Home Journals Articles Updates About
CN
image
收藏切换
The Efficacy of Plant-Based Ionizers in Removing Aerosol for COVID-19 Mitigation
收藏切换
PDF
Ady Suwardi1, Chin Chun Ooi2, Dan Daniel1, Chee Kiang Ivan Tan1, Hongying Li2, Ou Yang Zhong Liang2, Yuanting Karen Tang1, Jing Yee Chee1, Anton Sadovoy1, Shu-Ye Jiang3, Srinivasan Ramachandran3, Enyi Ye1, Chang Wei Kang2, Wun Chet Davy Cheong1, Keng Hui Lim2, Xian Jun Loh1
Research. Vol 2021 Article ID 2173642
Less
收藏切换
Research. Vol 2021 Article ID 2173642
• Research Article •
The Efficacy of Plant-Based Ionizers in Removing Aerosol for COVID-19 Mitigation
Full
Ady Suwardi1, Chin Chun Ooi2, Dan Daniel1, Chee Kiang Ivan Tan1, Hongying Li2, Ou Yang Zhong Liang2, Yuanting Karen Tang1, Jing Yee Chee1, Anton Sadovoy1, Shu-Ye Jiang3, Srinivasan Ramachandran3, Enyi Ye1, Chang Wei Kang2, Wun Chet Davy Cheong1, Keng Hui Lim2, Xian Jun Loh1
Affiliations
  • 1Institute of Materials Research and Engineering, 2 Fusionopolis Way, Agency for Science, Technology and Research, Singapore, 138634
  • 2Institute of High Performance Computing, 1 Fusionopolis Way, Agency for Science, Technology and Research, Singapore, 138632
  • 3Temasek Life Sciences Laboratory, 1 Research Link, National University of Singapore, Singapore, 117604
About Author:

Authors’ Contributions

Ady Suwardi, Chee Kiang Ivan Tan, Yuanting Karen Tang, Jingyee Chee, Anton Sadovoy, Enyi Ye, Wun Chet Davy Cheong, and Daniel Dan contributed to the experimental work to quantify the aerosol behaviour. Chin Chun Ooi, Hongying Li, Chang Wei Kang, and Keng Hui Lim contributed on the modeling and analysis. Shu-Ye Jiang and Srinivasan Ramachandran contributed to the plant research and preparation. Xian Jun Loh supervised the work and provided timely advice. Ady Suwardi and Chin Chun Ooi contributed equally to this work.

Published: 2021-02-20 doi: 10.34133/2021/2173642
Outline
收藏切换

Small-sized droplets/aerosol transmission is one of the factors responsible for the spread of COVID-19, in addition to large droplets and surface contamination (fomites). While large droplets and surface contamination can be relatively easier to deal with (i.e., using mask and proper hygiene measures), aerosol presents a different challenge due to their ability to remain airborne for a long time. This calls for mitigation solutions that can rapidly eliminate the airborne aerosol. Pre-COVID-19, air ionizers have been touted as effective tools to eliminate small particulates. In this work, we sought to evaluate the efficacy of a novel plant-based ionizer in eliminating aerosol. It was found that factors such as the ion concentration, humidity, and ventilation can drastically affect the efficacy of aerosol removal. The aerosol removal rate was quantified in terms of ACH (air changes per hour) and CADR- (clean air delivery rate-) equivalent unit, with ACH as high as 12 and CADR as high as 141 ft3/minute being achieved by a plant-based ionizer in a small isolated room. This work provides an important and timely guidance on the effective deployment of ionizers in minimizing the risk of COVID-19 spread via airborne aerosol, especially in a poorly-ventilated environment.

Ady Suwardi, Chin Chun Ooi, Dan Daniel, Chee Kiang Ivan Tan, Hongying Li, Ou Yang Zhong Liang, Yuanting Karen Tang, Jing Yee Chee, Anton Sadovoy, Shu-Ye Jiang, Srinivasan Ramachandran, Enyi Ye, Chang Wei Kang, Wun Chet Davy Cheong, Keng Hui Lim, Xian Jun Loh. The Efficacy of Plant-Based Ionizers in Removing Aerosol for COVID-19 Mitigation[J]. Research, 2021 , 2021 (2) : 2173642 - . DOI: 10.34133/2021/2173642
Full Text
Less
1. Introduction
Less
SARS-COV-2/COVID-19 has resulted in tremendous loss of lives and adversely impacted economies globally. As of December 2020, barely a year after the first cases were reported, more than 75 million people across the world have been infected, with nearly 1.7 million fatalities [1]. Recently, North America and Europe have seen a drastic increase in both the number of new cases and fatalities, adding more than 2 million new cases and 50 thousand new fatalities in a week. This deteriorating situation can be attributed to a multitude of factors such as pandemic fatigue, lack of social distancing, and a poor adherence to mask wearing [2–6]. This worrying development is exacerbated by the winter season in the northern hemisphere where most of the world population resides (i.e., increasing the tendency for people to stay indoor during winter) [7, 8]. Therefore, it is important to identify effective mitigation measures to minimize the virus spread in poorly ventilated indoor environments.
Based on the latest findings, The Centers for Disease Control and Prevention (CDC) has categorized the COVID-19 transmission pathways into three modes, namely, contact transmission (fomites), droplets transmission, and airborne (aerosol) transmission [9]. To mitigate the effects of COVID-19, countries have implemented different measures such as various degrees of lockdown, contact tracing, and social distancing measures [10–12]. When strict enforcements are in place, these measures are effective in minimizing contact and droplets transmission. This was evidenced by the rapidly declining number of cases during the early days of the pandemic in countries with relatively stringent measures [10, 13]. However, unlike contact and large droplets transmission, aerosol can stay suspended in the air for hours and travel over long distances, which present great challenges in mitigation and contact tracing [9, 14]. To date, the understanding of airborne (aerosol) transmission and the effectiveness of appropriate mitigation measures remain unclear [15]. This is not to mention that there is a lack of standardization in particulate matters and bioaerosol sampling techniques [16].
In order to minimize virus spread through aerosol transmission, engineering controls such as ventilation, particle filtration, air disinfection, masks, and engineering air circulation can be used as a low-cost yet effective approach [17–23]. However, some of these measures can be challenging to be implemented across widely varying social settings. While ventilation has been proven to be effective in indoor settings, it cannot be implemented in all places and environmental conditions. These include indoor venues without air-exchangers or where the opening of windows is impractical. In addition, air-disinfection by ultraviolet light has been proven to be effective, but can present negative effects to human health [18]. Finding a readily deployable solution to effectively control and reduce aerosol concentration in a poorly ventilated indoor setting is therefore highly desirable.
Previously, ionizers have been shown to reduce small particulate concentration, airborne bacterial levels, and common influenza virus infectivity [24–26]. Ionizers typically produce negative air ions (NAIs), which are unipolar ions that can electrically charge particulate matter (PM). PM can be efficiently removed in the environment with a high concentration of NAIs, as the charged PM is attracted to nearby surfaces and can settle down more quickly [27–31]. However, a major disadvantage of many ionizers is the emission of ozone, which is harmful to human health [32–34].
Plant-based ionizer has been shown to generate a high concentration of NAIs (up to 82 million ions/cm3) under pulsed electrical field (PEF) conditions while producing no ozone [35]. Plant-based ionizers have been shown to effectively remove PM2.5 level in an enclosed chamber (from around 500 to near 0  μg/m3 within 5 minutes) [35].
In this study, we sought to evaluate the efficacy of plant-based ionizers in reducing the aerosol concentration in a poorly ventilated indoor setting. Different parameters such as the number and size of plant-based ionizers, humidity, and ventilation were varied to evaluate their effects on aerosol removal. To enable intuitive comparison, we quantified the efficacy of the plant-based ionizers in terms of ACH- (air changes per hour-) equivalent. This is useful as ACH is a simple and intuitive metric for evaluating the effectiveness of ventilation in the design of indoor spaces. It is worth noting that the ACH-equivalent value here does not refer to the real air-exchange in the room. Instead, it represents the equivalent aerosol removal rate as a room with the same air exchange rate.
This ACH-equivalent value can also be expressed in terms of CADR- (clean air delivery rate-) equivalent, which is traditionally used to quantify the contaminant removal capacity for air purifiers. Remarkably, in a poorly ventilated 20 m3 room with 1 large plant-based ionizer (SP4000), 95% aerosol reduction was achieved within 7 minutes, which is equivalent to the effect of having ACH of 12 and CADR of 141 ft3/minute. In contrast, the recommended minimum ventilation according to CDC (centers for disease control and prevention) guidelines is 6 ACH. Lastly, it was found that humidity plays an important role in the rate of aerosol removal with or without plant-based ionizers. The findings from this work can be used to guide the effective deployment of plant-based ionizers in poorly ventilated indoor environment.
2. Methodology
Less
2.1. Experimental
Commercially-available plant-based ionizers from Zero2.5 Biotech Pte. Ltd. (model SP2800-denoted as small plant-based ionizers; model CF4000-denoted as coco coir; and model SP4000-denoted as large plant-based ionizer hereon) were used in this study (Figure 1(a)–(c)). The estimated NAIs at 1 m from SP2800 and SP4000 are 200000-400000 and 1 million ions/cm3, respectively (https://negativeairion.com/). As a control, we also compare the efficacy of plant-based ionizers with commercial ionizers. In order to simulate aerosol generated by a human subject, LED-500 fogging machine was used to generate aerosol with a mean particle size of approximately 1  μm in diameter. A mixture of 50% water and 50% glycerol was used as the fogging liquid. Particulate sensors (Sensirion SPS30) were used to detect and quantify the aerosol concentration. In all experiments, the fog machine was used to saturate the room/enclosure with aerosol (Figure 1(e)), aided by a small fan, until the reading in multiple particle sensors across the room shows similar and consistent values. The dimensions of the poorly ventilated room are shown in Figure 1(d). The aerosol concentration was continuously measured with each of the sensors making a measurement every second, with real-time data sent wirelessly to a computer that logs the data. The sensors were calibrated using TSI DustTrak™ DRX Aerosol Monitor 8533 as a reference. To ensure data accuracy, the linearity of the particle sensor was tested and calibrated for 1  μm size aerosol.
2.2. Theoretical Modeling
In order to have an intuitive comparison between the efficiency of plant-based ionizers and the air exchange in a space, we have adopted computational fluid dynamics (CFD) to simulate fluid dynamics as well as the particle movement under different ACH. A generic indoor space of dimensions 2.6 m length×2.8 m width×2.8 m height is modelled, with inlet and outlet slots at the two ends of the ceiling, similar to that of the experimental venue (as in Figure 1(e)). The computer model is illustrated in Figure 1(d). Meshing is conducted using ANSYS FLUENT 2019 via the mosaic meshing scheme. The minimum cell size used is 0.1 mm while the maximum cell size is of length 0.1 m, resulting in a total mesh size of 2.04 million cells. The room is assumed to be empty with no furniture or objects in the room. An operating temperature of 26°C is specified for consistency with the experiments. Inlet and outlet flow velocities are adjusted to provide air changes per hour (ACH) within the room ranging from ACH=1 to ACH=15 for this study. This corresponds to inlet velocities between 0.14 m/s and 2.1 m/s, respectively.
The particles are assumed to be perfectly spherical particles of 1  μm diameter, in accordance with the experiments. The particles are specified with a density of 1130 kg/m3, which corresponds to 50% glycerol and water by mass. This value is close to the density of human saliva (1012 kg/m3) [36]. The inclusion of glycerol in water generally reduces water activity which in turn hinders droplet evaporation. With 50% glycerol in water, it was previously reported that the glycerol-water droplet will have minimal evaporation in an environment with RH=0.66; hence, evaporation is neglected in the numerical simulations [37]. The simulated particles are also assumed to be noninteracting in this set of simulations due to the low particle concentration (<1 ppm).
For all particle simulations, a steady-state simulation is first performed to obtain a converged solution for fluid flow within the domain. The steady-state solution is then used as input for the simulation of particle trajectories based on the discrete phase model. 104 particles are randomly dispersed in the room at the start of each particle simulation, and individual particle trajectories are tracked until the particles either exit the room through the exhaust vents or are trapped on the room’s surfaces. In these simulations, all surfaces in the domain are assumed to be perfect traps for the particles, i.e., particles are assumed to be trapped upon contact with the walls, floor, or ceiling. Similarly to the experiments, the fraction of particles left afloat in the room is tracked with time, and a corresponding decay time constant is calculated.
2.3. Fluid Dynamics and Heat Transfer
The governing equations for fluid mass and momentum with turbulence are
(1)∂ρ∂t+∇·ρu→=m,̇(2)∂ρu→∂t+∇·ρu→u→=−∇P+∇·μ+μt∇u→+∇u→T−∇·23ρκI→+Fm,
where κ is the turbulent kinetic energy and ε is the dissipation of turbulent energy, expressed as
(3)∂ρκ∂t+∇·ρu→κ=∇·μtσk∇κ+Gk−ρε,(4)∂ρε∂t+∇·ρu→ε=∇·μtσε∇ε+εκC1εGk−C2ερε,
where C1ε and C2ε are constants 1.44 and 1.92, respectively, σκ and σε are 1.00 and 1.3, respectively. Gk is the production of turbulence kinetic energy.
Eddy viscosity μτ is expressed as
(5)μt=ρCμκ2ε,
where Cμ is equal to 0.09.
In this work, the realizable k−ε model is used for the modeling of turbulence.
2.4. Droplet Tracking Model
The equation of motion of a droplet (subscript d) is
(6)du→ddt=−FDu→d−u→+g→ρd−ρρd.
u→d and u→ are the droplet and air velocities, respectively. FD is the drag force,
(7)FD=18μρdDd2CDRe24,
where Dd is the droplet diameter and CD is the drag coefficient as a function of the droplet Reynolds number,
(8)CD=c1+c2Re+c3Re2,(9)Re=ρDdu→d−u→μ,
where c1, c2, and c3 are empirical constants for spherical droplets which vary with Reynolds number as follows:
(10)c1,c2,c3=0,24,0  0<Re<0.1,3.69,22.73,0.0903  0.1<Re<1,1.222,1.667,−3.889  1<Re<10,0.6167,46.5,−116.67  10<Re<100,0.3644,98.33,−2778  100<Re<1000,0.357,148.62,−47500  1000<Re<5000,0.46,−490.546,578700  5000<Re<10000,0.5191,−1662.55416700  Re>10000.
2.5. Particle Decay Model
The decay of particles within the room is approximated to first order by the following equation:
(11)Ct=Coe−tτ,
where C is the particle concentration, Co is the particle concentration when t=0, and τ is a characteristic decay constant. τ is a variable, which will vary with different ventilation rates within the indoor space, presence of different plant-based ionizers, and likelihood of the particle to stick to various indoor surfaces upon contact. This is approximated from the rate of decay of particle concentration as measured in the experiments and from the rate of decay of a randomly distributed set of 104 particles in the room in the numerical simulations across different ventilation settings.
2.6. ACH and CADR
To obtain the CADR-equivalent value from an ACH-equivalent in a room with known dimension, the following equation can be applied:
(12)CADR=ACHxV∗35.31560,
where CADR is the clean air delivery rate (ft3/minute), V is the room volume (m3), and ACH is air change per hour.
3. Results and Discussion
Less
Figure 2 shows the laser sheet visualization images which show the behaviour of aerosol around the plant-based ionizer when it is turned off (Figure 2(a)) and on (Figure 2(b)). When the plant-based ionizer is turned on, swirl eddies can be observed around the plant-based ionizer (supplementary movie 1). This points to the air movement due to electrostatic interaction between electrically-charged particles/aerosol around the plant, which helps to accelerate the rate of airborne aerosol settling into fomites on the nearby surfaces. The particles/aerosol is charged due to the negative air ions (NAIs) originated from the plant-based ionizer. Figure 2(c) and (d) shows the direction of aerosol movement near to the wall when the plant-based ionizer is turned off and on, respectively. In the absence of a plant-based ionizer, aerosol travels downward due to gravitational settling. When the plant-based ionizer was turned on, the NAIs charged the aerosol, which induce opposite charges on the nearby surface/wall and consequently being deposited onto the wall as fomites (supplementary video 2). This is graphically illustrated in Figure 2(e).
In order to quantify the efficacy of the NAIs in removing the aerosol, the enclosure was saturated to a target aerosol concentration. In this study, we measured the concentration of the 1  μm sized particles in the aerosol. This size is within the range of the average droplet nuclei size ranging from 0.74–2.12  μm generated during a cough [38]. Our sensors were calibrated to have linear and consistent response up to 5000 particles/cm3. Therefore, for all experiments, only data below 4000 particles/cm3 was used for determining the aerosol decay rate. In addition, various experimental parameters such as the number and size of plants, temperature, humidity, and ventilation were carefully controlled and varied to isolate and reveal the intrinsic efficacy of the plant-based ionizers.
3.1. Number of Plant-Based Ionizers
In all experiments, the temperature and humidity was set at 26.0±0.5°C and 66%, respectively, to ensure consistency. Data were collected over a 30-minute period when the aerosol concentration reached 4000 particles/cm3. Figure 3(a) shows the aerosol concentration vs. time profile as a function of different types of ionizers in a room with a volume of 0.5 m3. Evidently, without any ionizer, it takes around 24 minutes for the aerosol concentration to reduce by 95%. In the absence of ionizer and ventilation, the removal of human-generated aerosol can be attributed to gravitational settling, which depends on aerosol composition and size [39–41]. Turning on a commercial ionizer (inset in Figure 3(a)) reduces the aerosol removal time to 15 minutes. When a small plant-based ionizer was turned on, it shows high efficacy in a 0.5 m3 enclosure in reducing the time taken to clear the aerosol from 24 minutes to 6 minutes. This is significant considering the almost five-fold difference in cumulative particle concentration over the same time period, as shown in the dashed line in Figure 3(a).
In contrast, for 20 m3 enclosure, no substantial effect was observed when 1 small plant-based ionizer was turned on (not shown). This may be due to the limited coverage volume for each plant. When 2 small plant-based ionizers were turned on (Figure 3(b)), the 95% aerosol removal was achieved in slightly over 15 minutes, which is almost 10 minutes faster compared to the removal time without the plant-based ionizer. Lastly, while adding a third plant does decrease the aerosol removal time to slightly below 15 minutes, it is of no substantial improvements as compared to 2 small plant-based ionizers. This suggests that the aerosol removal mechanism by the NAIs is nonlinear, as illustrated by the dashed line which shows the cumulative particle concentration. Furthermore, since the onset for effective aerosol removal in a 20 m3 volume room was observed when 2 small plant-based ionizers were turned on, it can be simplistically estimated that each small plant-based ionizer has a coverage volume of approximately 10 m3.
3.2. Size of Plant-Based Ionizers
In order to examine the efficacy of large size plant-based ionizers compared to small ones, the same set of experiments was conducted in the same temperature and humidity. As shown in Figure 4(a), for a poorly ventilated room, a large plant-based ionizer drastically reduces the aerosol removal time from 25 minutes to just above 6 minutes, which is more effective compared to 2 small plants which takes 14 minutes to achieve the same removal. This observation shows that the size of plant-based ionizer arguably plays an important role in addition to the number of plants. In contrast to the coverage volume of 10 m3 for small plants, this observation suggests that a large plant has a coverage volume of at least 20 m3. The difference in efficacy between large and small plant-based ionizers can be associated to the difference in total surface area of the leaves and the voltage. Large plants have ~10 times larger leaves area and higher voltage (up to 20 kV) compared to small plants (up to 7 kV). Thus, the amount of NAIs produced in large plants is far more than those of the smaller plants [35].
In addition to the size and number of plants, ventilation plays a vital role in aerosol removal. Figure 4(b) shows the negligible effect of plant-based ionizers in a well-ventilated room (ACH>14). In other words, plant-based ionizers can be used to create an ACH-equivalent environment when there is no possible means of natural ventilation. These are useful in situations where there is a split-type air conditioning system or the opening of windows is not possible [42]. It is worth noting that while adding extra plant-based ionizer results in diminishing additional benefit (Figure 3(b)), the decay profile from numerical simulations corresponding to different ACH numbers has a similar nonlinear nature, which is shown in Figure 4(c) and (d). Remarkably, using 3 small plant-based ionizers or a large plant-based ionizer show equivalent effects of adding up to 4 and 12 ACH to the poorly ventilated room, respectively, as summarized in Table 1.
3.3. Coco Coir
Besides using living plants as the plant-based ionizers, plant/fiber-based coco coir shows a similar level of efficacy as a large plant-based ionizer (Figure 4(a)). This is despite the much smaller size of the coco coir (15 cm) compared to large plant (1-meter height). The high efficacy of can be attributed to the high level of NAIs produced by the coco coir (Table 2). Structurally, the origin of high NAIs concentration is associated with the high number of sharp fibers in the coco coir, thus, concentrating higher electric field and generate more ions.
In addition, despite the high level of NAIs, ozone concentration measurement of the coco coir shows no substantial difference to the background ozone level. Both the background and coco coir ozone levels are well within the safe limit by FDA (food and drug administration), as shown in Figure 5.
3.4. Humidity Level and Ventilation
One critical factor that is often neglected in evaluating aerosol and air quality is humidity. As a matter of fact, lower humidity has been reported to lower indoor VOCs (volatile organic compounds) concentration [43]. In this work, the effect of humidity was studied and analyzed by setting and maintaining two different relative humidity (RH) levels: 66% and 95%, respectively. As shown in Figure 6(a), in a poorly ventilated indoor setting with high humidity (RH 95%), the aerosol tends to stay afloat in the air for a very long time. In addition, even with the aid of a large plant-based ionizer, it still takes up to 14 minutes for the aerosol level to be reduced by 95%. This is twice the time taken for the same plant-based ionizer to remove 95% aerosol (7 minutes). More interestingly, in a very humid environment, small plant-based ionizers are not effective in accelerating the aerosol removal, as shown in Figure 6(b).
These observations can be associated with the competing effect brought about by floating water molecules in aerosol removal by NAIs. Therefore, for plant-based ionizers to work effectively, the humidity level has to be closely monitored. In addition, it is important to caution that while low humidity favors more effective aerosol/contaminants removal, it has also been reported that low humidity results in more aerosol generated by human subjects [44]. Thus, in the context of mitigating airborne COVID-19 transmission, further careful study has to be carried out to determine the overarching effect of humidity. It is worth noting that air circulation may help to homogenize the NAI concentration within the room, and therefore in places with air-circulation, the location/placement of the ionizer does not affect its efficacy.
3.5. Experimental Decay Constants
The decay of particles for the various experiments is calculated and presented in the table below.
In general, we note that the use of plant-based ionizers can indeed greatly increase the decay rate from 2 to 4 hr-1 to 25 hr-1 in the room tested. The decay of particles in the modelled indoor space with varying ventilation rates (ACH) is also calculated and presented in Figure 7. This was done to provide an intuitive comparison of the effectiveness of the tested plant-based ionizers relative to adjustments in ventilation rates of similar indoor environments.
For this simplified generic room, the numerical simulations indicate that increasing the inlet flow velocity from a situation where ACH=1 to ACH=15 results in a relatively proportional increase in τ, although this might vary with more complex geometries. As a simple comparison, we further note that an equivalent improvement in τ from the use of 3 small plants or 1 large plant relative to the no plant experimental setting would require a 3.2× and 9.6× increase, respectively, in the inlet volumetric flow rate (or ACH) of the room, from ACH=1 to ACH=5 and ACH=12. It should be noted that a 9.6× increase in the inlet flow velocity of air into the room is anticipated to be very difficult to implement, whereas the installation of a large plant-based ionizer is comparatively straightforward. Lastly, typical ACH values for various indoor settings are listed in Table 3.
In addition, it is worth noting that the ACH-equivalent values reported here is specifically for 1  μm aerosol. The ACH values measured using tracer gas (i.e., CO2), which represents the real air-exchange in the room, tend to overestimate the equivalent ACH for contaminant removal [45]. This is due to the different behaviours of gas and particles (contaminants) which have discrete masses and sizes, and, therefore, more difficult to be purged out. Furthermore, the location of air inlet and outlet (vent) may also affect the contaminant/aerosol removal efficacy (i.e., for the same level of real air-exchange, if the outlet is located near the top of the room/enclosure, it will be more difficult to purge out the contaminants due to the competing effect with gravitational settling).
While ACH-equivalent is a convenient metric to compare the efficacies of various types of plant-based ionizers within the same room/enclosure, it does not provide the air-cleaning capacity of each of these plant-based ionizers. A golden standard to evaluate the efficacy of conventional air-purifiers is the clean air delivery rate (CADR). Although the mechanism for these plant-based ionizers is very different from conventional filter-based purifiers, the aerosol removal efficacy can still be expressed in CADR-equivalent to enable across the board comparison. Table 2 shows the equivalent ACH achieved in a 20 m3 room, CADR, and the NAIs concentration for each plant-based ionizer. Evidently, CADR is a convenient metric to estimate the maximum cleaning capacity (room volume) of each plant-based ionizer to be able to achieve a certain ACH value. In addition, as laid out in earlier discussion on the size and number of plant-based ionizers, NAI concentration is a key determining factor in the efficacy of aerosol removal.
4. Conclusions
Less
In the context of mitigating COVID-19 transmission via aerosol, this work laid out important guiding principles in deploying plant-based ionizers for application in indoor environments. Under realistic operating conditions, an ACH-equivalent of 12 and CADR-equivalent of 141 ft3/minute can be achieved by deploying a proper-sized plant in a poorly ventilated room. The proposed solution using plant-based ionizers is part of a multipronged approach, together with proper safe-distancing, mask-wearing, personal-hygiene, and fomite-disinfecting to further minimize the risk of airborne transmissions.
Funding
Less
  • A*STAR, Singapore(SC25/20-8R1640)
References
Less
1
Dong E., Du H., and Gardner L., “An interactive web-based dashboard to track COVID-19 in real time,” The Lancet Infectious Diseases, vol. 20, no. 5, pp. 533–534, 2020
2
Betsch C., Korn L., Sprengholz P., Felgendreff L., Eitze S., Schmid P., and Böhm R., “Social and behavioral consequences of mask policies during the COVID-19 pandemic,” Proceedings of the National Academy of Sciences of the United States of America, vol. 117, no. 36, pp. 21851–21853, 2020
3
Haischer M. H., Beilfuss R., Hart M. R., Opielinski L., Wrucke D., Zirgaitis G., Uhrich T. D., and Hunter S. K., “Who is wearing a mask? Gender-, age-, and location-related differences during the COVID-19 pandemic,” PLoS One, vol. 15, no. 10, article e0240785, 2020
4
Weill J. A., Stigler M., Deschenes O., and Springborn M. R., “Social distancing responses to COVID-19 emergency declarations strongly differentiated by income,” Proceedings of the National Academy of Sciences, vol. 117, no. 33, pp. 19658–19660, 2020
5
Zhao J., Lee M., Ghader S., Younes H., Darzi A., Xiong C., and Zhang L., “Quarantine Fatigue: first-ever decrease in social distancing measures after the COVID-19 pandemic outbreak before reopening United States,” 2020, https://arxiv.org/abs/2006.03716.
6
Sasangohar F., Jones S. L., Masud F. N., Vahidy F. S., and Kash B. A., “Provider Burnout and Fatigue During the COVID-19 Pandemic: Lessons Learned From a High-Volume Intensive Care Unit,” Anesthesia and Analgesia, vol. 131, no. 1, pp. 106–111, 2020
7
Middleton J., Lopes H., Michelson K., and Reid J., “Planning for a second wave pandemic of COVID-19 and planning for winter,” International Journal of Public Health, vol. 65, no. 9, pp. 1525–1527, 2020
8
Smit A. J., Fitchett J. M., Engelbrecht F. A., Scholes R. J., Dzhivhuho G., and Sweijd N. A., “Winter Is Coming: A Southern Hemisphere Perspective of the Environmental Drivers of SARS-CoV-2 and the Potential Seasonality of COVID-19,” International Journal of Environmental Research and Public Health, vol. 17, no. 16, article 5634, 2020
9
, “Scientific brief: SARS-CoV-2 and potential airborne transmission,” , CDC, January 2021, https://www.cdc.gov/coronavirus/2019-ncov/more/scientific-brief-sars-cov-2.html.
10
Lau H., Khosrawipour V., Kocbach P., Mikolajczyk A., Schubert J., Bania J., and Khosrawipour T., “The positive impact of lockdown in Wuhan on containing the COVID-19 outbreak in China,” Journal of Travel Medicine, vol. 27, no. 3, article taaa037, 2020
11
Kretzschmar M. E., Rozhnova G., Bootsma M. C. J., van Boven M., van de Wijgert J. H. H. M., and Bonten M. J. M., “Impact of delays on effectiveness of contact tracing strategies for COVID-19: a modelling study,” The Lancet Public Health, vol. 5, no. 8, pp. e452–e459, 2020
12
Aleta A., Martín-Corral D., Pastore y Piontti A., Ajelli M., Litvinova M., Chinazzi M., Dean N. E., Halloran M. E., Longini Jr I. M., Merler S., Pentland A., Vespignani A., Moro E., and Moreno Y., “Modelling the impact of testing, contact tracing and household quarantine on second waves of COVID-19,” Nature Human Behaviour, vol. 4, no. 9, pp. 964–971, 2020
13
Ji T., Chen H. L., Xu J., Wu L. N., Li J. J., Chen K., and Qin G. Clinical Infectious Diseases, vol. 71, pp. 1454–1460, 2020
14
Hu J., Lei C., Chen Z., Liu W., Hu X., Pei R., Su Z., Deng F., Huang Y., Sun X., Cao J., and Guan W., “Distribution of airborne SARS-CoV-2 and possible aerosol transmission in Wuhan hospitals, China,” National Science Review, vol. 7, no. 12, pp. 1865–1867, 2020
15
Stadnytskyi V., Bax C. E., Bax A., and Anfinrud P., “The airborne lifetime of small speech droplets and their potential importance in SARS-CoV-2 transmission,” Proceedings of the National Academy of Sciences, vol. 117, no. 22, pp. 11875–11877, 2020
16
Su X., Sutarlie L., and Loh X. J. Chemistry–An Asian Journal, vol. 15, pp. 4241–4255, 2020
17
Morawska L., Tang J. W., Bahnfleth W., Bluyssen P. M., Boerstra A., Buonanno G., Cao J., Dancer S., Floto A., Franchimon F., Haworth C., Hogeling J., Isaxon C., Jimenez J. L., Kurnitski J., Li Y., Loomans M., Marks G., Marr L. C., Mazzarella L., Melikov A. K., Miller S., Milton D. K., Nazaroff W., Nielsen P. V., Noakes C., Peccia J., Querol X., Sekhar C., Seppänen O., Tanabe S. I., Tellier R., Tham K. W., Wargocki P., Wierzbicka A., and Yao M., “How can airborne transmission of COVID-19 indoors be minimised?,” Environment International, vol. 142, article 105832, 2020
18
Buonanno M., Welch D., Shuryak I., and Brenner D. J. Scientific Reports, vol. 10, pp. 1–8, 2020
19
Sun C., and Zhai Z., “The efficacy of social distance and ventilation effectiveness in preventing COVID-19 transmission,” Sustainable Cities and Society, vol. 62, article 102390, 2020
20
Tham K. W., Parshetti G. K., Balasubramanian R., Sekhar C., and Cheong D. K. W., “Mitigating particulate matter exposure in naturally ventilated buildings during haze episodes,” Building and Environment, vol. 128, pp. 96–106, 2018
21
Pan L., Wang C., Jin H., Li J., Yang L., Zheng Y., Wen Y., Tan B. H., Loh X. J., and Chen X., “Lab-on-mask for remote respiratory monitoring,” ACS Materials Letters, vol. 2, no. 9, pp. 1178–1181, 2020
22
Chua M. H., Cheng W., Goh S. S., Kong J., Li B., Lim J. Y. C., Mao L., Wang S., Xue K., Yang L., Ye E., Zhang K., Cheong W. C. D., Tan B. H., Li Z., Tan B. H., and Loh X. J., “Face Masks in the New COVID-19 Normal: Materials, Testing, and Perspectives,” Research, vol. 2020, article 7286735, –40, 2020
23
Lin Q., Lim J. Y. C., Xue K., Yew P. Y. M., Owh C., Chee P. L., and Loh X. J., “Sanitizing agents for virus inactivation and disinfection,” View, vol. 1, no. 2, p. e16, 2020
24
Hobbs P. C. D., Gross V. P., and Murray K. D., “Suppression of particle generation in a modified clean room corona air ionizer,” Journal of Aerosol Science, vol. 21, no. 3, pp. 463–465, 1990
25
Hagbom M., Nordgren J., Nybom R., Hedlund K.-O., Wigzell H., and Svensson L., “Ionizing air affects influenza virus infectivity and prevents airborne-transmission,” Scientific Reports, vol. 5, no. 1, article 11431, 2015
26
Holt P. S., Mitchell B. W., Seo K.-H., and Gast R. K., “Use of negative air ionization for reducing airborne levels of Salmonella enterica serovar enteritidis in a room containing infected caged layers,” Journal of Applied Poultry Research, vol. 8, no. 4, pp. 440–446, 1999
27
Uk Lee B., Yermakov M., and Grinshpun S. A., “Removal of fine and ultrafine particles from indoor air environments by the unipolar ion emission,” Atmospheric Environment, vol. 38, no. 29, pp. 4815–4823, 2004
28
Mayya Y. S., Sapra B. K., Khan A., and Sunny F., “Aerosol removal by unipolar ionization in indoor environments,” Journal of Aerosol Science, vol. 35, no. 8, pp. 923–941, 2004
29
Grinshpun S. A., Mainelis G., Trunov M., Adhikari A., Reponen T., and Willeke K., “Evaluation of ionic air purifiers for reducing aerosol exposure in confined indoor spaces,” Indoor Air, vol. 15, no. 4, pp. 235–245, 2005
30
Berry D., Mainelis G., and Fennell D., “Effect of an ionic air cleaner on indoor/outdoor particle ratios in a residential environment,” Aerosol Science and Technology, vol. 41, no. 3, pp. 315–328, 2007
31
Qiu B., Li Q., Hong W., and Xing G., “Characterization of the Key Material for Elimination of PM2.5 Particles in the Atmosphere,” Journal of Spectroscopy, vol. 2015, –5, 2015
32
Sutton H. C., “Superoxide and ozone production by corona discharge,” Journal of the Chemical Society, Faraday Transactions 1: Physical Chemistry in Condensed Phases, vol. 80, no. 8, pp. 2301–2311, 1984
33
Pushpawela B., Jayaratne R., Nguy A., and Morawska L., “Efficiency of ionizers in removing airborne particles in indoor environments,” Journal of Electrostatics, vol. 90, pp. 79–84, 2017
34
Jiang S.-Y., Ma A., and Ramachandran S., “Negative Air Ions and Their Effects on Human Health and Air Quality Improvement,” International Journal of Molecular Sciences, vol. 19, no. 10, article 2966, 2018
35
Jiang S. Y., Ma A., and Ramachandran S. Indoor Air, 2020, ina.12729.
36
Kubala E., Strzelecka P., Grzegocka M., Lietz-Kijak D., Gronwald H., Skomro P., and Kijak E., “A Review of Selected Studies That Determine the Physical and Chemical Properties of Saliva in the Field of Dental Treatment,” BioMed Research International, vol. 2018, –13, 2018
37
Lin X., Ma W., Chen L., Huang L., Wu H., and Takahara A., “Influence of water evaporation/absorption on the stability of glycerol–water marbles,” RSC Advances, vol. 9, no. 59, pp. 34465–34471, 2019
38
Yang S., Lee G. W. M., Chen C. M., Wu C. C., and Yu K. P., “The size and concentration of droplets generated by coughing in human subjects,” Journal of Aerosol Medicine, vol. 20, no. 4, pp. 484–494, 2007
39
Zuo Z., Wang J., Huo Y., and Xu R., “Characteristics of particles deposited on a single free-fall charged droplet,” Aerosol Science and Technology, vol. 51, no. 3, pp. 258–268, 2017
40
Li W., and Davis E. J., “Aerosol evaporation in the transition regime,” Aerosol Science and Technology, vol. 25, no. 1, pp. 11–21, 1996
41
Chang R., and Davis E. J., “Knudsen aerosol evaporation,” Journal of Colloid and Interface Science, vol. 54, no. 3, pp. 352–363, 1976
42
Singh R., and Dewan A., “Rethinking use of individual room air-conditioners in view of COVID 19,” Creative Space, vol. 8, no. 1, pp. 15–20, 2020
43
Zhou C., Zhan Y., Chen S., Xia M., Ronda C., Sun M., Chen H., and Shen X., “Combined effects of temperature and humidity on indoor VOCs pollution: intercity comparison,” Building and Environment, vol. 121, pp. 26–34, 2017
44
Bradley D. T., Mansouri M. A., Kee F., and Garcia L. M. T. EClinicalMedicine, vol. 21, 2020
45
U. S. Department of Health, H. Services, and C. for Disease Control Guidelines for Environmental Infection Control in Health-Care Facilities Recommendations of CDC and the Healthcare Infection Control Practices Advisory Committee (HICPAC), 2019
Appendix
Less
Year 2021 volume 2021 Issue 2
PDF
84
45
Cite this Article
BibTeX
Article Info
doi: 10.34133/2021/2173642
  • Receive Date：2020-12-07
  • Online Date：2026-10-27
  • Published：2021-02-20
Article Data
Affiliations
History
  • Received：2020-12-07
  • Accepted：2020-12-29
Funding
A*STAR, Singapore(SC25/20-8R1640)
Affiliations
    1Institute of Materials Research and Engineering, 2 Fusionopolis Way, Agency for Science, Technology and Research, Singapore, 138634
    2Institute of High Performance Computing, 1 Fusionopolis Way, Agency for Science, Technology and Research, Singapore, 138632
    3Temasek Life Sciences Laboratory, 1 Research Link, National University of Singapore, Singapore, 117604
References
Share
https://castjournals.cast.org.cn/joweb/research/EN/10.34133/2021/2173642
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family		 属数
Number of
genus		 种数
Number of
species		 占总种数比例
Percentage of
total species (%)		 属
Genus		 种数
Number of
species		 占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT
Links
Articles
Latest Articles
Most Read
Collections
Updates
Events
News
Multimedia
About
About Us
Contact
No. 86 Xueyuan South Road, Haidian District, Beijing
100081
010-62662699(Operation and Technical Support)
qkjq@cast.org.cn

Copyright © 2025 China Association for Science and Technology. All rights reserved. For all open access content, the relevant licensing terms apply.
Sponsored by the Office of the Leading Group for Cybersecurity and Informatization of CAST, and supported by Science and Technology Review Publishing House