Home Journals Articles Updates About
CN
image
收藏切换
Multimaterial Embedded 3D Printing of Composite Reinforced Soft Actuators
收藏切换
PDF
Zhenhua Wang1, 2, Boyu Zhang2, 3, Qu He1, 2, Hao Chen1, 2, Jizhe Wang2, 3, Yuan Yao2, 3, Nanjia Zhou2, 3, *, Weicheng Cui1, 2, *
Research. Vol 6 Article ID 0122
Less
收藏切换
Research. Vol 6 Article ID 0122
• Research Article •
Multimaterial Embedded 3D Printing of Composite Reinforced Soft Actuators
Full
Zhenhua Wang1, 2, Boyu Zhang2, 3, Qu He1, 2, Hao Chen1, 2, Jizhe Wang2, 3, Yuan Yao2, 3, Nanjia Zhou2, 3, *, Weicheng Cui1, 2, *
Affiliations
  • 1Key Laboratory of Coastal Environment and Resources of Zhejiang Province, School of Engineering, Westlake University, Hangzhou, Zhejiang Province, China.
  • 2Institute of Advanced Technology, Westlake Institute for Advanced Study, Hangzhou, Zhejiang Province, China.
  • 3Research Center for Industries of the Future, and Key Laboratory of 3D Micro/Nano Fabrication and Characterization of Zhejiang Province, School of Engineering, Westlake University, Hangzhou, Zhejiang Province, China.
Published: 2023-04-20 doi: 10.34133/research.0122
Outline
收藏切换

Soft pneumatic actuators (SPAs) have attracted enormous attention in the growing field of robotics. Among different SPAs, composite reinforced actuators (CRAs) are widely used because of their simple structure and high controllability. However, multistep molding, a time-consuming method, is still the predominant fabrication method. Here, we propose a multimaterial embedded printing method (ME3P) to fabricate CRAs. In comparison with other 3-dimensional printing methods, our method improves fabrication flexibility greatly. Via the design and fabrication of the reinforced composites’ patterns and different geometries of the soft body, we demonstrate actuators with programmable responses (elongation, contraction, twisting, bending, and helical and omnidirectional bending). Finite element analysis is employed for the prediction of pneumatic responses and the inverse design of actuators based on specific actuation needs. Lastly, we use tube-crawling robots as a model system to demonstrate our ability to fabricate complex soft robots for practical applications. This work demonstrates the versatility of ME3P for the future manufacturing of CRA-based soft robots.

Zhenhua Wang, Boyu Zhang, Qu He, Hao Chen, Jizhe Wang, Yuan Yao, Nanjia Zhou, Weicheng Cui. Multimaterial Embedded 3D Printing of Composite Reinforced Soft Actuators[J]. Research, 2023 , 6 (4) : 0122 - . DOI: 10.34133/research.0122
Full Text
Less
Introduction
Less
Inspired by nature, soft actuators have attracted great attention for applications in delicate object manipulation, safe human–robot interactions, and medical robots for diagnosis and surgery thanks to their inherent mechanical compliance [1–5]. Among different types of soft actuators, soft pneumatic actuators (SPAs) present strong advantages in high workload, excellent reversibility and controllability, as well as fast actuation speed [6,7]. Soft composite reinforced actuators (CRAs), as a branch of SPAs, employ a combination of inextensible materials with soft elastomer materials, greatly expanding the actuator functionalities while still adopting simple geometries. Conventional CRAs are fabricated by wrapping the soft inflating materials (e.g., silicone rubber) with stiff fibers (Kevlar fiber [6–9], thermoplastic polyurethanes [10], resin [11,12], and others). Compared with other types of SPAs (especially PneuNet actuators [13]), CRAs feature simple structural design, uniform stress distribution, and convenient modeling and programming methods [14]. The fiber diameters, winding pitches, and orientations are readily programmable to design and manufacture application-specific actuators that enable complex motions [14].
Regarding the manufacturing of CRAs, multistep molding is the most used strategy [11,15,16]. However, it suffers from limited design freedom while requiring much manual intervention, which poses challenges in accurate assembly [10]. In addition, the winding of fibers on the soft inflating surface typically are limited to only simple patterns (fibers with different winding angle). Such methods are insufficient for CRAs with complex shape morphing ability, which are substantial for functional soft actuators [17,18]. Three-dimensional (3D) printing, as an emerging digital manufacturing approach, has been demonstrated for the rapid fabrication of CRAs with complex reinforced patterns. Most previous reports of 3D printed CRAs predominantly focus on the manual assembly of fiber layers with molded silicone elastomer bodies [11,19] printed typically via vat photopolymerization. These methods still involve inaccurate and time-consuming manual casting work. Also, the materials employed in vat photopolymerization are limited to light-curing materials (resins, hydrogels, and others) [20]. Direct ink writing (DIW), on the other hand, could overcome these problems to become a rapid and digital fabrication method for CRAs with wider material choices [10,21 ,22]. For example, Schaffner et al. [21] use DIW to print stiff fiber patterns with different orientation angles onto a layer of silicone on a rotating cylindrical shaft. Although fibers with various patterns can be fabricated, the overall geometries of the inflating bodies are highly restricted by the shape of the shaft. Embedded 3D printing, featuring printing the structural and functional inks in a common supporting matrix, could overcome such shape limitations [23,24], and it has been used to fabricate PneuNet actuators generating single motions [25–27] and fully functional robots based on them. However, implemented in the normal Cartesian machine coordinate system, embedded 3D printing faces challenges in the freeform patterning of fibers onto arbitrary 3D geometries. The fabrication of more complex pneumatics CRAs, e.g., the shape-morphing CRAs, demands the development of embedded 3D printable materials featuring different mechanical properties and improved multiaxis printing platform.
In this work, for the first time, we propose a novel multimaterial embedded 3D printing (ME3P) method for CRAs, which enables the monolithic design and manufacturing of arbitrary-shaped complex actuator bodies with inner channels as well as the facile patterning of complex reinforced materials on actuator surfaces. The mechanical and rheological properties of the hard, soft, and matrix materials are investigated to optimize the design and manufacturing of the CRAs. The process parameters of the ME3P are investigated to help understand the filament morphology to optimize the print quality and resolution. We demonstrate actuators with different reinforced composite patterns to generate programmable pneumatic responses. We also demonstrate the CRAs with shape morphing ability and local compliant mechanisms. A finite element analysis (FEA) data-driven method is utilized for the inverse design of actuators. Finally, 2 crawling robots capable of moving through forked tubes both in air and in water are printed as demonstrations.
Results and Discussion
Less
Printing method
The structure of our printing system is shown in Fig. 1A. For our first demonstration, we printed a pneumatic flower via a 2-step process (Fig. 1B and Movie S1): First, the soft ink was used to print flower petals with air channels (Fig. S1) in the matrix; second, the hard ink was conformally printed on both sides of the petals to control the shape morphing upon inflation. A rotary axis (U-axis) was added to print stiff reinforced patterns on the petal surfaces. The nozzle tip in step 2 was bent to 90° to ensure that it is perpendicular to the petal surfaces at the printing position (Fig. 1A and B). As reported in previous works [28,29], for successful embedded printing, the storage moduli of inks should be 1 or 2 orders of magnitude higher than those of the matrix materials (Fig. 1C). For this study, we selected carbomer gel as the matrix material, whose rheological properties have been studied in our previous work [27]. The blooming of the cured flower agrees with the designed objective, showing that the printed hard patterns present good reinforced performances (Fig. 1D and Movie S2). We next demonstrate an omnidirectional bending actuator featuring a soft cylindrical inflating body with 3 independent inner channels (Fig. 1F, left). Subsequently, a stiff reinforced woven at the cross angle of ±20° with respect to the axial orientation of the cylinder was printed to limit its radial inflation. The pressures of 3 channels were controlled by 3 independent air supplies. Figure 1F demonstrates its ability of omnidirectional bending motions.
Rheological and mechanical properties of the ink and matrix
Based on the Voigt model [30], the equivalent elastic modulus Eeq can be predicted by Eq. 1, where Eh and Es are the elastic moduli of the hard and soft inks, respectively, while Vh is the volume fraction of hard material. To obtain the desired pneumatic responses, Eh should be large enough relative to Es to ensure that Eeq is far larger than Es at a given Vh. The soft and hard inks employed here possess elastic moduli of ~0.15 and ~8 MPa, respectively (Fig. 1E). The hard material is composed of Sylgard 184 and SE1700 with short-cut carbon fibers that function as fillers to improve its elastic modulus (Fig. S2). The Sylgard 184+CFs ink viscosity remains within the same order magnitude (from ~2 to ~5 Pa·s) when the concentration of CFs increases from 5 to 20 wt% (Fig. S3), with their loss moduli (G′′) always higher than their storage moduli (G′) (Fig. S4). The addition of SE1700 (or fumed silica) provides hard inks with shear-thinning properties (Fig. S3). The mixture of SE1700 and Sylgard 184 with a weight ratio of 3:1 is selected as the silicone base of the hard ink [27]. The addition of CF fillers hardly changes its viscosity (Fig. S3) and shear moduli (Fig. 2A, top) but greatly influences its mechanical properties. Importantly, we notice a tradeoff between elastic moduli and ultimate strains of CF reinforced polymer composites, i.e., when the concentration of CFs increases from 5 to 20 wt%, the elastic modulus increases from ~2.4 to ~8 MPa, while the ultimate elongation decreased from ~170% to ~75% (Fig. 2B). This result is consistent with previous studies of the mechanical properties of fiber reinforced silicone rubber materials [31].
Eeq=Es1−Vh+EhVh
The soft ink should also meet the rheological and mechanical requirements. Several commercially available silicone rubbers (Ecoflex and Dragon skin series) are used to fabricate SPAs [32]. The fully cured Ecoflex 0030 (Eco30) and Dragon Skin 10 (DS10) possess elastic moduli of ~60 and ~300 kPa, respectively. In our work, we mixed Eco30 and DS10 with different ratios to obtain inks with different elastic moduli (Fig. 2C). Meanwhile, the rheological properties of soft inks were modified by THI-VEX (a commercially available thickener). All inks exhibit shear thinning properties (Fig. S5) with G′ are higher than G′′ (Fig. 2A, bottom), which are ideal for DIW.
Comparing to the casting method, our method allows the 2 distinct materials to be cured together in a single matrix, potentially allowing stronger adhesion between the 2 materials. Tensile tests of the 3 types of specimens representing different fabrication methods were conducted: (a) Soft and hard materials are cured simultaneously in a mold (ME3P, our method). (b) The soft material is first cured in the mold, followed by pouring hard materials into the mold to cure next (U-axis printing method [21]). (c) Soft and hard materials are cured separately, and they were glued together by Sil-poxy silicone adhesive (casting method). The specimens 1 have the highest tensile strength and toughness (1.32 MPa, 2.00 MJ/m2) comparing to specimens 2 (0.95 MPa, 1.10 MJ/m2) and specimens 3 (0.25 MPa, 0.14 MJ/m2) (Fig. 2D). Interestingly, specimens 1 failed at the soft part while specimens 2 and specimens 3 failed at the interface (Fig. S6), again confirming that our method provides a stronger adhesion at the hard/soft material interfaces.
Filament morphology and fusion
Upon choosing the materials family, process parameters were studied by printing filaments in the matrix with different pressures and speeds. Upon curing, the filaments were cut and measured using an optical microscope. Most filaments have an oval-shaped cross-section (Fig. S7). We measured the minor (D1) and major (D2) diameters, i.e., the horizontal and vertical diameters of the cross-section. D1 increases with increasing printing pressure and speed (Fig. 3A). We further calculated the eccentricity (e) of the cross-section according to D1 and D2 (Eq. 2). When extrusion pressure increases from 275 to 419 kPa and printing speed increases from 100 to 800 mm/min, the eccentricities change from 0.5 to 0.8 (Fig. 3B). Such instability of eccentricity makes the prediction of filament diameter challenging. However, the cross-sectional area can be predicted using Eq. 3 [33,34] (details in Section S3 in supplementary information (SI) and Fig. S8), in which X=2τyLP0R, is the ratio of yield and wall shear stress. R (0.33 mm) and L (38.1 mm) are the radii and lengths of the nozzles; Ks (71.8 Pa·s), n (0.712), and τy (163 kPa) are the constancy factor, flow index, and yield stress of the ink fitted by the Herschel–Bulkley model, respectively (Fig. S9). V is the printing speed. Improving printing pressure and decreasing printing speed increases the cross-sectional area (Fig. 3C). The predicted results match well with the experimental results.
e=1−D12D22
S=πR3VP02KsL1nnn+11−Xn+1n−2n2n+11−X2n+1n+2n22n+13n+11−X3n+1n
The fusion of adjacent filaments guarantees the airtightness of the printed chambers. The degree of filament fusion is determined by the step distance when printing pressure and speed are fixed (344.75 kPa, 400 mm/min). D1 (422 μm) and D2 (561 μm) can be found according to the previous results. We first printed horizontal sheets with different step distances (d1) to study the filament fusion in the X and Y directions. The sheet thickness (t1) decreases as the step distance increases from 200 to 300 μm (Fig. 3D). t1 can be predicted based on the volume constant (details in Section S4 in SI). The experimental results match well with the predicted values when d1 is smaller than 300 μm. Otherwise, the fusion fails, leaving gaps between the printed filaments (Fig. S10A). The thickness of the fusion-failed sheet is close to the filaments’ major diameters. Next, we printed a vertical hollow tube to study the fusion in the Z direction. Again, tube thickness (t2) and step distance (d2) are inversely proportional when d2 is smaller than 300 μm. Otherwise, the fusion failed (Fig. 3E and Fig. S10B). Comparing to the previous report [35], our theory improves the prediction accuracy by considering the oval-shaped cross-section of the embedded printed filaments rather than the circular shape (Fig. 3D and E). We define a dimensionless λ=D−dD as the overlap of the 2 adjacent filaments. Successful fusion in the X and Y directions requires λXY > 0.3, while the successful fusion in the Z direction requires the overlap λZ > 0.45. When printing the vertical tube, the first printed filament in the Z direction will be pushed down by the extruded ink at the nozzle tip [25], resulting in λZ > λXY. The fusion of filaments determines the surface roughness of the printed structure (Fig. S10C). The surface roughness of the printed vertical wall (maximum peak to value height, Rz) increases from ~10 to ~600 μm as the step distance increases from 100 to 400 μm (Fig. 3F). When the step distance is larger than 300 μm, the roughness increases dramatically due to the filament gap of the unsuccessful fusion.
Upon printing the main bodies of CRAs, we next conformally printed reinforced patterns on the surface of the CRAs within the same matrix. We first define a nozzle offset value, which is the distance between the tip of the bent nozzle and the surface of the first printed CRAs (Fig. 3G). To improve the printing accuracy during the multimaterial printing, we first printed a vertical wall in the matrix using the abovementioned process parameters. We next printed filaments on the surface of the printed wall with a bent nozzle (20 G) at a slower speed (100 mm/min). As the offset increases from −500 (negative values indicate insertion of the nozzle into the printed surface) to 300 μm, 4 states of the second printed filament positions are defined (Fig. 3H and I): (a) Offset = −500 μm: the filament is fully embedded in the printed wall; (b) −400 μm ≤ Offset ≤ 100 μm: a part of the filament is embedded into the wall; (c) Offset =200 μm: the filament and wall are interfaced by a straight line; (d) Offset ≥ 300 μm: filament and surface are separate. The depth of the filament decreases from ~840 μm as the nozzle moves away from the surface (Fig. 3H). The insertion depth of the ink is larger than that of the nozzle due to the accumulation of the ink at the nozzle tip in the extrusion direction. The areas of cross-sections of the second printed filaments stabilize at ~0.7 μm2, consistent with predictions from Eq. 3.
Response of printed pneumatic actuators
Based on the optimized parameters, we then printed the basic actuator units. Programmable pneumatic responses are achieved by tuning the orientation angle (α, relative to the longitudinal axis) of the reinforced fibers and geometric parameters of inflating bodies (Fig 4A, top, and Movie S3). When α = 90° and the inflating body is in a tubular shape, the actuator elongates ~75% with a pressure of 24 kPa. Contraction is generated as α is tuned to 0°. The contraction ratio reaches ~6% with a pressure of ~14 kPa. This actuator can also serve as an expander because of its radial expansion, which is ~200% with a pressure of ~14 kPa. Tuning α to the value between 0° and 90° shifts the response from linear to twisting motion. As inflating pressure increases to ~14 kPa, the printed actuator (α = 30°) twists ~160°. Adding a 0° constraining fiber at the right side of the elongator, the actuator bends rightwards. The bender bends ~90° with an inflating pressure of ~40 kPa. The inflating processes of 4 actuators are predicted by the FEA (details in Section S2 in SI and Figs. S11 and S12). The simulation results match well with the experimental ones (Fig. 4A, bottom, and Fig. S13). The geometric sizes of the printed actuators are listed in Table S1. We further printed a bender with different scales (Fig. S14). The smallest bender has a wall thickness of 400 μm and a diameter of 4 mm, which is challenging to be fabricated via the traditional casting method. Other features of the abovementioned actuators including the pressure-bearing ability, stiffness, and force are all measured (Figs. S15 to S17). Taking the twistor as an example, thanks to the thin wall thickness and soft inflating materials, the twisting angle of our actuator is one of the highest compared to those fabricated by traditional casting [7,9,12,36 ,37] and U-axis-based printing methods [10,21] (Table S2).
Tuning the orientation angle of the constraining fiber to 15° results in the helical bending motion of the actuator (Fig. S18A), which is controlled by the constraining fiber direction (Fig. S18B). We demonstrate the bioinspired design of cephalopod tentacles’ dexterous movements by changing the inflating body shape to a cone tube (Fig. S19). The reconfigurable response can be achieved by combining different reinforced patterns in a single actuator. In a more complex bending actuator, bending curvature is controlled by the density of horizontal fibers (Fig. S20A), while bending directions can be controlled by the relative positions of the constraining fibers. (Fig. S20B). Thanks to the freeform 3D printing ability, we further demonstrate 2 designs of the embedded 3D printing of spine-like structures on inflating body or reinforced composites to generate local motions. The spines are connected to short ribs printed directly the restricting rings either below (Fig. 4B) or above (Fig. 4C) the spines. Upon inflation, the change in the relative distance (L) between the fiber rings will make the spines either expand toward outside or close toward inside, showing an increase and decrease of β (the angle between the spine tip and vertical line) from −24° to 27° (Fig. 4B, right) and from 45° to 26° (Fig. 4C, right) with an inflating pressure of 20 kPa, respectively.
In addition, we also print shape morphing actuators to demonstrate the conformal integration of hard materials on the surface of soft inflating body with arbitrary patterns. For demonstration, we print an actuator that will morph from a tubular to a vase-like shape. The hard composite pattern consists of 3 segments from the top to the bottom of the CRA: (a) a woven pattern with a cross angle of ± 45° with the top of the woven constrained by a ring; (b) a periodic lozenge pattern limiting the extensions of the actuator; and (c) a pattern with periodic panes to limit both the extension and the expansion of the actuators (Fig. 4D). The theoretical modeling of the CRA upon its inflation (30 kPa) shows a vase-like shape (Fig. 4E, left) that matches well with the experimental result (Fig. 4E and F).
Inverse design of the serially connected actuator for point positioning task
Next, to demonstrate the rapid prototyping of complex actuators, as a proof of concept, we employed an FEA-data-based inverse-design method to guide the manufacturing of arbitrary-shaped CRAs with elongator, twistor, and bender as the basic structural units. The responses of each actuator (elongation distance d, twisting angle γ, and bending angle θ) are tuned by 2 parameters (Fig. 5A, top). For simplification, we predefined the length of the desired CRA (ltotal, 60 mm) and the length of the bending actuator (lbender, 30 mm), and arranged 3 actuators in order of elongator, twistor, and bender. The inflating pressure was set as 15 kPa, which is the maximum pressure under which the pneumatic responses are predictable (Fig. S21). The inverse design requires 2 steps of mapping (Fig. S22): (a) mapping Cartesian coordinates (X, Y, Z) to the pneumatic response of actuator units (d, γ, θ); (b) mapping pneumatic response (d, γ, θ) to the design variables (L1, R1, L2, A1, A2, R2). The first mapping is achieved by the inverse kinetic model (Eq. 4, details in Section S5 in SI and Fig. S23). To accomplish the second mapping, we established a surrogate model from design variables to pneumatic response. We employed 2 commercial software (Solidworks for the generation of the geometry of actuators and Abaqus for FEA, Fig. S24) using Python scripts to sample the training data (Fig. S25). The training data were then fitted to the surrogate model using Kriging’s method (details in Section S6 in SI). Using the surrogate model, we can predict the pneumatic response of soft actuators according to the design variables (Fig. 5A, bottom). To minimize the usage of hard materials, we set the optimization target as the minimization of the total volume of reinforced patterns. Therefore, the second mapping is an optimization problem that is described by Eq. 5, where V is the total volume of hard ink, and Srgte, Srgtb, and Srgtt are surrogate models for elongator, bender, and twistor, respectively. We set the point positioning task as the move from (0,0,60) to (10, 10, −64) in an XYZ space. The corresponding pneumatic response of the elongator, twistor, and bender are 3.02 mm, 0.785, and 0.86 rad, respectively. Using the multiobjective optimization algorithm [38] (details in Section S7 in SI), we can obtain the final design variable values for L1, R1, L2, A1, A2, and R2 as 16.9 mm, 0.66, 13.1 mm, 0.92 rad, 0.261 rad, and 0.56, respectively. All design variables converged to optimal value after ~40 iterations (Fig. S26).
γ=arctany1x1Lθ−x12+y12+6cosθ−6=Lθcosθd=Δz−lbending−lbendingθ+6sinθ
min:V=16.485L1R1+495.55R2+78.75A21−R1+9.4430−L1/sinA1s.t.:SrgteL1R1=d;SrgtbR2A2=θ;Srgtt30−L1A1=α;
The design values were then used to print serially connected actuators (Fig. 5B, left). The actual parameters agree with the designed ones. When the inflating pressure reaches 15 kPa, the elongator section elongates ~3.28 mm, the twistor section twists ~0.729 rad, and the bender section bends ~0.863 rad (Fig. 5B, right). Experimental responses of the actuator (black and white) agree well with the designed shape by FEA (colorful, Fig. 5C, left top). The tip of the actuator travels through a spatial arc and reaches the final point (10.6, 9.5, −67.1) at a pressure of 15 kPa (Fig. S27). The reaching point matches well with the target one (Fig. 5C).
Printed tube-climbing soft robots
As a final demonstration, we printed a soft crawling robot (Movie S4). The robot consists of 2 expanders (α = 0°) and 1 elongator (α = 90°) (Fig. 6A, left). Periodic inflating and deflating of 3 actuators drives the whole robot to move forward or backward, mimicking the inchworm’s locomotion gait [39]. The inflating pressure is ~30 kPa. The inflating and deflating are defined by ON and OFF states, respectively (Fig. 6A, right). At a cycling frequency of 0.5 Hz, the robot can move across the horizontal, curved, vertical, and underwater tubes at the speed of ~0.02, 0.017, 0.013, and 0.016 bl/s, respectively (Fig. 6B and C and Movies S5 and S6). The speed is also related to the inflating frequency, with an optimized frequency of 2 Hz for a speed of ~ 0.07 bl/s (Fig. 6C, bottom). The speed decreases linearly as the inflating frequency decreases when the inflating frequency is smaller than 2 Hz, which is because actuators fail to expand or extend sufficiently. Despite that the peak speed of our robot (0.07 bl/s) is lower than a recently reported balloon-based structure using vacuum to drive the middle contractor (0.19 bl/s) [40], it is comparable to peak speed of most fluid driven soft crawling robots using the extensor as the middle actuator [41].
We further improved the elongator to a bidirectional bender to provide the crawling robot with turning ability (Fig. 6D, top). A miniature camera is hosted in the middle of the crawling robot for real-time image capturing of the surrounding environment. Inflating either channel of the bidirectional bender can make it bend to the opposite direction while inflating both channels simultaneously extend the actuator axially (Fig. 6D, bottom, and Fig. S28). In our work, we control our robot to move across a forked tube. The real-time images are recorded by the miniature camera (Fig. 5E and Movie S7).
Conclusion
Less
In this work, we have developed a ME3P method for the facile and programmable manufacturing of CRAs and CRA-based soft robots. Two different inks with tunable elastic moduli are designed to function as the soft inflating body and hard reinforced patterns of CRAs. The rheological properties of inks and process parameters are investigated to optimize the print quality and resolution. We first demonstrate the benefit of our ME3P by printing unit actuators with different pneumatic responses (elongation, contraction, bending, and twisting). Meanwhile, an FEA data-driving method is proposed to design more complex actuators. A multisegment soft actuator is designed and fabricated to demonstrate our design and fabrication method. Two soft tube climbing robots are printed as our final demonstrations. Overall, our method provides a versatile and promising platform for the future production of soft robots.
Although our method of 4-axis embedded 3D printing has demonstrated the improved design freedom for CRAs, we envision that the integration of composite fiber inks conformally at the inner surfaces of the air channels or even within the soft materials could further extend the versatility of the printed CRAs. Regarding material choices, although the CFs filler could improve the mechanical properties of hard ink, its elastic modulus (~8 MPa) is still lower than that of the Kevlar fiber utilized in fiber reinforced actuators. Printable hard inks with better reinforced effects are under development for future applications. In our multimaterial printing, the calibration error of distance between 2 extrusion nozzles could bring the deviations. An automation calibration method and advanced Computer-Aid Design/Manufacturing software are demanded to reduce the error [42,43]. Besides, during the second printing process, the extruded inks may push and distort the first printed structures. Further studies could be conducted about the rheological requirements of inks and matrix for our printing process.
Materials and Methods
Less
The materials and methods part is presented in Section S1 in Supplementary Materials.
References
Less
1.
Wang Z, Cui W. For safe and compliant interaction: An outlook of soft underwater manipulators. Proc Inst Mech Eng, Part M J Eng Marit Environ. 2021;235(1):3–14.
2.
Shintake J, Cacucciolo V, Floreano D, Shea H. Soft robotic grippers. Adv Mater. 2018;30(29):Article 1707035.
3.
Rus D, Tolley MT. Design, fabrication and control of soft robots. Nature. 2015;521:467–475.
4.
Li G, Chen X, Zhou F, Liang Y, Xiao Y, Cao X, Zhang Z, Zhang M, Wu B, Yin S, et al.Self-powered soft robot in the Mariana trench. Nature. 2021;591:66–71.
5.
Hines L, Petersen K, Lum GZ, Sitti M. Soft actuators for small-scale robotics. Adv Mater. 2017;29(13):Article 1603483.
6.
Polygerinos P, Wang Z, Overvelde JTB, Galloway KC, Wood RJ, Bertoldi K, Walsh CJ. Modeling of soft fiber-reinforced bending actuators. IEEE Trans. Robot. 2015;31(3):778–789.
7.
Connolly F, Walsh CJ, Bertoldi K. Automatic design of fiber-reinforced soft actuators for trajectory matching. Proc Natl Acad Sci U S A. 2017;114(1):51–56.
8.
Yi J, Chen X, Song C, Wang Z. Fiber-reinforced origamic robotic actuator. Soft Robot. 2018;5(1):81–92.
9.
Connolly F, Polygerinos P, Walsh CJ, Bertoldi K. Mechanical programming of soft actuators by varying fiber angle. Soft Robot. 2015;2(1):26–32.
10.
Byrne O, Coulter F, Glynn M, Jones JFX, Ní Annaidh A, O'Cearbhaill ED, Holland DP. Additive manufacture of composite soft pneumatic actuators. Soft Robot. 2018;5(6):726–736.
11.
Chen S, Wang Y, Li D, Chen F, Zhu X. Enhancing interaction performance of soft pneumatic-networks grippers by skeleton topology optimization. Sci China Technol Sci. 2021;64:2709–2717.
12.
Chen S, Chen F, Cao Z, Wang Y, Miao Y, Gu G, Zhu X. Topology optimization of skeleton-reinforced soft pneumatic actuators for desired motions. IEEE/ASME Trans. Mechatron. 2021;26(4):1745–1753.
13.
Mosadegh B, Polygerinos P, Keplinger C, Wennstedt S, Shepherd RF, Gupta U, Shim J, Bertoldi K, Walsh CJ, Whitesides GM. Pneumatic networks for soft robotics that actuate rapidly. Adv Funct Mater. 2014;24(15):2163–2170.
14.
Kim SY, Baines R, Booth J, Vasios N, Bertoldi K, Kramer-Bottiglio R. Reconfigurable soft body trajectories using unidirectionally stretchable composite laminae. Nat Commun. 2019;10:Article 3464.
15.
Singh G, Krishnan G. Designing fiber-reinforced soft actuators for planar curvilinear shape matching. Soft Robot. 2020;7(1):109–121.
16.
Galloway KC, Becker KP, Phillips B, Kirby J, Licht S, Tchernov D, Wood RJ, Gruber DF. Soft robotic grippers for biological sampling on deep reefs. Soft Robot. 2016;3(1):23–33.
17.
Jin LS, Forte AE, Deng BL, Rafsanjani A, Bertoldi K. Kirigami-inspired inflatables with programmable shapes. Adv Mater. 2020;32(33):Article 2001863.
18.
Kim H, Ahn S-k, Mackie DM, Kwon J, Kim SH, Choi C, Moon YH, Lee HB, Ko SH. Shape morphing smart 3D actuator materials for micro soft robot. Mater Today. 2020;41:243–269.
19.
Zhang H, Kumar AS, Chen F, Fuh JY, Wang MY. Topology optimized multimaterial soft fingers for applications on grippers, rehabilitation, and artificial hands. IEEE/ASME Trans Mechatron. 2019;24(1):120–131.
20.
Pagac M, Hajnys J, Ma QP, Jancar L, Jansa J, Stefek P, Mesicek J. A review of vat photopolymerization technology: Materials, applications, challenges, and future trends of 3D printing. Polymers. 2021;13(4):Article 598.
21.
Schaffner M, Faber JA, Pianegonda L, Rühs PA, Coulter F, Studart AR. 3D printing of robotic soft actuators with programmable bioinspired architectures. Nat Commun. 2018;9:Article 878.
22.
Zhou L-y, Gao Q, Fu J-z, Chen Q-y, Zhu J-p, Sun Y, He Y. Multimaterial 3D printing of highly stretchable silicone elastomers. ACS Appl Mater Interfaces. 2019;11(26):23573–23583.
23.
Bhattacharjee T, Zehnder SM, Rowe KG, Jain S, Nixon RM, Sawyer WG, Angelini TE. Writing in the granular gel medium. Sci Adv. 2015;1(8):Article e1500655.
24.
Muth JT, Vogt DM, Truby RL, Mengüç Y, Kolesky DB, Wood RJ, Lewis JA. Embedded 3D printing of strain sensors within highly stretchable elastomers. Adv Mater. 2014;26(36):6307–6312.
25.
Calais T, Sanandiya ND, Jain S, Kanhere EV, Kumar S, Yeow RC-H, Valdivia y Alvarado P. Freeform liquid 3D printing of soft functional components for soft robotics. ACS Appl Mater Interfaces. 2022;14(1):2301–2315.
26.
Sparrman B, du Pasquier C, Thomsen C, Darbari S, Rustom R, Laucks J, Shea K, Tibbits S. Printed silicone pneumatic actuators for soft robotics. Addit Manuf. 2021;40:Article 101860.
27.
Wang Z, Zhang B, Cui W, Zhou N. Freeform fabrication of pneumatic soft robots via multi-material jointed direct ink writing. Macromol Mater Eng. 2022;307(4):Article 2100813.
28.
Truby RL, Wehner M, Grosskopf AK, Vogt DM, Uzel SGM, Wood RJ, Lewis JA. Soft somatosensitive actuators via embedded 3D printing. Adv Mater. 2018;30:1706383.
29.
Zhao J, He N. A mini-review of embedded 3D printing: Supporting media and strategies. J Mater Chem B. 2020;8:10474–10486.
30.
Walpole L. On the overall elastic moduli of composite materials. J Mech Phys Solids. 1969;17(4):235–251.
31.
Lu Y, Wang J, Wang L, Zhao D, Song S. Construction of 3D carbon fiber/carbon nanotube/silicone rubber nanocomposites for stretchable conductors through interface host-guest dendrimers. Compos Sci Technol. 2021;205:Article 108692.
32.
Wallin T, Pikul J, Shepherd R. 3D printing of soft robotic systems. Nat Rev Mater. 2018;3:84–100.
33.
Kelessidis VC, Maglione R, Tsamantaki C, Aspirtakis Y. Optimal determination of rheological parameters for Herschel-Bulkley drilling fluids and impact on pressure drop, velocity profiles and penetration rates during drilling. J Pet Sci Eng. 2006;53:203–224.
34.
Jiang T, Munguia-Lopez JG, Flores-Torres S, Kort-Mascort J, Kinsella JM. Extrusion bioprinting of soft materials: An emerging technique for biological model fabrication. Appl Phys Rev. 2019;6:Article 011310.
35.
Jin Y, Song K, Gellermann N, Huang Y. Printing of hydrophobic materials in fumed silica nanoparticle suspension. ACS Appl Mater Interfaces. 2019;11:29207–29217.
36.
Sedal A, Bruder D, Bishop-Moser J, Vasudevan R, Kota S. A continuum model for fiber-reinforced soft robot actuators. J Mech Robot. 2018;10(2):Article 024501.
37.
Yan JH, Zhang XB, Xu BB, Zhao J. A new spiral-type inflatable pure torsional soft actuator. Soft Robot. 2018;5(5):527–540.
38.
Chen H, Li W, Cui W. Disruption-based multiobjective equilibrium optimization algorithm. Comput Intell Neurosci. 2020;2020.
39.
Zhang B, Fan Y, Yang P, Cao T, Liao H. Worm-like soft robot for complicated tubular environments. Soft Robot. 2019;6:399–413.
40.
Li YT, Peine J, Mencattelli M, Wang J, Ha J, Dupont PE. A soft robotic balloon endoscope for airway procedures. Soft Robot. 2022;9:1014–1029.
41.
Tang C, Du B, Jiang S, Shao Q, Dong X, Liu XJ, Zhao H. A pipeline inspection robot for navigating tubular environments in the sub-centimeter scale. Sci Rob. 2022;7(66):Article eabm8597.
42.
AlZaid S, Hammad N, Albalawi HI, Khan ZN, Othman E, Hauser CAE. Advanced software development of 2D and 3D model visualization for TwinPrint, a dual-arm 3D bioprinting system for multi-material printing. Mat Sci Add Manuf. 2022;1(2).
43.
Lee JM, Sing SL, Yeong WY. Bioprinting of multimaterials with computer-aided design/computer-aided manufacturing. 2020;6(1):245.
Appendix
Less
Year 2023 volume 6 Issue 4
PDF
75
41
Cite this Article
BibTeX
Article Info
doi: 10.34133/research.0122
  • Receive Date：2022-10-31
  • Online Date：2026-10-28
  • Published：2023-04-20
Article Data
Affiliations
History
  • Received：2022-10-31
  • Accepted：2023-03-28
Affiliations
    1Key Laboratory of Coastal Environment and Resources of Zhejiang Province, School of Engineering, Westlake University, Hangzhou, Zhejiang Province, China.
    2Institute of Advanced Technology, Westlake Institute for Advanced Study, Hangzhou, Zhejiang Province, China.
    3Research Center for Industries of the Future, and Key Laboratory of 3D Micro/Nano Fabrication and Characterization of Zhejiang Province, School of Engineering, Westlake University, Hangzhou, Zhejiang Province, China.

Corresponding:

* Address correspondence to: (N.Z.)
(W.C.)
References
Share
https://castjournals.cast.org.cn/joweb/research/EN/10.34133/research.0122
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family		 属数
Number of
genus		 种数
Number of
species		 占总种数比例
Percentage of
total species (%)		 属
Genus		 种数
Number of
species		 占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT
Links
Articles
Latest Articles
Most Read
Collections
Updates
Events
News
Multimedia
About
About Us
Contact
No. 86 Xueyuan South Road, Haidian District, Beijing
100081
010-62662699(Operation and Technical Support)
qkjq@cast.org.cn

Copyright © 2025 China Association for Science and Technology. All rights reserved. For all open access content, the relevant licensing terms apply.
Sponsored by the Office of the Leading Group for Cybersecurity and Informatization of CAST, and supported by Science and Technology Review Publishing House