Home Journals Articles Updates About
CN
image
收藏切换
Synergistic Effects of Salt Concentration and Working Temperature towards Dendrite-Free Lithium Deposition
收藏切换
PDF
Panlong Li1, Chao Li1, Yang Yang1, Chanyuan Zhang2, Renhe Wang1, Yao Liu1, Yonggang Wang1, Jiayan Luo2, Xiaoli Dong1, Yongyao Xia1
Research. Vol 2019 Article ID 7481319
Less
收藏切换
Research. Vol 2019 Article ID 7481319
• Research Article •
Synergistic Effects of Salt Concentration and Working Temperature towards Dendrite-Free Lithium Deposition
Full
Panlong Li1, Chao Li1, Yang Yang1, Chanyuan Zhang2, Renhe Wang1, Yao Liu1, Yonggang Wang1, Jiayan Luo2, Xiaoli Dong1, Yongyao Xia1
Affiliations
  • 1Department of Chemistry and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Institute of New Energy, Fudan University, Shanghai 200433, China
  • 2State Key Laboratory of Chemistry Engineering, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072, China
About Author:

Authors’ Contributions

P.L.L. conceived of the idea and designed the experiments. Y.Y.X. and X.L.D. directed the project. J.Y.L. and Y.G.W. gave some useful advice about the project. P.L.L. carried out the experiments. X.L.D. assisted P.L.L. to design the in situ optical cells. C.L. contributed to interpreting the mechanism of high-salt concentration and rising working temperature. Y.Y. assisted P.L.L. to do some experiments. C.Y.Z. gave some advice about assembling full cells. Y.L. gave some advice to assemble the in situ cells. R.H.W. gave some advice about drawing the schematic diagram. P.L.L. wrote the paper. All authors discussed the results and commented on the manuscript.

Published: 2019-10-20 doi: 10.34133/2019/7481319
Outline
收藏切换

The lithium- (Li-) metal anode is crucial for developing high-energy-density batteries, while its dendritic growth and the low charge/discharge Coulombic efficiency in organic electrolytes hinder its practical application. Herein, we employed an in situ optical microscope to investigate the effect of the electrolyte concentration and the working temperature on the Li-plating/-stripping process. It is found that a higher concentration electrolyte can suppress its side reaction to improve the charge/discharge Coulombic efficiency, and a higher temperature can help lithium plate/strip uniformly with less lithium dendritic growth. An average Coulombic efficiency was obtained as high as 99.2% for over 150 cycles with a fixed plating capacity of 2 mAh cm-2 on copper foil in a 3 mol/kg ether-based electrolyte under 60°C, which provides an efficient and facile strategy for developing high-performance Li-metal batteries.

Panlong Li, Chao Li, Yang Yang, Chanyuan Zhang, Renhe Wang, Yao Liu, Yonggang Wang, Jiayan Luo, Xiaoli Dong, Yongyao Xia. Synergistic Effects of Salt Concentration and Working Temperature towards Dendrite-Free Lithium Deposition[J]. Research, 2019 , 2019 (10) : 7481319 - . DOI: 10.34133/2019/7481319
Full Text
Less
1. Introduction
Less
Li-metal anode has been regarded as one of the most promising candidates for next-generation high-energy-density batteries, owing to its ultra-high capacity and low potential [1–3]. Unfortunately, metallic Li shows hyperactivity with various organic solvents, leading to side reactions with commonly used electrolytes [4, 5]. It was widely reported that these reactions could form a solid electrolyte interface (SEI) layer to prevent further anode corrosion [6]. However, once uncontrollable dendrite morphology is formed during long cycles, numerous fractures or cracks will occur in the existing SEI. The newly exposed Li will further consume the electrolyte to form a new SEI film, resulting in low Coulombic efficiency (CE) [7]. Moreover, the uncontrolled dendritic Li metal will cause internal short circuit, even severe safety issues [8].
High CE and dendrite-free behaviour of Li deposition under deep plating/stripping are essential for the practical application of the Li-metal anode [7]. Considerable approaches [9–13] and technologies [14–19] have been focused on achieving these two targets. As an indispensable component of batteries, the electrolyte has been deeply investigated to improve Li deposition behaviour, including modifying solvents [20, 21], additives [22, 23], and lithium salts [5, 24, 25]. Towards organic solvents, glymes are reported to be less reactive with Li than cyclic ethers, esters, and alkyl carbonates [5]. However, there are still side reactions occurring between glymes and the Li-metal anode, resulting in low CE. Recently, applying highly concentrated electrolytes are demonstrated to be an effective strategy to achieve high CE and regulate Li deposition morphology under deep Li-plating/-stripping, because increasing salt concentration is in favour of forming a more stable SEI layer, so as to suppress further reactions with metallic Li [5, 24, 26, 27]. Unfortunately, highly concentrated electrolytes could not fully restrain dendrite Li growth. Even worse, they showed high viscosity and low ionic conductivity, resulting in large nucleation overpotential and internal resistance [28–30].
Apart from electrolytes, temperature is usually regarded as an extrinsic factor to electrochemical reaction kinetics [31], which is seldom studied in Li dendrite formation. Koratkar’s group [32] proposed that self-heating could heal Li dendrites by applying high current density (15 mA cm-2), because the mass transport rate is related to the temperature. The stepped-up Li+ distribution will heal the dendrites and simultaneously smoothen the surface of Li anodes [32]. However, rising temperature will accelerate the reaction of Li metal with electrolytes, which leads to irreversible capacity fading. Hence, more work remains for developing high-energy Li-metal batteries which are dendrite-free and with high CE.
In this work, we propose a high CE and dendrite-free Li deposition behaviour, accomplished through the synergistic effects of electrolyte concentration and working temperature. Highly concentrated electrolytes can effectively increase the CE, and rising temperature helps to guide the homogeneous Li deposition under deep Li-plating/-stripping. In addition, elevated temperature and high-salt concentration contribute to form a stable LiF-rich SEI film, which further suppresses the lithium dendrite growth. As a result, the goals of high average CE and dendrite-free Li deposition are achieved under the optimized condition (3m electrolyte at 60°C). The mechanism of the synergistic effect is revealed through a series of in situ optical microscopy, ex situ scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) characterizations.
2. Results
Less
2.1. Optimization of Electrolyte and Temperature
Ether-based electrolytes with different concentrations were prepared by adding 1 mol/kg (1m), 3 mol/kg (3m), and 5 mol/kg (5m) lithium bis(trifluoromethanesulfonyl)imide (LiN(SO2CF3)2 or LiTFSI) into 1 : 1 vol/vol 1,3-dioxolane/1,2-dimethoxyethane (DOL/DME) with 1% lithium nitrate (LiNO3) (by weight) additive (termed 1m, 3m, and 5m electrolytes, respectively). The boiling point of the liquid electrolyte was studied to determine suitable working temperature for safety concerns. High-salt concentration increases the boiling point of the liquid electrolyte, which ensures a wider temperature range for safe operation (Figure 1(a)). Compared with the boiling point of 1 : 1 vol/vol DOL/DME solvents (81.1°C), those of 1m, 3m, and 5m electrolytes are 88.9°C, 101.4°C, and 117.8°C, respectively. Unfortunately, high-salt concentration magnifies the viscosity of the liquid electrolyte, which slows down the speed of ion transportation and augments the problem of concentration polarization. This will inevitably affect the electrochemical performance of lithium metal deposition such as high polarization voltage and lithium dendrite growth [20]. As shown in Figure 1(b), the viscosity of highly concentrated electrolytes (3m and 5m electrolytes) is much higher than that of the 1m electrolyte at room temperature (27°C). After raising the temperature, the viscosity of highly concentrated electrolytes is reduced dramatically. The viscosity of the 3m electrolyte above 60°C is similar to that of the 1m electrolyte at room temperature. The viscosity of the 5m electrolyte above 80°C is approximate to that of the 3m electrolyte at room temperature (27°C) but is still higher than that of the 1m electrolyte at room temperature (Figure 1(b)).
For another, the ionic conductivity of different concentrated electrolytes was measured in a symmetric Pt|electrolyte|Pt cell by AC impedance spectroscopy. As shown in Figure 1(c) and Figure S1, the ionic conductivity of electrolytes increases with the temperature. The ionic conductivity of the 3m electrolyte at 60°C is 14.0 mS cm-1, which is close to that of the 1m electrolyte at 27°C (11.9 mS cm-1). In spite of the elevated temperature (60°C), the higher concentration of the 5m electrolyte still shows a little lower ionic conductivity (7.4 mS cm-1), owing to its high viscosity. With further increase of the temperature to 80°C, the 5m electrolyte behaves in a similar ionic conductivity of 12.7 mS cm-1. This is because ionic conductivity is proportional to the number of mobile ions and inversely proportional to the viscosity [29].
Moreover, Li-plating/-stripping behaviours in different concentrated electrolytes at various working temperatures were assessed systematically by cyclic voltammetry. As presented in Figure 1(d)–1(f), reversible Li-plating/-stripping can be detected in the three kinds of electrolytes. At 27°C, it showed higher peak current density in the 1m electrolyte than in 3m and 5m (Figure 1(d)), which is attributed to its higher conductivity and lower viscosity. Benefitting from the elevated temperature (60°C and 80°C), the peak current density in concentrated electrolytes (3m and 5m) is evidently improved at 60°C and 80°C, which are close to that of the 1m electrolyte (Figures 1(e) and 1(f)). Notably, proper viscosity and higher Li+ concentration enabled the 3m electrolyte with the highest peak current density at 60°C, proving the effect of increasing the concentration and raising the temperature. The results also preliminarily indicated the synergistic effect of the concentration and temperature.
2.2. Performance of Li-Plating and Li-Stripping on Copper (Cu) Foil
To elucidate the synergistic effects of salt concentration and working temperature, the performance of Li-plating/-stripping on Cu foil was investigated under nine different conditions (three kinds of salt concentrations and three kinds of working temperatures). The Li/Cu half cells were operated at the current density of 0.5 mA cm-2 with a fixed capacity of 0.5 mAh cm-2. The voltage profiles of plating/stripping processes at 27°C in Figure 2(a) reflect the influence of concentration. The 5m electrolyte shows huge polarization compared to that of the 1m and 3m electrolytes, attributing to the large viscosity of the high-salt concentration. Raising the working temperature evidently facilitates to reduce the high viscosity of the electrolyte, so as to decrease the stable platform (Figure S2). Nucleation overpotential is related to the metallic Li nucleation process, which causes the metal to distribute uniformly on the anode surface [35]. The relationship of nucleation overpotential with concentration and temperature is plotted as in Figure 2(b), from which the 3m electrolyte behaves with the smallest overpotential at 60°C. It can be detected that the nucleation process became easier at elevated temperature. This is because mass transport can be sped up with the increase of temperature. But too high a temperature would also bring up severe chemical instability of the electrolyte with the Li metal. Although fresh Li foil showed excellent stability with the 3m electrolyte at 60°C for 30 days (Figure S3(a)), it was visibly darkening and the electrolyte became turbid after merely 1 day at 80°C (Figure S3(b)). After 30 days in the 3m electrolyte at 80°C, the surface of the Li foil was thoroughly blackened (Figure S3(b)), indicating the shortcoming caused by too high a temperature.
High CE is another important factor to assess the Li-plating/-stripping behaviour. Average CEs of the first 100 cycles for the nine different conditions were calculated and compared in Figure 2(c). The applied current density and capacity were 0.5 mA cm-2 and 0.5 mAh cm-2, respectively. Amongst these conditions, the 3m electrolyte shows outstanding CE at 60°C, indicating the optimal effect of concentration and temperature. To further investigate the CEs at higher current density and higher deposited capacity, low viscosity electrolytes (1m and 3m) at 27°C and 60°C were selected to make a comparison. As shown in Figure 2(d), the cells in the 1m electrolyte at 27°C and 60°C can only stay stable for less than 70 cycles at the current density of 1 mA cm-2 with a fixed capacity of 2 mAh cm-2 due to the short circuit caused by dendrite formation. With optimized salt concentration (3m) and temperature (60°C), the cells can keep over 150 stable cycles with high average CE of 99.2%, which is much better than those at room temperature. The corresponding charge/discharge profiles of half cells are given in Figure S4. Li-plating/-stripping performance was also investigated using Li/Li@Cu symmetric cells at 27°C and 60°C in 1m and 3m electrolytes. As shown in Figure S5, these symmetric cells in the 3m electrolyte at 60°C deliver the lowest overpotential and longest lifetime (over 1200 hours) among these four conditions. Meanwhile, Li@Cu/LiFePO4 cells tests were carried out to demonstrate the influence of temperatures and concentrations of electrolytes, which is shown in Figure S6. Those cells in the 3m electrolyte at 60°C show the best cycling performance and lowest overpotential among four kinds of cells in different conditions. These results can well demonstrate the synergistic effects of concentrated electrolyte and elevated temperature on the high performance of Li deposition behaviour such as long lifespan and low overpotential.
2.3. Investigation of Li Dendrite Evolution by In Situ Optical Microscopy
To obtain a better understanding of the dendrite nucleation and growth process, in situ observation was carried out through an optical microscope (Figure 3 and Figure S7). As presented in Figure 3, the electrochemical overpotential increased with the increase of concentration (1m vs. 3m) and decreased with the increase of temperature (27°C vs. 60°C). In turn, distinct growth patterns emerge with various concentrations and temperatures. When working at a low concentration of the 1m electrolyte and temperature of 27°C (Figure 3(a)), dendrites spring out in the initial 30 min and grow into a branch-like structure rapidly (Movie S1). Increasing the temperature to 60°C (Figure 3(b)) can relieve the dendritic structure because the motivated diffusion of Li enables the fusion of the dendrites under high temperature [32]. It can be detected from Figure 3(c) that a different morphology arose when a high concentration (3m) was applied. A large number of tiny branches appeared with longer times of the deposition process, which can be attributed to more nucleation sites in the concentrated electrolyte. Benefitting from high concentration and elevated temperature, there are almost no obvious dendrites through the entire deposition procedure in the 3m electrolyte at 60°C (Figure 3(d)), which evaluated well the synergetic effect of concentration and temperature.
Furthermore, in situ optical observation of Li-plating behaviour was also conducted in LB303 (i.e., 1 mol/L (1 M) LiPF6 in 1 : 1 : 1 vol/vol/vol ethylene carbonate/diethyl carbonate/dimethyl carbonate (EC/DEC/DMC) (Figure S8)), in comparison with the 1m electrolyte (Figure S9 and Movie S2). The behaviour of the former deposited Li tended to form loose and porous deposits due to the drastic side reactions and fragile SEI layer, while the latter started without Li dendrites. However, once the dendrite formation occurred during cycling, Li dendrites grew up out of control (Figure S9 and Movie S2). After using glass fibers as a separator to fabricate in situ cells, Li dendrites were inclined to puncture though the separator according to Figure S10, which is possible owing to the bad mechanical and physical performance of glass fibers.
2.4. Characterization of Li-Metal Deposition by Ex Situ SEM and Ex Situ XPS
Different deposition mechanism leads to various morphologies of deposited Li, which can be revealed with the ex situ SEM characterization, as given in Figure 4. The same procedures with a fixed capacity of 2 mAh cm-2 plated on copper foil were conducted on the different electrolytes and temperatures. It can be depicted from Figure 4(a) that a linear and porous structure was obtained in the 1m electrolyte at 27°C, while a bigger size and relatively smooth surface can be detected in same concentration at 60°C (Figure 4(b)). This means that rising temperature enabled deposited Li without the sharp dendritic features, which is in correspondence with the in situ optical observations. Similarly, the deposited Li showed similar porous morphology in the 3m electrolyte at room temperature of 27°C and a relatively flat surface at 60°C (Figures 4(c) and 4(d)). The densely packed and flat deposition indicated the dendrite-free behaviour in the 3m electrolyte at 60°C, which shows a smaller surface area so as to alleviate the side reactions with the electrolyte. This explained well the high CE at the optimal condition (the concentration of the 3m electrolyte and working temperature of 60°C) in Figure 2.
To further explore the nature of the various deposited Li behaviours, the components of SEI layers were characterized and analysed by X-ray photoelectron spectroscopy (XPS) depth profiles. Ar sputtering was used to remove the impacts of electrode exposure to air. As shown in Figure 5(a)–5(d), the F1s spectrum of four samples under different conditions exhibits two main peaks at ~684.8 eV (attributed to LiF) and 688.8 eV (attributed to CFx) [33]. Before Ar sputtering, the samples in the 3m electrolytes (Figures 5(c) and 5(d)) show higher LiF content than those in the 1m electrolytes (Figures 5(a) and 5(b)). And the samples at 60°C display higher LiF content compared with those at 27°C. These results indicate that higher salt concentration and elevated temperature can effectively induce more LiF content on the SEI layer. It was widely reported that LiF-rich SEI film could effectively protect Li metal and restrain lithium dendrite growth [6, 22]. The spectrum of C1s was analysed in Figure S11. There are four main peaks which attribute to CO32-, CFx/C-SOx, C-O, and C-C/C-H, respectively [33, 34]. Compared to the samples at 27°C, those samples contain less carbon compounds. The function of SEI induced by temperature (60°C) and concentration (3m) has been demonstrated by additional deposition experiment. The Li-plating/-stripping process of the Li/Cu half cell (3m) was tested at 60°C for the first 15 cycles and then at a lower temperature of 27°C. As shown in Figure S12(a)-(b), it is found that the well-formed SEI layer under the condition of 3m and 60°C helps increase the Coulombic efficiencies of Li-plating/-stripping during the following test at 27°C. As detected from Figure S12(c), the surface of lithium deposition morphology is smoother than that sample cycling at 27°C without cycling at 60°C (Figure 4(c)). These results indicate that this SEI layer induced by the synergistic effects of high-salt concentration and elevated temperature can realize higher Coulombic efficiency and uniform lithium deposition in comparison with that sample at 27°C.
3. Discussion
Less
Different deposited Li behaviours were detected with low concentration (1m) and high concentration (3m and 5m) electrolytes. High viscosity of the 5m electrolyte at 27°C-80°C hinders its practical application in the systematic investigation. And 80°C tends to aggravate the side reactions between Li metal and liquid electrolytes. As a consequence, we narrow the range of nine conditions and only investigate four conditions (1m and 3m electrolytes at 27°C and 60°C) in detail. A high concentration electrolyte theoretically increases the concentration of Li+ and TFSI- in comparison to the 1m electrolyte. But high viscosity of concentrated electrolytes slows the mobility of both cations and anions, resulting in inhomogeneous ion distribution and large concentration polarization. Though rough morphology in the 3m electrolyte at room temperature is observed via in situ optical microscopy (Figure 3(c)), lithium dendrites still exist according to the ex situ SEM image (Figure 4(c)). The ionic conductivity of the 3m electrolyte at 60°C is a little bit higher than that of the 1m electrolyte at room temperature (27°C), which indicates that high viscosity of the concentrated electrolyte could be alleviated by raising the working temperature. In addition, raising the temperature will make uniform the distribution of Li+ and reduce the concentration polarization, owing to the accelerated mobility of ions at elevated temperature. Hence, high Li ion concentration and homogeneous anion distribution greatly decentralize the local charge density and impede the tip effect (Figure S13). A more uniform Li+ flux regulates the Li-plating/-stripping behaviour and realizes dendrite-free Li-metal anodes. Moreover, the LiF-rich SEI layer simultaneously suppresses the lithium dendrite and reduces side reactions (resulting in high CE).
In conclusion, we systematically investigate the synergistic effects of electrolyte concentration and elevated temperature on Li-plating/-stripping behaviour. In situ cells were designed to verify the optimized concentration (3 mol/kg) and temperature (60°C) for dendrite-free Li deposition by in situ optical microscopy. XPS depth profiles indicate that raising the temperature and increasing the salt concentration induce the formation of a LiF-rich SEI film, which further restrains dendrite growth and reduces side reactions. High average CE (99.2% over 150 cycles) and dendrite-free lithium deposition are achieved along with a high areal capacity of 2 mAh cm-2 on copper foil. This strategy shows a promising way towards reliable lithium metal anode for practical application.
4. Materials and Methods
Less
4.1. Ionic Conductivity Test
The ionic conductivity of electrolytes was measured by AC impedance spectroscopy from 1 Hz to 1 MHz (BioLogic VSP-300 electrochemical workstation) in a symmetric cell (Pt|electrolyte|Pt).
4.2. Cyclic Voltammogram Test
BioLogic VSP-300 electrochemical workstation was used to obtain cyclic voltammograms of Li-plating/-stripping in different electrolytes by using a Cu foil disc (1.2 mm in diameter) as a working electrode and a Li-metal plate (1.2 mm in diameter) as reference and counter electrode. The scan rate was 0.5 mV s-1.
4.3. Li/Cu Half-Cell Test
The Cu foil was assembled with lithium metal as the counter electrode in the 2016-type coin cells. The electrolyte was 1, 3, and 5 mol/kg LiTFSI (lithium bis(trifluoromethanesulfonyl)imide) (Xiaoyuan, Shanghai, China) and 2 wt% LiNO3 (lithium nitrate) (Aladdin, China) in 1 : 1 (by volume) DOL (1,3-dioxolane) (Xiaoyuan, Shanghai, China) : DME (1,2-dimethoxyethane) (Xiaoyuan, Shanghai, China). The small current of 0.05 mA was set up at the first six cycles to remove the contaminants on the surface of electrodes and activate the batteries.
4.4. Symmetric Cell Test
Symmetric cells were tested by Li@Cu (Cu foil with 2 mAh cm-2 of prelithium) and lithium foil in the 2016-type coin cells. The current density and capacity were set as 0.5 mA cm-2 and 0.5 mAh cm-2.
4.5. Li@Cu/LiFePO4 Cells
LiFePO4 (MTI, Hefei, China) (LiFePO4 : carbon black conductive additive (Super P) : polyvinylidene fluoride (PVDF) = 7 : 2 : 1) on carbon-coated aluminum foil (~1.5 mg cm-2) and Cu foil with prelithium (2 mAh cm-2) were used as the cathode and anode, respectively, to fabricate the 2016-type coin cell. The electrolytes were 1 mol/kg and 3 mol/kg LiTFSI (lithium bis(trifluoromethanesulfonyl)imide) and 2 wt% LiNO3 (lithium nitrate) in 1 : 1 (by volume) DOL (1, 3-dioxolane) : DME (1, 2-dimethoxyethane).
4.6. Material Characterizations
Scanning electron microscopy (SEM) images were acquired by using a Nova NanoSem 450 instrument. A Thermo Fisher HAAKE MARSIII rotary rheometer was used to get the viscosity date of the electrolyte. X-ray photoelectron spectroscopy (XPS) was carried out to characterize the SEI layer of deposited Li by using a XSAM800 Ultra Spectrometer.
Materials and Methods should provide sufficient information to allow replication of the results.
Funding
Less
  • China Postdoctoral Science Foundation(2017M621351)
  • National Postdoctoral Program for Innovative Talents(BX201700054)
  • National Key Research and Development Plan(2016YFB0901500)
  • National Natural Science Foundation of China(21875045)
References
Less
1
Simon P., Gogotsi Y., and Dunn B., “Where do batteries end and supercapacitors begin?,” Science, vol. 343, no. 6176, pp. 1210–1211, 2014
2
Chu S., Cui Y., and Liu N., “The path towards sustainable energy,” Nature Materials, vol. 16, no. 1, pp. 16–22, 2016
3
Armand M., and Tarascon J. M., “Building better batteries,” Nature, vol. 451, no. 7179, pp. 652–657, 2008
4
Aurbach D., Zinigrad E., Cohen Y., and Teller H., “A short review of failure mechanisms of lithium metal and lithiated graphite anodes in liquid electrolyte solutions,” Solid State Ionics, vol. 148, no. 3-4, pp. 405–416, 2002
5
Qian J., Henderson W. A., Xu W., Bhattacharya P., Engelhard M., Borodin O., and Zhang J. G., “High rate and stable cycling of lithium metal anode,” Nature Communications, vol. 6, no. 1, article 6362, 2015
6
Liu B., Zhang J. G., and Xu W., “Advancing lithium metal batteries,” Joule, vol. 2, no. 5, pp. 833–845, 2018
7
Lin D., Liu Y., and Cui Y., “Reviving the lithium metal anode for high-energy batteries,” Nature Nanotechnology, vol. 12, no. 3, pp. 194–206, 2017
8
Tikekar M. D., Choudhury S., Tu Z., and Archer L. A., “Design principles for electrolytes and interfaces for stable lithium-metal batteries,” Nature Energy, vol. 1, no. 9, article 16114, 2016
9
Liang X., Pang Q., Kochetkov I. R., Sempere M. S., Huang H., Sun X., and Nazar L. F., “A facile surface chemistry route to a stabilized lithium metal anode,” Nature Energy, vol. 2, no. 9, article 17119, 2017
10
Li P., Dong X., Li C., Liu J., Liu Y., Feng W., Wang C., Wang Y., and Xia Y., “Anchoring an artificial solid–electrolyte interphase layer on a 3D current collector for high‐performance lithium anodes,” Angewandte Chemie International Edition, vol. 58, no. 7, pp. 2093–2097, 2019
11
Lu Y., Tu Z., and Archer L. A., “Stable lithium electrodeposition in liquid and nanoporous solid electrolytes,” Nature Materials, vol. 13, no. 10, pp. 961–969, 2014
12
Aetukuri N. B., Kitajima S., Jung E., Thompson L. E., Virwani K., Reich M. L., Kunze M., Schneider M., Schmidbauer W., Wilcke W. W., Bethune D. S., Scott J. C., Miller R. D., and Kim H. C., “Flexible ion‐conducting composite membranes for lithium batteries,” Advanced Energy Materials, vol. 5, no. 14, article 1500265, 2015
13
Ding F., Xu W., Graff G. L., Zhang J., Sushko M. L., Chen X., Shao Y., Engelhard M. H., Nie Z., Xiao J., Liu X., Sushko P. V., Liu J., and Zhang J. G., “Dendrite-free lithium deposition via self-healing electrostatic shield mechanism,” Journal of the American Chemical Society, vol. 135, no. 11, pp. 4450–4456, 2013
14
Wang X., Zhang M., Alvarado J., Wang S., Sina M., Lu B., Bouwer J., Xu W., Xiao J., Zhang J. G., Liu J., and Meng Y. S., “New insights on the structure of electrochemically deposited lithium metal and its solid electrolyte interphases via cryogenic TEM,” Nano Letters, vol. 17, no. 12, pp. 7606–7612, 2017
15
Zachman M. J., Tu Z., Choudhury S., Archer L. A., and Kourkoutis L. F., “Cryo-STEM mapping of solid–liquid interfaces and dendrites in lithium-metal batteries,” Nature, vol. 560, no. 7718, pp. 345–349, 2018
16
Li Y., Li Y., Pei A., Yan K., Sun Y., Wu C. L., Joubert L. M., Chin R., Koh A. L., Yu Y., Perrino J., Butz B., Chu S., and Cui Y., “Atomic structure of sensitive battery materials and interfaces revealed by cryo–electron microscopy,” Science, vol. 358, no. 6362, pp. 506–510, 2017
17
Sacci R. L., Black J. M., Balke N., Dudney N. J., More K. L., and Unocic R. R., “Nanoscale imaging of fundamental Li battery chemistry: solid-electrolyte interphase formation and preferential growth of lithium metal nanoclusters,” Nano Letters, vol. 15, no. 3, pp. 2011–2018, 2015
18
Sagane F., Shimokawa R., Sano H., Sakaebe H., and Iriyama Y., “In-situ scanning electron microscopy observations of Li plating and stripping reactions at the lithium phosphorus oxynitride glass electrolyte/Cu interface,” Journal of Power Sources, vol. 225, pp. 245–250, 2013
19
Cheng Q., Wei L., Liu Z., Ni N., Sang Z., Zhu B., Xu W., Chen M., Miao Y., Chen L. Q., Min W., and Yang Y., “Operando and three-dimensional visualization of anion depletion and lithium growth by stimulated Raman scattering microscopy,” Nature Communications, vol. 9, no. 1, p. 2942, 2018
20
Dong X., Lin Y., Li P., Ma Y., Huang J., Bin D., Wang Y., Qi Y., and Xia Y., “High‐energy rechargeable metallic lithium battery at −70°C enabled by a cosolvent electrolyte,” Angewandte Chemie International Edition, vol. 58, no. 17, pp. 5623–5627, 2019
21
Wang J., Yamada Y., Sodeyama K., Chiang C. H., Tateyama Y., and Yamada A., “Superconcentrated electrolytes for a high-voltage lithium-ion battery,” Nature Communications, vol. 7, no. 1, article 12032, 2016
22
Zhang X.-Q., Cheng X.-B., Chen X., Yan C., and Zhang Q., “Fluoroethylene carbonate additives to render uniform Li deposits in lithium metal batteries,” Advanced Functional Materials, vol. 27, no. 10, article 1605989, 2017
23
Zhang S. S., “Role of LiNO3 in rechargeable lithium/sulfur battery,” Electrochimica Acta, vol. 70, pp. 344–348, 2012
24
Qiu F., Li X., Deng H., Wang D., Mu X., He P., and Zhou H., “A concentrated ternary‐salts electrolyte for high reversible Li metal battery with slight excess Li,” Advanced Energy Materials, vol. 9, no. 6, article 1803372, 2019
25
Suo L., Hu Y. S., Li H., Armand M., and Chen L., “A new class of solvent-in-salt electrolyte for high-energy rechargeable metallic lithium batteries,” Nature Communications, vol. 4, no. 1, p. 1481, 2013
26
Zheng J., Yan P., Mei D., Engelhard M. H., Cartmell S. S., Polzin B. J., Wang C., Zhang J. G., and Xu W., “Highly stable operation of lithium metal batteries enabled by the formation of a transient high‐concentration electrolyte layer,” Advanced Energy Materials, vol. 6, no. 8, article 1502151, 2016
27
Alvarado J., Schroeder M. A., Pollard T. P., Wang X., Lee J. Z., Zhang M., Wynn T., Ding M., Borodin O., Meng Y. S., and Xu K., “Bisalt ether electrolytes: a pathway towards lithium metal batteries with Ni-rich cathodes,” Energy & Environmental Science, vol. 12, no. 2, pp. 780–794, 2019
28
Saito S., Watanabe H., Ueno K., Mandai T., Seki S., Tsuzuki S., Kameda Y., Dokko K., Watanabe M., and Umebayashi Y., “Li+ local structure in hydrofluoroether diluted Li-glyme solvate ionic liquid,” The Journal of Physical Chemistry B, vol. 120, no. 13, pp. 3378–3387, 2016
29
Xu K., “Electrolytes and interphases in Li-ion batteries and beyond,” Chemical Reviews, vol. 114, no. 23, pp. 11503–11618, 2014
30
Doi T., Shimizu Y., Hashinokuchi M., and Inaba M., “Low‐viscosity γ‐butyrolactone‐based concentrated electrolyte solutions for LiNi0.5Mn1.5O4 positive electrodes in lithium‐ion batteries,” ChemElectroChem, vol. 4, no. 9, pp. 2398–2403, 2017
31
Andersson A. M., and Edström K., “Chemical composition and morphology of the elevated temperature SEI on graphite,” Journal of The Electrochemical Society, vol. 148, no. 10, pp. A1100–A1109, 2001
32
Li L., Basu S., Wang Y., Chen Z., Hundekar P., Wang B., Shi J., Shi Y., Narayanan S., and Koratkar N., “Self-heating–induced healing of lithium dendrites,” Science, vol. 359, no. 6383, pp. 1513–1516, 2018
33
Jiao S., Ren X., Cao R., Engelhard M. H., Liu Y., Hu D., Mei D., Zheng J., Zhao W., Li Q., Liu N., Adams B. D., Ma C., Liu J., Zhang J. G., and Xu W., “Stable cycling of high-voltage lithium metal batteries in ether electrolytes,” Nature Energy, vol. 3, no. 9, article 199, pp. 739–746, 2018
34
Zheng J., Engelhard M. H., Mei D., Jiao S., Polzin B. J., Zhang J. G., and Xu W., “Electrolyte additive enabled fast charging and stable cycling lithium metal batteries,” Nature Energy, vol. 2, no. 3, article 17012, 2017
35
Zhang R., Chen X. R., Chen X., Cheng X. B., Zhang X. Q., Yan C., and Zhang Q., “Lithiophilic sites in doped graphene guide uniform lithium nucleation for dendrite‐free lithium metal anodes,” Angewandte Chemie International Edition, vol. 56, no. 27, pp. 7764–7768, 2017
Appendix
Less
Year 2019 volume 2019 Issue 10
PDF
40
22
Cite this Article
BibTeX
Article Info
doi: 10.34133/2019/7481319
  • Receive Date：2019-04-23
  • Online Date：2026-10-27
  • Published：2019-10-20
Article Data
Affiliations
History
  • Received：2019-04-23
  • Accepted：2019-10-01
Funding
China Postdoctoral Science Foundation(2017M621351)
National Postdoctoral Program for Innovative Talents(BX201700054)
National Key Research and Development Plan(2016YFB0901500)
National Natural Science Foundation of China(21875045)
Affiliations
    1Department of Chemistry and Shanghai Key Laboratory of Molecular Catalysis and Innovative Materials, Institute of New Energy, Fudan University, Shanghai 200433, China
    2State Key Laboratory of Chemistry Engineering, School of Chemical Engineering and Technology, Tianjin University, Tianjin 300072, China
References
Share
https://castjournals.cast.org.cn/joweb/research/EN/10.34133/2019/7481319
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family		 属数
Number of
genus		 种数
Number of
species		 占总种数比例
Percentage of
total species (%)		 属
Genus		 种数
Number of
species		 占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT
Links
Articles
Latest Articles
Most Read
Collections
Updates
Events
News
Multimedia
About
About Us
Contact
No. 86 Xueyuan South Road, Haidian District, Beijing
100081
010-62662699(Operation and Technical Support)
qkjq@cast.org.cn

Copyright © 2025 China Association for Science and Technology. All rights reserved. For all open access content, the relevant licensing terms apply.
Sponsored by the Office of the Leading Group for Cybersecurity and Informatization of CAST, and supported by Science and Technology Review Publishing House