Jin F., Yuan T., Wu X. W., Xiao J. J., Wang T., Dong W., Wang X. D., and Qi Feng Z., “High-performance poly(vinylidene difluoride)/dopamine core/shell piezoelectric nanofiber and its application for biomedical sensors,” Advanced Materials, vol. 33, no. 3, article 2006093, 2020
34
Kang J., Son D. H., Wang G. N., Liu Y. X., Lopez J., Kim Y., Oh J. Y., Katsumata T., Mun J., Lee Y., Jin L. H., Tok J. B.-H., and Bao Z. N., “Tough and water-insensitive self-healing elastomer for robust electronic skin,” Advanced Materials, vol. 30, no. 13, article 1706846, 2018
35
Zhou X., Xu Q., Bai S., Qin Y., and Liu W. S., “Theoretical study of the BaTiO3 powder’s volume ratio’s influence on the output of composite piezoelectric nanogenerator,” Nanomaterials, vol. 7, no. 6, article 143, 2017
36
Li J., Long Y., Yang F., Wei H., Zhang Z. Y., Wang Y. Z., Wang J. Y., Li C., Carlos C., Dong Y. T., Wu Y. J., Cai W. B., and Wang X. D., “Multifunctional artificial artery from direct 3D printing with built-in ferroelectricity and tissue-matching modulus for real-time sensing and occlusion monitoring,” Advanced Functional Materials, vol. 30, no. 39, article 2002868, 2020
Appendix
Less
Year 2021 volume 2021 Issue 4
PDF
61
34
Cite this Article
BibTeX
Article Info
doi: 10.34133/2021/9793458
  • Receive Date：2021-01-06
  • Online Date：2026-10-27
  • Published：2021-04-20
Article Data
Affiliations
History
  • Received：2021-01-06
  • Accepted：2021-02-25
Funding
Natural Science Basic Research Plan in Shaanxi Province of China(2019JQ-652; 2020JM-182; 2021JQ-200)
National Natural Science Foundation of China(81801847)
Affiliations
    1School of Advanced Materials and Nanotechnology, Xidian University, Xi’an 710071, China
    2Institute of Nanoscience and Nanotechnology, Lanzhou University, Gansu 730000, China
References
Share
https://castjournals.cast.org.cn/joweb/research/EN/10.34133/2021/9793458
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family		 属数
Number of
genus		 种数
Number of
species		 占总种数比例
Percentage of
total species (%)		 属
Genus		 种数
Number of
species		 占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT
Links
Articles
Latest Articles
Most Read
Collections
Updates
Events
News
Multimedia
About
About Us
Contact
No. 86 Xueyuan South Road, Haidian District, Beijing
100081
010-62662699(Operation and Technical Support)
qkjq@cast.org.cn

Copyright © 2025 China Association for Science and Technology. All rights reserved. For all open access content, the relevant licensing terms apply.
Sponsored by the Office of the Leading Group for Cybersecurity and Informatization of CAST, and supported by Science and Technology Review Publishing House