Home Journals Articles Updates About
CN
image
收藏切换
One-Step High-Temperature-Synthesized Single-Atom Platinum Catalyst for Efficient Selective Hydrogenation
收藏切换
PDF
Qingyuan Bi1, Xiaotao Yuan2, Yue Lu3, Dong Wang1, Jian Huang1, Rui Si4, Manling Sui3, Fuqiang Huang1, 2
Research. Vol 2020 Article ID 9140841
Less
收藏切换
Research. Vol 2020 Article ID 9140841
• Research Article •
One-Step High-Temperature-Synthesized Single-Atom Platinum Catalyst for Efficient Selective Hydrogenation
Full
Qingyuan Bi1, Xiaotao Yuan2, Yue Lu3, Dong Wang1, Jian Huang1, Rui Si4, Manling Sui3, Fuqiang Huang1, 2
Affiliations
  • 1State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050, China
  • 2State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, China
  • 3Institute of Microstructure and Properties of Advanced Materials, Beijing University of Technology, Beijing 100124, China
  • 4Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800, China
About Author:

Authors’ Contributions

Q. Bi, X. Yuan, and Y. Lu contributed equally to this work. Q. Bi and F. Huang conceived the research. Q. Bi, X. Yuan, D. Wang, and J. Huang contributed to the catalyst preparation, experimental measurements, and data analysis. Y. Lu and M. Sui performed the aberration-corrected STEM-HAADF. R. Si provided experimental guidance for the FT-EXAFS and XANES spectra. Q. Bi and X. Yuan wrote the paper. All authors reviewed and commented on the manuscript before publication.

Published: 2020-04-20 doi: 10.34133/2020/9140841
Outline
收藏切换

Although single-atom catalysts significantly improve the atom utilization efficiency, the multistep preparation procedures are complicated and difficult to control. Herein, we demonstrate that one-step in situ synthesis of the single-atom Pt anchored in single-crystal MoC (Pt1/MoC) by using facile and controllable arc-discharge strategy under extreme conditions. The high temperature (up to 4000°C) provides the sufficient energy for atom dispersion and overall stability by forming thermodynamically favourable metal-support interactions. The high-temperature-stabilized Pt1/MoC exhibits outstanding performance and excellent thermal stability as durable catalyst for selective quinoline hydrogenation. The initial turnover frequency of 3710 h-1 is greater than those of previously reported samples by an order of magnitude under 2 MPa H2 at 100°C. The catalyst also shows broad scope activity toward hydrogenation containing unsaturated groups of C=C, C=N, and C=O. The facile, one-step, and fast arc-discharge method provides an effective avenue for single-atom catalyst fabrication that is conventionally challenging.

Qingyuan Bi, Xiaotao Yuan, Yue Lu, Dong Wang, Jian Huang, Rui Si, Manling Sui, Fuqiang Huang. One-Step High-Temperature-Synthesized Single-Atom Platinum Catalyst for Efficient Selective Hydrogenation[J]. Research, 2020 , 2020 (4) : 9140841 - . DOI: 10.34133/2020/9140841
Full Text
Less
1. 　Introduction
Less
Single-atom catalysts (SACs) with unique electronic/geometric structures exhibit more effective atom utilization and can act as a promising bridge between homogeneous and heterogeneous catalysis [1–14]. The stability of SACs is a critical issue for their practical applications [15–17]. It was reported that the presence of subnanometer clusters in SACs can affect the overall thermal stability [18–23]. Tremendous efforts are made to improve the thermal stability by enhancing the metal-support interactions [1–17]. Currently, most SACs are prepared by the confinement and coordination of active metal atoms to the defective substrates via adsorption [24, 25], coprecipitation [1, 26], atomic layer deposition [27], galvanic replacement [28–30], and ionic exchange [11, 31] under mild conditions. However, the multistep procedures and complicated processes generally breed the inevitable difficulty in precise controlling of the atomic dispersion. It can also lead to the waste of resources and the generation of environmentally unfriendly by-products. Most recently, high-temperature-assisted routes (e.g., pyrolysis, fusion, and high-temperature shockwave) have been successfully utilized to synthesize the SACs and attract ever-increasing attention [32–36]. It was widely accepted that high temperature can significantly facilitate the formation of metal-support bonds or enhance the metal-atom-support interactions and thus result in excellent thermal stability [32–36]. Nevertheless, high-temperature (>3000°C) synthesis of SACs remains a challenge.
Herein, we present the use of high-temperature arc discharge to directly synthesize and stabilize platinum (Pt) single atoms in molybdenum carbide (MoC) substrate at ultrahigh temperatures (up to 4000°C). Compared to the traditional metal oxides, MoC shows excellent electrical conductivity which is beneficial for the electron transfer between active Pt sites and substrate and the formation of unique electronic/geometric structures. In contrast to the previously reported results [37], our MoC substrate is a typical single crystal with a small particle size. The high-temperature arc-discharge process provides sufficient activation energy for the formation of MoC substrate and strong Pt-MoC interactions, which is critical to achieve the Pt single-atom dispersion for overall stability in practical applications. This facile one-step synthesis strategy under extreme conditions can avoid the uncontrollable factors generally existing in conventional multistep procedures and largely shorten the preparation time to only tens of minutes. The high-temperature-stabilized single-atom Pt catalyst (Pt1/MoC) shows outstanding performance and excellent stability for the selective hydrogenation reaction, which is a key process for the synthesis of drugs, dyes, agrochemicals, and many biologically active intermediates [38–44]. Importantly, Pt1/MoC exhibits a turnover frequency (TOF) greater than those of existing catalysts by an order of magnitude in quinoline hydrogenation under mild conditions. Furthermore, the versatile Pt SAC shows a broad scope activity toward selective hydrogenation containing unsaturated groups of C=C, C=N, and C=O.
2. 　Results and Discussion
Less
MoC and Pt/MoC were synthesized via the facile one-step high-temperature arc-discharge strategy (Figures 1(a) and S1) [45, 46]. Note that the arc discharge process only takes tens of minutes (Figure S2), which can largely shorten the overall preparation time. As depicted in Figures 1(b) and 1(c), the pure single-crystal MoC with a considerable specific surface area (Figure S3 and Table S1) was readily obtained. The Pt nanoparticles (NPs) and even Pt single atom in MoC were also in situ formed, as shown in Figures 1(d)–1(g). X-ray diffraction (XRD) patterns presented in Figure S4 clearly show the exclusive presence of MoC phase with the face-centered-cubic α-MoC structure [37]. The absence of any Pt-containing phases indicates the high dispersion of Pt species. High-resolution transmission electron microscopy (HRTEM) data of 1% Pt/MoC (Figure S5) demonstrates the formation of small Pt NPs with a diameter of 2.2±0.2 nm. Clearly, the particle size decreases with the Pt loading decreasing. No appearance of Pt NPs was observed in Pt1/MoC. High-angle annular dark field- (HAADF-) scanning transmission electron microscopy (STEM) combined with energy-dispersive spectroscopy (EDS) reveals the formation of atomic Pt in Pt1/MoC (Figures 1(d), 1(e), and S6). Aberration-corrected STEM-HAADF images exhibit direct observation of the Pt single atoms (Figures 1(f) and S7). Pt dopant gave no change on the single crystal nature of matrix (inset in Figure 1(f)), and the isolated Pt atoms were tenaciously anchored in MoC substrate. To further verify the atomically dispersed Pt in Pt1/MoC, Fourier transform-extended X-ray absorption fine structure (FT-EXAFS) spectra were performed (Figures 1(g), S8, and S9 and Table S2). Only one notable peak at ca. 2 Å from the Pt-O contribution is observed, and no signal in the region 2.5 to 3 Å from the Pt-Pt contribution appears, indicative of the sole presence of single-atom Pt in Pt1/MoC (Table S2) [1, 37].
X-ray photoelectron spectroscopy (XPS) data of Mo 3d for Pt1/MoC catalyst demonstrates that Mo exists in Mo4+ and Mo2+ states (Figure 2(a)). Pt 4f XPS depicted in Figures 2(b) and S10 show that the atomically dispersed Pt is in the Ptδ+ state, indicative of the unique electron structure of Pt single atoms in Pt1/MoC [1, 37]. Normalized X-ray absorption near-edge structure (XANES) spectra at the Pt L-edge of Pt/MoC show a visible blue-shift from Pt foil to Pt1/MoC (Figure 2(c)), indicating that the Pt single atoms in Pt1/MoC possess positive charges in ambient atmosphere. In situ diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) was conducted to detect the CO chemical adsorption on Pt/MoC (Figure 2(d)). The band at 2090 cm-1 is ascribed to CO linearly adsorbed on Pt NPs in 2% Pt/MoC. As Pt size decreases, significant blueshift occurs for CO adsorption (2093 and 2101 cm-1 for 1% Pt/MoC and 0.2% Pt/MoC, respectively). The band at 2110 cm-1 is assigned to CO adsorbed on atomically dispersed Pt species, further confirming the fine isolation of Pt atoms in Pt1/MoC catalyst [1–3, 37].
Quinoline hydrogenation was selected as a model reaction to evaluate the catalytic activity of Pt/MoC. All the Pt/MoC catalysts were found to be highly efficient for selective quinoline hydrogenation under 2 MPa H2 at 100°C, as the selectivity of >99% to 1,2,3,4-tetrahydroquinoline listed in Table 1. No trace of frequently generated by-products like 5,6,7,8-tetrahydroquinoline or decahydroquinoline was observed. As Pt size decreases, the average TOF significantly increases from 393 h-1 for 2% Pt/MoC to 766 h-1 for 1% Pt/MoC to 1921 h-1 for 0.2% Pt/MoC (Table 1, entries 1-4). Remarkably, Pt1/MoC shows outstanding average TOF of 3380 h-1 (initial TOF of 3710 h-1) and near full conversion (>99%) for quinoline transformation (entries 5 and 6). Noteworthy, the exceptional TOF is greater than those of previously reported catalysts by an order of magnitude for quinoline hydrogenation under mild conditions (Table S3) [42–44, 47–49]. Pt1/MoC can also achieve selective reaction at low temperature of 60°C (entry 7) or under low H2 pressure of 1 MPa (entry 8). For the Pt catalysts with similar loading and comparable particle size (Figure S11) tested, the use of MoC rather than NbC, WC, and TiC as the most suitable support can significantly stimulate the catalysis potential of Pt (entries 9-11). In contrast, Pd, Ru, and Au with an identical size on MoC (Figure S11) show low efficiency for 1,2,3,4-tetrahydroquinoline synthesis. Only the catalysts based on Pt could deliver the high activity and provide the intrinsic advantages (entries 12-14). Compared to the one-step high-temperature strategy, Pt/MoC prepared by the conventional impregnation method (Figure S12) displays lower activity with the average TOF of 659 h-1 (entry 15). The commonly used Au/TiO2 (Figure S13) [40, 43, 50] exhibits very low activity with the selectivity of 75.9% (entry 16). Blank experiments without catalyst or use of Pt-free MoC show no conversion further confirming the indispensable role of Pt species for the desired transformation.
To examine whether the Pt-catalyzed reaction indeed occurred on the surface of Pt1/MoC, the solid was removed from the reaction system after 2 h. Postprocessing of the filtrate under identical conditions for another 2 h did not increase the conversion. Furthermore, the inductively coupled plasma atomic emission spectroscopy (ICP-AES) data of the filtrate shows that the content of Pt or Mo in the solution is below the detection limit of 0.1 ppm, indicating the leaching is negligible during the reaction and the heterogeneous catalysis nature of Pt1/MoC. The apparent activation energy (Ea) was estimated to be 32.42 kJ mol-1 (Figure S14), which is lower than those of the existing catalysts [42–44, 47–49]. Pt1/MoC can be reused at least for six runs without significant decay (Figure S15), indicative of the excellent stability for quinoline transformation. Compared to the fresh Pt1/MoC, no visible changes in the morphology, single crystal nature, and surface chemical state of Pt species of the used Pt1/MoC were observed and no aggregation of the Pt single atoms occurred (Figures S8, S9, S10, and S16–18 and Table S2). These results demonstrate the effectiveness of Pt1/MoC catalyst for selective quinoline hydrogenation.
Moreover, Pt1/MoC was extended to the investigation of various structurally different substituted quinoline compounds, as listed in Table 2. Reactions involving a methyl group at the 2- and 4-position proceeded smoothly to produce the corresponding 1,2,3,4-tetrahydroquinolines (Table 2, entries 1 and 2). The 2-position substrate was easily hydrogenated with higher average TOF of 2102 h-1 (initial TOF of 2522 h-1). Low performance for 2-methyl-4-hydroxyquinoline was obtained (entry 3) probably due to both steric and electronic effects [42, 50, 51]. For more challenging reaction involving reducible halogen groups (e.g., -Cl and -F), Pt1/MoC shows significant activities without any dehalogenation (entries 4 and 5). Interestingly, Pt1/MoC achieves the hydrogenation of isoquinoline with high selectivity (>99%) and moderate conversion (81.3%) (entry 6). Furthermore, Pt1/MoC could conduct the tentative experiment of heteroaromatic indole reduction, an important process in pharmaceutical synthesis [52], in spite of the low efficiency (entry 7).
The correlation between Pt1–MoC interactions and performance of Pt1/MoC catalyst for quinoline hydrogenation was further studied to gain insights into the reaction mechanism. Primary kinetic isotope effects (KIEs) with H2 being labeled using HD or D2 are summarized in Table S4 and Figure 3(a). HD and D2 show significant KIEs in the reduction process, and the latter exhibits larger value of 5.1. These results indicate that the cleavage of H-H bond and the formation of C-C and C-N bonds in pyridine ring are kinetically relevant steps in quinoline hydrogenation [47]. In order to probe the potential key intermediates under the presence of D2 over surface positively charged Pt1/MoC, quasi in situ Fourier transform infrared (FTIR) spectroscopy was conducted. The IR vibration of O–D bond at 2550 cm-1 was clearly observed (Figure 3(b)), and the heterolytic dissociation of H2 was promoted by temperature, forming O–D(δ+) and Pt–D(δ–) species. Besides the intrinsic effect of the atomically dispersed Pt species, MoC as a conductor can also facilitate the H2 activation and dissociation [37], and the suitable Pt–MoC interactions are beneficial for these key steps. Note that the rate of H2 activation and dissociation was much faster than that of the overall process of hydrogenation [43, 47]. Thus, the rate-determining step (RDS) can be derived from the subsequent hydrogenation with one hydrogen transfer from Pt–H(δ–) and another from O–H(δ+) to the pyridine ring.
Based on the catalytic performance, KIEs, and FTIR results, a possible reaction pathway for selective quinoline hydrogenation over Pt1/MoC was proposed (Figure 3(c)). The hydrogenation process may consist of the following four steps: (i) initial adsorption and chemical activation of H2 molecules over the positively charged Pt with heterolytic dissociation forming Pt–H(δ–) and O–H(δ+) species; (ii) chemisorption of quinoline molecules on the catalyst surface primarily through the Pt-N interaction, thus facilitating the activation of pyridine ring; (iii) generation of the adsorbed 1,2,3,4-tetrahydroquinoline via the transfer of H(δ–) and H(δ+) intermediates to the activated pyridine ring; and (iv) desorption of the goal product 1,2,3,4-tetrahydroquinoline from the catalyst surface. The adsorption and/or chemical activation of H2 and quinoline molecules are widely considered to be the kinetically relevant step and pyridine ring hydrogenation as the RDS [47]. Although considerable amount of energy is required for quinoline hydrogenation, the appropriate interaction of Pt-N (Pt1/MoC-quinoline) and the strong interactions between positively charged Pt atoms and MoC substrate could efficiently surpass the total reaction barriers and achieve the formation of desired 1,2,3,4-tetrahydroquinoline.
Pt1/MoC was further examined for selective hydrogenation of α,β-unsaturated aldehyde involving C=C and C=O groups [39, 53–57]. The SAC exhibits a high efficiency with the average TOF of 1216 h-1 for crotonaldehyde hydrogenation (Table S5). This is the best performance reported for crotonaldehyde hydrogenation via heterogeneous catalysis under identical conditions and is comparable with most values gained using organic complexes [53–55]. Similar to quinoline hydrogenation, crotonaldehyde conversion using Pt NPs leads to less efficiencies (Table S5). These results again demonstrate the remarkable benefit of using single-atom Pt catalyst for selective reduction of α,β-unsaturated aldehyde and further suggest the broad application prospects of Pt SAC in fine chemical synthesis.
3. 　Conclusion
Less
A facile and controllable one-step arc-discharge strategy at ultrahigh temperature was successfully developed to synthesize single-atom Pt catalyst. High-temperature-stabilized Pt1/MoC with a unique electronic/geometric structure exhibits outstanding performance and excellent thermal stability for selective quinoline hydrogenation. The activity of 3710 h-1 is better than those of previously reported catalysts by an order of magnitude under similar conditions. Pt1/MoC shows broad scope activity toward hydrogenation including quinoline compounds and crotonaldehyde containing C=C, C=N, and C=O groups. Primary kinetic isotope effects and in situ FTIR analysis show that the cleavage of H-H bond and the formation of C-C and C-N bonds in pyridine ring over the positively charged Pt1/MoC are kinetically relevant steps and the latter is RDS. The possible four-step mechanism involving the heterolytic dissociation of H2 and the transfer of H(δ-) and H(δ+) species to the activated pyridine ring via Pt-N bond over Pt1/MoC is proposed. We anticipate that the one-step high-temperature strategy will allow the development of broad SACs for the important yet challenging chemical transformations.
4. 　Materials and Methods
Less
4.1. 　Preparation of MoC
The MoC was synthesized by a direct current arc-discharge method (Figures 1 and S1) [45, 46]. The cathode was a pure graphite rod with a diameter of 8 mm. The anode was a graphite tube with an external diameter of 8 mm and an inner diameter of 6 mm. The graphite tube was filled with Mo powders. The two electrodes were installed horizontally, and the cathode was fixed on a water-cooled copper pedestal. The arc chamber was first evacuated to 3 Pa and then filled by pure H2 to the pressure of 0.08 MPa. The arc was generated at a current of 80 A, and the distance between the two electrodes was kept at about 2 mm by physically adjusting the cathode. The typical synthesis time was about 30 min, and about 1 cm anode was consumed. After reaction, the powders generated on the top of the arc chamber were collected.
4.2. 　Preparation of Pt/MoC Catalysts
In analogy to the case with MoC, the Pt/MoC catalysts were one-step in situ prepared by the arc-discharge method. The graphite tube, which was filled with a mixture of Pt and Mo powders, was used as anode. The mass fraction of Pt in the mixture depends on the mass loading of Pt in the final Pt/MoC product. By controlling the Pt loading, the Pt1/MoC can be easily achieved.
4.3. 　Catalyst Characterization
XRD characterization of the samples was carried out on a German Bruker D8 Advance X-ray diffractometer using the Ni-filtered Cu Kα radiation at 40 kV and 40 mA. XPS data were recorded with the Axis Ultra Photoelectron Spectrometer (Kratos Analytical Ltd.) by means of a monochromatized Al Kα anode (225 W, 15 mA, 15 kV). The C 1s peak at 284.8 eV was used as the reference to calibrate the binding energies (BE). A Tecnai F20 electron microscope operating at 200 kV equipped with an EDS unit (Si(Li) detector) was used for the TEM investigations. The samples for electron microscopy were prepared by grinding and subsequent dispersing the powder in ethanol and applying a drop of very dilute suspension on carbon-coated grids. High resolution TEM, EDS mapping, and HADDF-STEM were performed on an FEI Titan G2 (60-300) probe-corrected TEM system with a field emission gun operated at 300 kV.
4.4. 　Catalytic Activity Test
The selective hydrogenations were carried out in a high-pressure stainless autoclave reactor (Parr Instrument Co., 4790, 50 mL). Typically, 2 mL solvent (toluene or ethanol), a certain amount of substrate (quinoline or quinoline compounds or crotonaldehyde), and a known amount of catalyst were placed in the autoclave. The autoclave was sealed and flushed several times with 0.5 MPa H2 to remove the air in the reactor; then, 2 MPa H2 was charged. The stirrer (800 rpm) was started until the desired temperature was reached. After a certain time, the autoclave was placed in cool water and the gas was carefully released. The gaseous mixture was analyzed using a gas chromatograph (GC) Agilent 7820A equipped with a TDX-01 column connected to a thermal conductivity detector. A known amount of internal standard 1,4-dioxane was added into the aqueous product in autoclave. The reaction mixture was transferred into a centrifuge tube, and the solid catalyst was separated by centrifugation. The product solution was quantitatively analyzed using a GC Agilent 7820A equipped with a HP-5 capillary column connected to a flame ionization detector. Identification of the products was performed by using a GC-MS spectrometer. Noted that the total carbon balance was >95%. For the recycling experiment, the centrifuged catalysts from parallel tests were collected and washed with distilled water several times, followed by air drying at 120°C for 12 h. The KIE experiments were performed by following the same procedure as selective hydrogenations. The H2 or HD or D2 was, respectively, used as hydrogen source. The products were qualitatively and quantitatively analyzed using a GC and GC-MS spectrometer. The conversions of quinoline were kept below 20% for calculation of initial TOF. The unit of TOF is h-1, that is, mol target product per mol noble metal site per hour.
Funding
Less
  • Chinese Academy of Sciences(KGZD-EW-T06; QYZDJ-SSW-JSC013)
  • National Natural Science Foundation of China(21872166)
  • National Key Research and Development Program of China(2016YFB0901600)
References
Less
1
Qiao B., Wang A., Yang X., Allard L. F., Jiang Z., Cui Y., Liu J., Li J., and Zhang T., “Single-atom catalysis of CO oxidation using Pt1/FeO _x_,” Nature Chemistry, vol. 3, no. 8, pp. 634–641, 2011
2
Ding K., Gulec A., Johnson A. M., Schweitzer N. M., Stucky G. D., Marks L. D., and Stair P. C., “Identification of active sites in CO oxidation and water-gas shift over supported Pt catalysts,” Science, vol. 350, no. 6257, pp. 189–192, 2015
3
Nie L., Mei D., Xiong H., Peng B., Ren Z., Hernandez X. I. P., DeLaRiva A., Wang M., Engelhard M. H., Kovarik L., Datye A. K., and Wang Y., “Activation of surface lattice oxygen in single-atom Pt/CeO2 for low-temperature CO oxidation,” Science, vol. 358, no. 6369, pp. 1419–1423, 2017
4
He T., Chen S., Ni B., Gong Y., Wu Z., Song L., Gu L., Hu W., and Wang X., “Zirconium–porphyrin-based metal–organic framework hollow nanotubes for immobilization of noble-metal single atoms,” Angewandte Chemie International Edition, vol. 57, no. 13, pp. 3493–3498, 2018
5
Liu L., and Corma A., “Metal catalysts for heterogeneous catalysis: from single atoms to nanoclusters and nanoparticles,” Chemical Reviews, vol. 118, no. 10, pp. 4981–5079, 2018
6
Wang A., Li J., and Zhang T., “Heterogeneous single-atom catalysis,” Nature Reviews Chemistry, vol. 2, no. 6, pp. 65–81, 2018
7
Cui X., Li W., Ryabchuk P., Junge K., and Beller M., “Bridging homogeneous and heterogeneous catalysis by heterogeneous single- metal-site catalysts,” Nature Catalysis, vol. 1, no. 6, pp. 385–397, 2018
8
Liu P., Zhao Y., Qin R., Mo S., Chen G., Gu L., Chevrier D. M., Zhang P., Guo Q., Zang D., Wu B., Fu G., and Zheng N., “Photochemical route for synthesizing atomically dispersed palladium catalysts,” Science, vol. 352, no. 6287, pp. 797–800, 2016
9
Zhang X., Sun Z., Wang B., Tang Y., Nguyen L., Li Y., and Tao F. F., “C–C coupling on single-atom-based heterogeneous catalyst,” Journal of the American Chemical Society, vol. 140, no. 3, pp. 954–962, 2018
10
Shan J., Li M., Allard L. F., Lee S., and Flytzani-Stephanopoulos M., “Mild oxidation of methane to methanol or acetic acid on supported isolated rhodium catalysts,” Nature, vol. 551, no. 7682, pp. 605–608, 2017
11
Li Z., Wang D., Wu Y., and Li Y., “Recent advances in the precise control of isolated single-site catalysts by chemical methods,” National Science Review, vol. 5, no. 5, pp. 673–689, 2018
12
Jakub Z., Hulva J., Meier M., Bliem R., Kraushofer F., Setvin M., Schmid M., Diebold U., Franchini C., and Parkinson G. S., “Local structure and coordination define adsorption in a model Ir1/Fe3O4Single‐Atom catalyst,” Angewandte Chemie, vol. 131, no. 39, pp. 14099–14106, 2019
13
Hoffman A. S., Debefve L. M., Zhang S., Perez-Aguilar J. E., Conley E. T., Justl K. R., Arslan I., Dixon D. A., and Gates B. C., “Beating heterogeneity of single-site catalysts: MgO-supported iridium complexes,” ACS Catalysis, vol. 8, no. 4, pp. 3489–3498, 2018
14
Meng D.-L., Chen C.-H., Yi J.-D., Wu Q., Liang J., Huang Y. B., and Cao R., “Migration-prevention strategy to fabricate single-atom Fe implanted N-doped porous carbons for efficient oxygen reduction,” Research, vol. 2019, article 1768595, pp. 1–12, 2019
15
Zhang Z., Zhu Y., Asakura H., Zhang B., Zhang J., Zhou M., Han Y., Tanaka T., Wang A., Zhang T., and Yan N., “Thermally stable single atom Pt/m-Al2O3 for selective hydrogenation and CO oxidation,” Nature Communications, vol. 8, no. 1, p. 16100, 2017
16
Hansen T. W., Delariva A. T., Challa S. R., and Datye A. K., “Sintering of catalytic nanoparticles: particle migration or Ostwald ripening?,” Accounts of Chemical Research, vol. 46, no. 8, pp. 1720–1730, 2013
17
Jones J., Xiong H., DeLaRiva A. T., Peterson E. J., Pham H., Challa S. R., Qi G., Oh S., Wiebenga M. H., Pereira Hernandez X. I., Wang Y., and Datye A. K., “Thermally stable single-atom platinum-on-ceria catalysts via atom trapping,” Science, vol. 353, no. 6295, pp. 150–154, 2016
18
Yu K., Xu T., Wu X., Wang W., Zhang H., Zhang Q., Tang L., and Sun L., “In situ observation of crystalline silicon growth from SiO2at atomic scale,” Research, vol. 2019, article 3289247, pp. 1–9, 2019
19
Liu L., Meira D. M., Arenal R., Concepcion P., Puga A. V., and Corma A., “Determination of the evolution of heterogeneous single metal atoms and nanoclusters under reaction conditions: which are the working catalytic sites?,” ACS Catalysis, vol. 9, no. 12, pp. 10626–10639, 2019
20
Kuo C.-T., Lu Y., Kovarik L., Engelhard M., and Karim A. M., “Structure sensitivity of acetylene semi-hydrogenation on Pt single atoms and subnanometer clusters,” ACS Catalysis, vol. 9, no. 12, pp. 11030–11041, 2019
21
Resasco J., Yang F., Mou T., Wang B., Christopher P., and Resasco D. E., “Relationship between atomic scale structure and reactivity of Pt catalysts: hydrodeoxygenation ofm-Cresol over isolated Pt cations and clusters,” ACS Catalysis, vol. 10, no. 1, pp. 595–603, 2020
22
DeRita L., Dai S., Lopez-Zepeda K., Pham N., Graham G. W., Pan X., and Christopher P., “Catalyst architecture for stable single atom dispersion enables site-specific spectroscopic and reactivity measurements of CO adsorbed to Pt atoms, oxidized Pt clusters, and metallic Pt clusters on TiO2,” Journal of the American Chemical Society, vol. 139, no. 40, pp. 14150–14165, 2017
23
Resasco J., DeRita L., Dai S., Chada J. P., Xu M., Yan X., Finzel J., Hanukovich S., Hoffman A. S., Graham G. W., Bare S. R., Pan X., and Christopher P., “Uniformity is key in defining structure−function relationships for atomically dispersed metal catalysts: the case of Pt/CeO2,” Journal of the American Chemical Society, vol. 142, no. 1, pp. 169–184, 2020
24
Yang M., Li S., Wang Y., Herron J. A., Xu Y., Allard L. F., Lee S., Huang J., Mavrikakis M., and Flytzani-Stephanopoulos M., “Catalytically active Au-O(OH)x-species stabilized by alkali ions on zeolites and mesoporous oxides,” Science, vol. 346, no. 6216, pp. 1498–1501, 2014
25
Moliner M., Gabay J. E., Kliewer C. E., Carr R. T., Guzman J., Casty G. L., Serna P., and Corma A., “Reversible transformation of Pt nanoparticles into single atoms inside high-silica chabazite zeolite,” Journal of the American Chemical Society, vol. 138, no. 48, pp. 15743–15750, 2016
26
Lin J., Wang A., Qiao B., Liu X., Yang X., Wang X., Liang J., Li J., Liu J., and Zhang T., “Remarkable performance of Ir1/FeOxSingle-Atom catalyst in water gas shift reaction,” Journal of the American Chemical Society, vol. 135, no. 41, pp. 15314–15317, 2013
27
Yan H., Cheng H., Yi H., Lin Y., Yao T., Wang C., Li J., Wei S., and Lu J., “Single-atom Pd1/graphene catalyst achieved by atomic layer deposition: remarkable performance in selective hydrogenation of 1,3-butadiene,” Journal of the American Chemical Society, vol. 137, no. 33, pp. 10484–10487, 2015
28
Marcinkowski M. D., Darby M. T., Liu J., Wimble J. M., Lucci F. R., Lee S., Michaelides A., Flytzani-Stephanopoulos M., Stamatakis M., and Sykes E. C. H., “Pt/Cu single-atom alloys as coke-resistant catalysts for efficient C–H activation,” Nature Chemistry, vol. 10, no. 3, pp. 325–332, 2018
29
Liu L., Díaz U., Arenal R., Agostini G., Concepción P., and Corma A., “Generation of subnanometric platinum with high stability during transformation of a 2D zeolite into 3D,” Nature Materials, vol. 16, no. 1, pp. 132–138, 2017
30
Yin P., Yao T., Wu Y., Zheng L., Lin Y., Liu W., Ju H., Zhu J., Hong X., Deng Z., Zhou G., Wei S., and Li Y., “Single cobalt atoms with precise N-coordination as superior oxygen reduction reaction catalysts,” Angewandte Chemie International Edition, vol. 55, no. 36, pp. 10800–10805, 2016
31
Zhao C., Dai X., Yao T., Chen W., Wang X., Wang J., Yang J., Wei S., Wu Y., and Li Y., “Ionic exchange of metal–organic frameworks to access single nickel sites for efficient electroreduction of CO2,” Journal of the American Chemical Society, vol. 139, no. 24, pp. 8078–8081, 2017
32
Wei S., Li A., Liu J. C., Li Z., Chen W., Gong Y., Zhang Q., Cheong W. C., Wang Y., Zheng L., Xiao H., Chen C., Wang D., Peng Q., Gu L., Han X., Li J., and Li Y., “Direct observation of noble metal nanoparticles transforming to thermally stable single atoms,” Nature Nanotechnology, vol. 13, no. 9, pp. 856–861, 2018
33
Wang X., Chen Z., Zhao X., Yao T., Chen W., You R., Zhao C., Wu G., Wang J., Huang W., Yang J., Hong X., Wei S., Wu Y., and Li Y., “Regulation of coordination number over single Co sites: triggering the efficient electroreduction of CO2,” Angewandte Chemie International Edition, vol. 57, no. 7, pp. 1944–1948, 2018
34
Qiu H.-J., Ito Y., Cong W., Tan Y., Liu P., Hirata A., Fujita T., Tang Z., and Chen M., “Nanoporous graphene with single-atom nickel dopants: an efficient and stable catalyst for electrochemical hydrogen production,” Angewandte Chemie International Edition, vol. 54, no. 47, pp. 14031–14035, 2015
35
Guo X., Fang G., Li G., Ma H., Fan H., Yu L., Ma C., Wu X., Deng D., Wei M., Tan D., Si R., Zhang S., Li J., Sun L., Tang Z., Pan X., and Bao X., “Direct, nonoxidative conversion of methane to ethylene, aromatics, and hydrogen,” Science, vol. 344, no. 6184, pp. 616–619, 2014
36
Yao Y., Huang Z., Xie P., Wu L., Ma L., Li T., Pang Z., Jiao M., Liang Z., Gao J., He Y., Kline D. J., Zachariah M. R., Wang C., Lu J., Wu T., Li T., Wang C., Shahbazian-Yassar R., and Hu L., “High temperature shockwave stabilized single atoms,” Nature Nanotechnology, vol. 14, no. 9, pp. 851–857, 2019
37
Lin L., Zhou W., Gao R., Yao S., Zhang X., Xu W., Zheng S., Jiang Z., Yu Q., Li Y. W., Shi C., Wen X. D., and Ma D., “Low-temperature hydrogen production from water and methanol using Pt/α-MoC catalysts,” Nature, vol. 544, no. 7648, pp. 80–83, 2017
38
Nishimura S. Handbook of Heterogeneous Catalytic Hydrogenation for Organic Synthesis, Wiley-VCH, JOHN WILEY & SONS, INC., 2001
39
Kennedy G., Baker L. R., and Somorjai G. A., “Selective amplification of C=O bond hydrogenation on Pt/TiO₂: catalytic reaction and sum-frequency generation vibrational spectroscopy studies of crotonaldehyde hydrogenation,” Angewandte Chemie International Edition, vol. 53, no. 13, pp. 3405–3408, 2014
40
Vilé G., Albani D., Almora-Barrios N., López N., and Pérez-Ramírez J., “Advances in the design of nanostructured catalysts for selective hydrogenation,” ChemCatChem, vol. 8, no. 1, pp. 21–33, 2016
41
Dobereiner G. E., Nova A., Schley N. D., Hazari N., Miller S. J., Eisenstein O., and Crabtree R. H., “Iridium-catalyzed hydrogenation of N-heterocyclic compounds under mild conditions by an outer-sphere pathway,” Journal of the American Chemical Society, vol. 133, no. 19, pp. 7547–7562, 2011
42
Wang X., Chen W., Zhang L., Yao T., Liu W., Lin Y., Ju H., Dong J., Zheng L., Yan W., Zheng X., Li Z., Wang X., Yang J., He D., Wang Y., Deng Z., Wu Y., and Li Y., “Uncoordinated amine groups of metal−organic frameworks to anchor single Ru sites as chemoselective catalysts toward the hydrogenation of quinoline,” Journal of the American Chemical Society, vol. 139, no. 28, pp. 9419–9422, 2017
43
Ren D., He L., Yu L., Ding R. S., Liu Y. M., Cao Y., He H. Y., and Fan K. N., “An unusual chemoselective hydrogenation of quinoline compounds using supported gold catalysts,” Journal of the American Chemical Society, vol. 134, no. 42, pp. 17592–17598, 2012
44
Tang M., Deng J., Li M., Li X., Li H., Chen Z., and Wang Y., “3D-interconnected hierarchical porous N-doped carbon supported ruthenium nanoparticles as an efficient catalyst for toluene and quinoline hydrogenation,” Green Chemistry, vol. 18, no. 22, pp. 6082–6090, 2016
45
Bi Q., Wang X., Gu F., du X., Bao H., Yin G., Liu J., and Huang F., “Prominent electron penetration through ultrathin graphene layer from FeNi alloy for efficient reduction of CO2 to CO,” ChemSusChem, vol. 10, no. 15, pp. 3044–3048, 2017
46
Wang C., Zhai P., Zhang Z., Zhou Y., Zhang J., Zhang H., Shi Z., Han R. P. S., Huang F., and Ma D., “Nickel catalyst stabilization via graphene encapsulation for enhanced methanation reaction,” Journal of Catalysis, vol. 334, no. 2, pp. 42–51, 2016
47
Bai L., Wang X., Chen Q., Ye Y., Zheng H., Guo J., Yin Y., and Gao C., “Explaining the size dependence in platinum-nanoparticle-catalyzed hydrogenation reactions,” Angewandte Chemie International Edition, vol. 55, no. 50, pp. 15656–15661, 2016
48
Mao H., Ma J., Liao Y., Zhao S., and Liao X., “Using plant tannin as natural amphiphilic stabilizer to construct an aqueous–organic biphasic system for highly active and selective hydrogenation of quinoline,” Catalysis Science & Technology, vol. 3, no. 6, pp. 1612–1617, 2013
49
Yan M., Jin T., Chen Q., Ho H. E., Fujita T., Chen L. Y., Bao M., Chen M. W., Asao N., and Yamamoto Y., “Unsupported nanoporous gold catalyst for highly selective hydrogenation of quinolines,” Organic Letters, vol. 15, no. 7, pp. 1484–1487, 2013
50
Tao L., Zhang Q., Li S. S., Liu X., Liu Y. M., and Cao Y., “Heterogeneous gold-catalyzed selective reductive transformation of quinolines with formic acid,” Advanced Synthesis & Catalysis, vol. 357, no. 4, pp. 753–760, 2015
51
Wei H., Liu X., Wang A., Zhang L., Qiao B., Yang X., Huang Y., Miao S., Liu J., and Zhang T., “FeOx-supported platinum single-atom and pseudo-single- atom catalysts for chemoselective hydrogenation of functionalized nitroarenes,” Nature Communications, vol. 5, no. 1, p. 5634, 2014
52
Zhao D., Shi Z., and Glorius F., “Indole synthesis by rhodium (III)-catalyzed hydrazine-directed C-H activation: redox-neutral and traceless by N-N bond cleavage,” Angewandte Chemie International Edition, vol. 52, no. 47, pp. 12426–12429, 2013
53
Wang M. M., He L., Liu Y. M., Cao Y., He H. Y., and Fan K. N., “Gold supported on mesostructured ceria as an efficient catalyst for the chemoselective hydrogenation of carbonyl compounds in neat water,” Green Chemistry, vol. 13, no. 3, pp. 602–607, 2011
54
Li C., Chen Y., Zhang S., Xu S., Zhou J., Wang F., Wei M., Evans D. G., and Duan X., “Ni−In intermetallic nanocrystals as efficient catalysts toward unsaturated aldehydes hydrogenation,” Chemistry of Materials, vol. 25, no. 19, pp. 3888–3896, 2013
55
Lin H., Zheng J., Zheng X., Gu Z., Yuan Y., and Yang Y., “Improved chemoselective hydrogenation of crotonaldehyde over bimetallic AuAg/SBA-15 catalyst,” Journal of Catalysis, vol. 330, no. 10, pp. 135–144, 2015
56
Zhao M., Yuan K., Wang Y., Li G., Guo J., Gu L., Hu W., Zhao H., and Tang Z., “Metal-organic frameworks as selectivity regulators for hydrogenation reactions,” Nature, vol. 539, no. 7627, pp. 76–80, 2016
57
Bai S., Bu L., Shao Q., Zhu X., and Huang X., “Multicomponent Pt-based zigzag nanowires as selectivity controllers for selective hydrogenation reactions,” Journal of the American Chemical Society, vol. 140, no. 27, pp. 8384–8387, 2018
Appendix
Less
Year 2020 volume 2020 Issue 4
PDF
49
28
Cite this Article
BibTeX
Article Info
doi: 10.34133/2020/9140841
  • Receive Date：2019-12-20
  • Online Date：2026-10-27
  • Published：2020-04-20
Article Data
Affiliations
History
  • Received：2019-12-20
  • Accepted：2020-03-22
Funding
Chinese Academy of Sciences(KGZD-EW-T06; QYZDJ-SSW-JSC013)
National Natural Science Foundation of China(21872166)
National Key Research and Development Program of China(2016YFB0901600)
Affiliations
    1State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 200050, China
    2State Key Laboratory of Rare Earth Materials Chemistry and Applications, College of Chemistry and Molecular Engineering, Peking University, Beijing 100871, China
    3Institute of Microstructure and Properties of Advanced Materials, Beijing University of Technology, Beijing 100124, China
    4Shanghai Synchrotron Radiation Facility, Shanghai Institute of Applied Physics, Chinese Academy of Sciences, Shanghai 201800, China
References
Share
https://castjournals.cast.org.cn/joweb/research/EN/10.34133/2020/9140841
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family		 属数
Number of
genus		 种数
Number of
species		 占总种数比例
Percentage of
total species (%)		 属
Genus		 种数
Number of
species		 占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT
Links
Articles
Latest Articles
Most Read
Collections
Updates
Events
News
Multimedia
About
About Us
Contact
No. 86 Xueyuan South Road, Haidian District, Beijing
100081
010-62662699(Operation and Technical Support)
qkjq@cast.org.cn

Copyright © 2025 China Association for Science and Technology. All rights reserved. For all open access content, the relevant licensing terms apply.
Sponsored by the Office of the Leading Group for Cybersecurity and Informatization of CAST, and supported by Science and Technology Review Publishing House