Home Journals Articles Updates About
CN
image
收藏切换
Fast Bulky Anion Conduction Enabled by Free Shuttling Phosphonium Cations
收藏切换
PDF
Xiaolin Ge1, Yubin He1, Kaiyu Zhang1, Xian Liang1, 2, Chengpeng Wei1, Muhammad A. Shehzad1, Wanjie Song1, Zijuan Ge1, Geng Li1, Weisheng Yu1, Liang Wu1, Tongwen Xu1
Research. Vol 2021 Article ID 9762709
Less
收藏切换
Research. Vol 2021 Article ID 9762709
• Research Article •
Fast Bulky Anion Conduction Enabled by Free Shuttling Phosphonium Cations
Full
Xiaolin Ge1, Yubin He1, Kaiyu Zhang1, Xian Liang1, 2, Chengpeng Wei1, Muhammad A. Shehzad1, Wanjie Song1, Zijuan Ge1, Geng Li1, Weisheng Yu1, Liang Wu1, Tongwen Xu1
Affiliations
  • 1CAS Key Laboratory of Soft Matter Chemistry, Collaborative Innovation Center of Chemistry for Energy Materials, School of Chemistry and Materials Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
  • 2School of Chemistry and Material Engineering, Huainan Normal University, Huainan, Anhui 232001, China
About Author:

Authors’ Contributions

L.W. and T.W.X. conceived the project. L.W., T.W.X., and X.L.G. designed the experiments. X.L.G. and Y.B.H. prepared the polyrotaxane. K.Y.Z. and L.X. helped with the molecular dynamics simulations. C.P.W. and M.A.S. helped with the NMR testing. Z.J.G. and S.W.J. helped with the DSC testing. G.L. and W.S.Y. helped with the membrane preparation. X.L.G. and Y.B.H. wrote the original draft. L.W. and T.W.X. further wrote and revised the manuscript. All authors contributed to the data analysis. Xiaolin Ge and Yubin He contributed equally to this work.

Published: 2021-08-20 doi: 10.34133/2021/9762709
Outline
收藏切换

Highly conductive anion-exchange membranes (AEMs) are desirable for applications in various energy storage and conversion technologies. However, conventional AEMs with bulky HCO3- or Br- as counterion generally exhibit low conductivity because the covalent bonding restrains the tethered cationic group’s mobility and rotation. Here, we report an alternative polyrotaxane AEM with nontethered and free-shuttling phosphonium cation. As proved by temperature-dependent NMR, solid-state NMR, and molecular dynamics simulation, the phosphonium cation possesses a thermally trigged shuttling behavior, broader extension range, and greater mobility, thus accelerating the diffusion conduction of bulky anions. Owing to this striking feature, high HCO3- conductivity of 105 mS cm-1 at 90°C was obtained at a relatively lower ion-exchange capacity of 1.17 mmol g-1. This study provides a new concept for developing highly conductive anion-exchange membranes and will catalyze the exploration of new applications for polyrotaxanes in ion conduction processes.

Xiaolin Ge, Yubin He, Kaiyu Zhang, Xian Liang, Chengpeng Wei, Muhammad A. Shehzad, Wanjie Song, Zijuan Ge, Geng Li, Weisheng Yu, Liang Wu, Tongwen Xu. Fast Bulky Anion Conduction Enabled by Free Shuttling Phosphonium Cations[J]. Research, 2021 , 2021 (8) : 9762709 - . DOI: 10.34133/2021/9762709
Full Text
Less
1. Introduction
Less
Highly conductive anion exchange membranes (AEMs) are still the bottleneck of various energy generation/conversion technologies where fast anion transfer is required. Typically, AEMs are composed of a mechanically robust polymer backbone, tethered cationic groups, and free mobile counter anions like OH-, Br-, and HCO3-. Previously, high OH- ion conductivity has been primarily achieved due to its faster transport kinetics with a combination of Grotthuss mechanism and diffusion mechanism [1, 2]. However, the conduction mechanism of more bulky anions like HCO3- and Br- was much less studied, and low bulky anion conductivity of AEM leads to challenges in its electrochemical applications. For example, in a fuel cell, switching the oxidant from CO2 free air to ambient air would lead to 50% performance loss due to the conversion of OH- to HCO3- [3–5]. In flow batteries where SO42- or Cl- is employed as the charge carrier, AEMs usually exhibit high area resistance, resulting in lower operational current density than proton exchange membranes [6, 7].
The OH- ions are considered to conduct via the Grotthuss mechanism [8–11]. As shown in Figure S17, the hydroxide ions are naturally hydrated by the hydrogen bonding with water molecules to form different hydration complexes (inactive OH−(H2O)4, active OH−(H2O)3). The continuous interconversion between hydration complexes driven by fluctuations in the solvation shell of the hydrated ions results in facile OH− transport. On the other hand, the bulky anions like Br- and HCO3- can hardly form such a hydrogen bonding network with water, thus could not be conducted via the Grotthuss mechanism. Besides, bulky anions are also less mobile, less hydrated, and less dissociated from the ion-conducting groups [12]. These intrinsic disadvantages of bulky anions have (i.e., structural diffusion) [13] led to much lower ion mobility than the OH- ion (relative to OH- in infinite dilution H2O solution: MobilityHCO3−=0.23, MobilityCl−=0.40) [14]. Offsettingthe low ion mobility by increasing the ion concentration often leads to excessive water swelling [15, 16]. A more realistic strategy is creating a graft architecture in which ionic graft chains are covalently bonded to the hydrophobic polymer main chains (Figure 1(a)). This architecture can form water-filled conductive channels via the self-assembly of the hydrophilic side chains [17]. Although creating such an interconnected ion conduction pathway could reduce the tortuosity during ion conduction [14], this strategy cannot resolve bulky anions’ intrinsic low mobility. Consequently, the deliverable bulky anion (Br-, HCO3-, etc.) conductivities are generally <60 mS cm-1 at 80°C, which cannot meet the requirement of practical applications, e.g., >100 mS cm-1 for fuel cell application [14].
Pioneer molecular dynamics research revealed that solvated anions diffuse along the tethered cationic groups on the polymer backbone [18]. The transport across two cationic groups is the rate-determining step and relies on cationic groups’ rotation and motion [19]. The tethered cationic group also influences the anion transport via cation-anion Coulombic interactions and cation-water dipole interaction [20]. Fast cation motion would enhance the anion mobility by contributing to the fluctuation and rearrangement of the solvation shell of the hydrated anion [21, 22]. Since both the mobility and the number of charge carriers determine conductivity [23], the dissociation ability of anions from tethered cationic groups should also be considered. Bulk anions have much lower solvation enthalpy than hydroxyl ion [24]. Tethering the cations close to each other will also decrease the entropy gain in the dissociation process [12]. Consequently, ~60% of the anions exist in the form of ion pair which are unavailable to participate in the conduction process [22]. These pioneer results suggest that the cationic group’s basicity or size should be improved to facilitate anion dissociation ability and hinder ion pair formation [25]. Furthermore, the cationic group’s higher mobility can contribute to enhance anion transport via enhancing the solvation shell fluctuation [21, 22] and reducing the energy barrier when transferring between two cationic groups [19].
Graft polyrotaxanes are mechanically interlocked macromolecular architectures which contains free shuttling guests encircled by macrocyclic hosts (e.g., crown ethers) [26] and provides a new direction for enhancing ion conduction kinetics. In our previous studies, we have demonstrated that the translational shuttling of ion conducting group in a polyrotaxane membrane can promote the Grotthuss conduction of H+ and OH- by facilitating the break and regeneration of hydrogen-bonded network [27, 28], enabling high H+ conductivity of 260.2 mS cm-1 or OH- conductivity of 122 mS cm-1. This study finds that the stimuli trigger motion and rotation in a molecular machine can also promote the diffusion conduction mechanism to deliver high bulky anion conductivity. Furthermore, the shuttling behavior was experimentally demonstrated by temperature-dependent NMR and SSNMR characterization, and the interrelationship between shuttling behavior and ion conductivity was interpreted by DSC and molecular dynamic simulation.
2. Results and Discussion
Less
As shown in Figure 1(b), we have assembled a polyrotaxane AEM which contains a noncovalently tethered and free shuttling cationic group. In this mechanically interlocked macromolecular architecture, a linear molecular guest was firstly mechanically confined within a crown ether macrocyclic host, then end capped with two steric hindrance phosphonium cations. NOESY 2D NMR well elucidated the host-guest intermolecular interaction. Unlike tethered quaternary ammonium group in conventional AEMs, the noncovalently tethered phosphonium cations have exceptionally higher mobility and broader motion range as evidenced by molecular dynamics simulation. Solid-state and temperature-dependent NMR also revealed more obvious free shuttling behavior in response to increasing temperature. Although the favorable advantages originated from the polyrotaxane architecture, the phosphonium cation possesses a high pKb value [29] to improve anion dissociation and larger bulky size to prevent the ions from the formation of condensed ion pairs. Consequently, the as-designed AEM showed high Br- conductivity of 112.1 mS cm-1 and HCO3- conductivity of 105 mS cm-1 at 90°C.
As an upgrade to the traditional AEM with covalently tethered cationic groups, the polyrotaxanes AEM with free shuttling phosphonium cations was constructed by threading a linear guest into the cave of a poly(crown ether) (Figure 1(b)). The linear guest has two benzyl bromide end groups, which were then end-capped with two bulky triphenylphosphine moieties. As depicted in Scheme S1, the poly(crown ether) host 1, which was synthesized via polyacylation, possesses abundant electro-dominating oxygen groups, can selectively recognize the electron-deficient sec-ammonium groups by forming multiple hydrogen bonding [30]. Therefore, a sec-ammonium containing linear guest 2 was synthesized by multistep reactions (Scheme S2-4). Firstly, the condensation reaction between amine and aldehyde group yielded a Schiff base (-C=N-C-) precursor. Treatment with lithium aluminum hydride (LiAlH4) can simultaneously reduce the Schiff base to secondary amine and the terminal ester group to hydroxyl groups. Lastly, the terminal hydroxyl and sec-amine groups were converted into bromomethyl and sec-ammonium groups via a sequential reaction with hydrobromic acid and ammonium hexafluorophosphate (NH4PF6). The obtained linear guest 2 was then threaded into poly(crown ether) host 1 by string in nonpolar solvent for 24 hours. The axle termini were end-capped with two bulky triphenylphosphines to introduce free shutting phosphonium cations as ion conducting groups 4. The bulky nature of phosphonium cations can constrain the liner guest within the caves of crown ether to prevent diffusional loss of the side chains [31].
The successful assemble of hydrogen bond polyrotaxane 4 was firstly confirmed by 1H NMR spectra. As depicted in Figure 2(a), after threading the linear guest 2 into poly crown ether host 1, the NMR signal of sec-ammonium proton down-shifted from δ=9.15 ppm to 9.25 ppm, and the methylene b proton down-shifted from δ=4.19 ppm to 5.22 ppm because of the electro-donating effect of multiple oxygen groups in crown ether. Besides, the nuclear Overhauser effect spectroscopy (NOESY) was conducted to further reveal the correlation between the macrohost and the linear host (Figure 2(b)). The correlation signal in region 1 is originated from the intermolecular electron-transfer between -CH2- moieties in crown ether and the sec-ammonium moiety. The signal in region 2 reflects the interaction between -CH2- and phenyl rings in the linear guest. This result indicated that the linear side chain as well as terminal phosphonium cations was encircled by the macrocyclic hosts, i.e., crown ether, owing to the strong hydrogen-bonding interactions between the components.
The host-guest interaction is realized by the hydrogen bonding between crown ether and –NH2+-group. NaOH treatment could convert the –NH2+- group into –NH- group, thus eliminating the hydrogen-bonding interactions to free the linear host and yield free shuttling polyrotaxane 5. As shown in its 1H NMR spectrum (Figure S8), after converting the sec-ammonium to sec-amine, the proton signal at δ=9.25 disappeared, and a new proton signal at δ=5.31 ppm appeared. Meanwhile, compared with the NOSEY NMR spectrum of hydrogen-bonded polyrotaxane 4 (Figure 2(b)), the NOESY NMR of free shuttling polyrotaxane 5 (Figure 2(c)) did not show any signal for -NH2+- and -O-CH2-CH2-O- intermolecular interaction in region 1. This result confirmed no covalent bonding or noncovalent bonding between the linear guest and poly (crown ether) host in free shuttling polyrotaxane 5. The resulting high mobility and extended motion range of phosphonium cation are expected to effectively promote the diffusion conduction of anions. To rule out the possibility of intramolecular H-H coupling, a COSY experiments had been conducted. As shown in Figure S13, in either the 2D COSY NMR of compound polyrotaxane 4 (Figure S13a) or compound polyrotaxane 5 (Figure S13b), we cannot observe the correlation signals other than their own coupling peaks. So, it could be confirmed that correlation signal in NOESY spectrum represents the coupling between the crown ether and the linear axis.
The thermal-responsiveness of shuttling behavior could be reflected by the evolution of relative position between the crown ether host and the liner guest. At low temperatures, the linear guest has lower mobility and smaller shuttling range due to the hydrogen bonding. As a result, the sec-amine was mainly located in the caves of crown ether. With increasing temperature, the linear guest can easily overcome the energy barrier, enabling accelerated shuttling behavior. Other moieties in the linear guest (phenyl rings, benzyl methyl groups, etc.) can thus have a higher possibility to move into the caves of crown ether. As a verification of this assumption, temperature-dependent liquid-state 1H NMR analysis of hydrogen-bonded polyrotaxane 4 was conducted and depicted in Figure 3(a) and Figure S6. When temperature increases from 25 to 70°C, the NMR signal (a′) of -NH2+- shifted downfield from 9.2 to 9.3 ppm as a result of less shielding effect from the crown ether. Meanwhile, the NMR signals (b′) of methylene group shifted upfield from 5.21 to 5.15 ppm due to the higher possibility to coexist with crown ether in the same plane, suggesting that the linear guest can easily slip back and forth through the caves of the macrocyclic host. Besides, temperature-dependent liquid-state 31P NMR was also conducted. With increasing temperature from 25°C to 55°C, the phosphorus signal shifted upfield from 23.17 to 23.09 ppm, which is consistent with 1H NMR results (Figure S7).
In the above results, the shifting of proton signals from the linear guest was observed. However, the crown ether signals overlapped with -(CH2-CH2)4- signals in the backbone; thus, their shifting trend with increasing temperature could not be clearly observed. Therefore, a rotaxane 6 was synthesized as a model compound (Scheme S8) [24] and characterized by temperature-dependent 1H NMR (Figure 3(b) and Figure S10). The linear guest signals a″, b″, and c″ showed the same shifting trend as that of poly rotaxane results. These results confirmed that the polyrotaxane possesses temperature-responsive shuttling behavior in the liquid state, i.e., low energy barrier at high temperature leads to fast shuttling and extended motion range.
The next target is to prove the thermal-responsiveness of shuttling behavior in all solid-state since low humidity environment may occur in some applications like fuel cell [32]. Due to the low resolution of solid-state 1H NMR, the abovementioned rotaxane 6 was employed as the model compound. Its temperature-dependent solid-state 1H NMR was depicted in Figure 3(c) and Figure S11. With increasing temperature, the signals of aromatic protons (5.8-7.4 ppm) and aliphatic protons (2.6-3.6 ppm and 0.3-1.8 ppm) both showed changes in chemical shift and signal shape. However, due to the interference between multiple proton signals, peaks tend to widen and overlap with each other. Temperature-dependent 31P NMR of the above rotaxane 6 was further conducted to eliminate this effect (Figure 3(d) and Figure S12). The signal at 26.5 ppm was assigned to the phosphorus in the cationic group. With increasing temperature from 25°C to 65°C, apparent upfield shifting from 26.5 to 26.0 ppm was observed, suggesting an increasing shielding effect from the oxygen in the crown ether. These results confirmed that even in the solid-state, the rotaxane possesses temperature-responsive shuttling behavior.
The above results suggest that there is a transition temperature for the polyrotaxane entity, above which the motion of linear guest will be significantly accelerated. To determine this transition temperature, differential scanning calorimetry (DSC) curve of the rotaxane 6 was recorded (Figure 4(a)). The curve showed a single endothermic peak over the range of 65-80°C, suggesting the activation temperature for overcoming the energy barrier and enabling the free shuttling behavior of linear guest. As for the hydrogen-bonded polyrotaxane 4, a higher transition temperature (70-80°C) was observed (Figure 4(b)) due to the extra steric hindrance effect from the high molecular weight and entanglement of polymer backbones. In Figure 4(c), the free shuttling polyrotaxane showed no endothermic peak due to the elimination of hydrogen bonding between crown ether host and linear guest, suggesting that the cationic group’s high mobility could be achieved at a much lower temperature. Besides, no endothermic peak was detected for the poly(crown ether) host in the temperature range of 0 to 100°C (Figure 4(d)); thus, the possible interference from glass transition or melting of polymer backbones could be excluded.
Molecular dynamics simulation (Forcite module) of the polyrotaxane system was further conducted to intuitively elucidate the mobility and motion range of free shuttling cationic groups. The molecular structures were built and optimized under PCFF force field, and the angle-distance probability density distribution was plotted. As shown in Figure 4(e) and Figure S14, the distance from the cationic group to the crown ether plane is defined as vector d (y-axis), and the angle between linear guest and crown ether plane is defined as vector θ (x-axis). In order to simulate conventional tethered AEM, a constant restraint of 10 kcal/mol/Å2 was applied between crown ether and the -NH2+- group to simulate the covalent bonding (Figure S14b). The color from blue to red reflects the increased probability density distribution of a particular relative positive between cationic groups and the crown ether plane. At low temperatures, both the conventional tethered AEM structure and the as-designed polyrotaxane structure showed θ in the range of 50-130o, suggesting similar oscillation behavior of the cationic groups. However, the polyrotaxane structure showed a d value of 5.5-9 Å, which is in sharp contrast to the conventional tethered structure (d=7-8 Å). This suggests the linear guest can shuttle back and forth through caves of crown ether. The oscillation and shuttling behavior of phosphonium cations originating from its nontethered nature would ensure improved mobility and extended motion range to promote bulky anions’ conduction.
With increasing temperatures, the motion behavior of conventional AEM shows no noticeable change, with a narrow range of relative positions as well as a highly concentrated possibility density in the center. These results suggest that the ion-conducting groups are mainly fixed at one particular position due to the confinement of the covalent bond. In sharp contrast, the polyrotaxane AEM shows both increased scope of relative position and more even distribution of possibility density due to the unique shuttling characteristic of poly-rotaxane. In addition, evident temperature responsiveness was observed. Above 50°C, the motion range of phosphonium cations increased obviously. This free shuttling behavior with an extensive motion range is believed to refine bulk anions’ conduction mechanism, by providing extra solvation shell fluctuation [21] and reducing the energy barrier when transferring between two cationic groups [19].
AEMs were prepared from the free shuttling polyrotaxane 5 via solution casting method. Its properties including ion exchange capacity, water uptake, swelling ratio, and Br-/HCO3-/OH- conductivity are summarized in Table S1, Table S2, and Figure S15. The mechanical strength and thermal stability were also measured (Figure S16). Results showed that mechanical properties (tensile strength and elongation at break) of the hydrated membrane are improved with the increasing temperature (Figure S16a), and the AEM possesses good thermal stability up to 150°C with sufficient for practical application (Figure S16b). Firstly, the favorable advantages from the free shuttling phosphonium cations were demonstrated by comparing the conductivity of the polyrotaxane-based AEM and conventional tethered AEMs (Figures 5(a) and 5(b)) [15–17, 33–44]. For conventional AEMs, the HCO3- and Br-conductivities showed an increasing linear trend with temperature. Meanwhile, the conductivity-temperature plot of polyrotaxane AEMs shows a distinct two-segment characteristic. From 30°C to 60°C, the conductivity increased slowly with temperature, from 20.1 to 40.1 mS cm-1 for HCO3- and 22.9 to 46.7 mS cm-1 for Br-. Above the transition temperature (65°C), the accelerated shuttling of phosphonium cations yielded a dramatic leap in conductivity, i.e., 105 mS cm-1 for HCO3- and 112.1 mS cm-1 for Br- at 90°C, by enabling higher anion mobility and better anion dissociation. Note that this good conductivity was achieved at a low ion exchange capacity of 1.17 mmol/g for HCO3- and 1.08 mmol/g for Br- (IEC is defined as mmol of ion-conducting groups in per gram of dried membranes, Table S1).
Apart from the dramatically improved conductivity, the hydrated AEM also shows a thermal triggered appearance transition. As shown in Figure 5(c), the dry transparent membrane in the dehydration state became opaque after soaked in water at 70°C for 2 hours, suggesting the dissolution of the linear guest in water. Thus, the remaining hydrophobic polymer backbone became incompatible with the aqueous linear guest, and macroscopic phase separation occurred. Interestingly, this transition behavior is reversible when the membrane became transparent again after it was dried. This interesting thermal triggered appearance transition further proved the temperature responsiveness and reversibility of shuttling behavior. To exclude the water effect, the dry membrane was heated at 70°C for 2 hours, and the result is shown in Figure S18a. The results show that there is no obvious appearance change of membrane. We also tested the SEM of the dry membrane, as shown in Figure S18b and Figure S18c. It is noteworthy that the dry membrane displayed quite a compact structure with no defect, which is coherent to its transparent and dense appearance as shown in Figure S18a.
The above assumption was confirmed by 1H NMR analysis. Figure 5(d) shows the 1H NMR spectra of the membrane/D2O mixture. When the temperature increased from 25°C to 60°C, the grafted chain’s proton signals appeared. Moreover, all the proton signals disappeared when the membrane was removed from the D2O. It indicates that the dissolution of the mobile guest chains in the water channel is temperature-dependent and that diffusion loss from the poly(crown ether) host does not occur. Therefore, the polyrotaxane structure resembled a polymer blend with hydrophilic cationic groups that can probably dissolve in the water channel and possess high mobility to accelerate bulky anion’s conduction.
3. Discussion
Less
In conclusion, a polyrotaxane system featured with free shuttling phosphonium cations as ion-conducting group was assembled to address bulky anions’ low conductivity. The temperature responsiveness and reversibility of shuttling behavior were proved by temperature-dependent solid-state NMR and molecular dynamics simulation. This exceptional free-shuttling anion carrier allows promoted anion dissociation, hydration, and mobility, thus yielding an excellent anion conductivity of 105 mS cm-1 for HCO3- and 112.1 mS cm-1 for Br- at a low ion exchange capacity. Broad applications of this unique polyrotaxane system in ion separation processes are currently in progress.
4. Materials and Methods
Less
4.1. Materials
Hydrobromic acid, triphenylphosphine, and magnesium sulfate were purchased from Sinopharm Chemical Reagent Co., Ltd. Eaton’s reagent, diphenyl ether (99%), sebacic acid (98%), methyl-4-formylbenzoate (99%), ammonium hexafluorophosphate (98%), and lithium aluminum hydride (LiAlH4) (97%) methyl-4-(aminomethyl) benzoate hydrochloride were purchased from Shanghai Energy-Chemical Co. Ltd. Dibenzo-24-crown-8 was purchased from Tokyo Chemical Industry (TCI). All reagents were used as received.
4.2. Preparation of Poly(Crown Ether) 1
Dibenzo-24-crown-8 (1 mmol), sebacic acid (4 mmol), and diphenyl ether (3 mmol) were dissolved in Eaton’s reagent (12.8 mL), and the mixture was heated to 40°C and stirred for 24 h. After the reaction was stirred for 24 h, it was poured into water. The slightly yellow fibers that formed were filtered off and washed with water. After the fibers were dried, compound 1d was obtained as a white fiber-like polymer, 2a (98%).
4.3. Preparation of Compound 2c
Compound 2a (1 mmol) and compound 2a (1 mmol) were dissolved in dry toluene (60 mL), and the mixture was heated under reflux in an argon atmosphere for 24 h using a Dean-Stark apparatus. After the reaction mixture cooled, the solvents were removed under vacuum, and the remaining components were washed with ethanol (3×30 mL). Compound 2c was isolated as a white solid (85%).
4.4. Preparation of Compound 2d
A solution of compound 2c (1 equiv) in dry THF was cooled to 0°C, and powdered LiAlH4 (6 equiv) was added to the solution over a period of 1 h. The mixture was then warmed to room temperature and heated under reflux in an argon atmosphere overnight. After the reaction was stirred overnight, it was cooled to 0°C. Sodium sulfate decahydrate (2 equiv) was then carefully added to the flask. The mixture was stirred for 1 h and filtered and washed with THF. The filtrate was collected and dried (with MgSO4), and the solvent was removed under vacuum to give compound 2d as a yellow liquid (70%).
4.5. Preparation of Compound 2
Compound 2d (1 mmol) was dissolved in 30 mL of HBr (48%), and the resulting mixture was heated to 100°C and stirred for 24 h. Then, it was cooled to room temperature and filtered and washed with water. The white solid was dissolved in a saturated, aqueous NH4PF6 solution and stirred for 24 h. The reaction mixture was again filtered and washed with water to give compound 2 as a white solid (85%).
4.6. Preparation of Polyrotaxane 4
Compound 1 (1 mmol) and compound 2 (1 mmol) were dissolved in CH3CN/CHCl3 (30 mL, 1 : 2); the mixture was stirred at room temperature for 24 h. Then, triphenylphosphine (2.5 mmol) was added to the reaction solution and left to stir at room temperature for 48 h. After the mixture was stirred for 48 h, it was poured into diethyl ether and stirred. The yellow fibers that formed were filtered off, wash with diethyl ether, and dried under flowing air to give compound 4.
4.7. Preparation of Membrane 4·Br-, 5·OH-, 5·HCO3-
Polyrotaxane 4 was dissolved in CH3CN to form a 5 wt% casting solution that was cast onto a tetrafluoroethylene plate. The cast films were heated at 30°C to remove the solvent. After the drying process, flexible, transparent, and yellow-tinged polyrotaxane AEMs 4·Br- (with thickness of 50±5  μm) were obtained. All membranes were fully converted to the HCO3- and OH- form via immersion in aqueous KHCO3 (1 mol·L-1) and KOH (1 mol·L-1) solution at room temperature for 24 h, followed by thorough washing and storage in sealed sample bottles (full of deionized water). This membrane was denoted polyrotaxane AEMs 5·HCO3- and 5·OH-.
4.8. Preparation of Rotaxane 6
Dibenzo-24-crown-8 (1 mmol) and compound 2 (1.5 mmol) were dissolved in CH3CN/CHCl3 (20 mL, 1 : 1); the mixture was stirred at room temperature for 1 h. Then, triphenylphosphine (4 mmol) was added to the solution; the reaction was then left to stir at room temperature for 24 h. The resulting white precipitate was filtered off and washed with CH2Cl2. The organic layer was removed, and the resulting solid redissolved in CH2Cl2 and any insoluble material removed by filtration. Et2O was then added to the CH2Cl2 solution; the resulting white precipitate was filtered and wash with more Et2O to give rotaxane 6.
4.9. Molecular Dynamics (MD) Simulations
Molecular dynamics simulations were performed using Forcite module. Molecular structures were built and optimized under PCFF force field. We performed 400 ps dynamics of AEM under NVT ensemble with different temperature of 303-363 K. The Nosé–Hoover–Langevin thermostat (Qratio of 0.01) was used to control temperature, with 1 fs time step. To elucidate the difference in mobility and motion range of the free shuttling AEM and conventional tethered AEM, the angle-distance probability density distribution was plotted. As shown in Figure S14a, the center mass of rotaxane was defined as point A, the P atom in the phosphonium cations was defined as point P, and O atom in crown ether was defined as point O. The angle (θ) was defined as P-A-O, and the distance (d) was defined as P-A. In order to simulate conventional tethered AEM, a constant restraint of 10 kcal/mol/Å2 was applied between crown ether and the -NH2+- group to simulate the covalent bonding (Figure S14b). In the probability density distribution profile (Figure S14c), red zone indicates high density probability, and green zone indicates low density probability.
Funding
Less
  • National Natural Science Foundation of China(21875233; 22038013; 21706247; 21720102003)
  • National Key R&D Program of China(2020YFB1505601)
References
Less
1
Wyithe J., and Loeb A., “Magnification of light from many distant quasars by gravitational lenses,” Nature, vol. 417, no. 6892, pp. 923–925, 2002
2
Merle G., Wessling M., and Nijmeijer K., “Anion exchange membranes for alkaline fuel cells: a review,” Journal of Membrane Science, vol. 377, no. 1-2, pp. 1–35, 2011
3
Krewer U., Weinzierl C., Ziv N., and Dekel D. R., “Impact of carbonation processes in anion exchange membrane fuel cells,” Electrochimica Acta, vol. 263, pp. 433–446, 2018
4
Vega J., Chartier C., and Mustain W. E., “Effect of hydroxide and carbonate alkaline media on anion exchange membranes,” Journal of Power Sources, vol. 195, no. 21, pp. 7176–7180, 2010
5
Zhang H., Chen D. Z., Xianze Y., and Yin S. B., “Anion-exchange membranes for fuel cells: synthesis strategies, properties and perspectives,” Fuel Cells, vol. 15, no. 6, pp. 761–780, 2015
6
Li X., Zhang H., Mai Z., Zhang H., and Vankelecom I., “Ion exchange membranes for vanadium redox flow battery (VRB) applications,” Energy & Environmental Science, vol. 4, no. 4, article 1147, 2011
7
Wang W., Luo Q., Li B., Wei X., Li L., and Yang Z., “Recent progress in redox flow battery research and development,” Advanced Functional Materials, vol. 23, no. 8, pp. 970–986, 2013
8
Choi P., Jalani N. H., and Datta R., “Thermodynamics and proton transport in Nafion,” Journal of the Electrochemical Society, vol. 152, no. 8, p. A1548, 2005
9
Li N., and Guiver M. D., “Ion transport by nanochannels in ion-containing aromatic copolymers,” Macromolecules, vol. 47, no. 7, pp. 2175–2198, 2014
10
Hickner M. A., “Water-mediated transport in ion-containing polymers,” Journal of Polymer Science Part B: Polymer Physics, vol. 50, no. 1, pp. 9–20, 2012
11
Hibbs M. R., Hickner M. A., Alam T. M., McIntyre S. K., Fujimoto C. H., and Cornelius C. J., “Transport properties of hydroxide and proton conducting membranes,” Chemistry of Materials, vol. 20, no. 7, pp. 2566–2573, 2008
12
Marino M. G., Melchior J. P., Wohlfarth A., and Kreuer K. D., “Hydroxide, halide and water transport in a model anion exchange membrane,” Journal of Membrane Science, vol. 464, pp. 61–71, 2014
13
Agmon N., “The Grotthuss mechanism,” Chemical Physics Letters, vol. 244, no. 5-6, pp. 456–462, 1995
14
Varcoe J., Atanassov P., Dekel D. R., Herring A. M., Hickner M. A., Kohl P. A., Kucernak A. R., Mustain W. E., Nijmeijer K., Scott K., Xu T., and Zhuang L., “Anion-exchange membranes in electrochemical energy systems,” Energy & Environmental Science, vol. 7, no. 10, pp. 3135–3191, 2014
15
Hou J., Liu Y., Ge Q., Yang Z., Wu L., and Xu T., “Recyclable cross-linked anion exchange membrane for alkaline fuel cell application,” Journal of Power Sources, vol. 375, pp. 404–411, 2018
16
Liu L., Li D., Xing Y., and Li N., “Mid-block quaternized polystyrene-b-polybutadiene-b -polystyrene triblock copolymers as anion exchange membranes,” Journal of Membrane Science, vol. 564, pp. 428–435, 2018
17
He Y., Zhang J., Liang X., Shehzad M. A., Ge X., Zhu Y., Hu M., Yang Z., Wu L., and Xu T., “Achieving high anion conductivity by densely grafting of ionic strings,” Journal of Membrane Science, vol. 559, pp. 35–41, 2018
18
Takaba H., Hisabe T., Shimizu T., and Alam M. K., “Molecular modeling of OH− transport in poly(arylene ether sulfone ketone)s containing quaternized ammonio-substituted fluorenyl groups as anion exchange membranes,” Journal of Membrane Science, vol. 522, pp. 237–244, 2017
19
Yang G., Hao J., Cheng J., Zhang N., He G., Zhang F., and Hao C., “Hydroxide ion transfer in anion exchange membrane: a density functional theory study,” International Journal of Hydrogen Energy, vol. 41, no. 16, pp. 6877–6884, 2016
20
Grew K. N., and Chiu W. K. S., “A dusty fluid model for predicting hydroxyl anion conductivity in alkaline anion exchange membranes,” Journal of the Electrochemical Society, vol. 157, no. 3, p. B327, 2010
21
Orekhov M., “Fluctuation enhancement of ion diffusivity in liquids,” Physical Chemistry Chemical Physics, vol. 19, no. 48, pp. 32398–32403, 2017
22
Amel A., Gavish N., Zhu L., Dekel D. R., Hickner M. A., and Ein-Eli Y., “Bicarbonate and chloride anion transport in anion exchange membranes,” Journal of Membrane Science, vol. 514, pp. 125–134, 2016
23
Disabb-Miller M., Johnson Z. D., and Hickner M. A., “Ion motion in anion and proton-conducting triblock copolymers,” Macromolecules, vol. 46, no. 3, pp. 949–956, 2013
24
Marcus Y., “Tetraalkylammonium ions in aqueous and non-aqueous solutions,” Journal of Solution Chemistry, vol. 37, no. 8, pp. 1071–1098, 2008
25
Gu S., Cai R., Luo T., Chen Z., Sun M., Liu Y., He G., and Yan Y., “A soluble and highly conductive ionomer for high-performance hydroxide exchange membrane fuel cells,” Angewandte Chemie (International Ed. in English), vol. 48, no. 35, pp. 6499–6502, 2009
26
Aprahamian I., “Molecules bearing robotic arms,” Nature Chemistry, vol. 8, no. 2, pp. 97–99, 2016
27
Ge X., He Y., Guiver M. D., Wu L., Ran J., Yang Z., and Xu T., “Alkaline anion-exchange membranes containing mobile ion shuttles,” Advanced Materials, vol. 28, no. 18, pp. 3467–3472, 2016
28
Ge X., He Y., Liang X., Wu L., Zhu Y., Yang Z., Hu M., and Xu T., “Thermally triggered polyrotaxane translational motion helps proton transfer,” Nature Communications, vol. 9, no. 1, p. 2297, 2018
29
Henderson W., and Streuli C. A., “The basicity of phosphines,” Journal of the American Chemical Society, vol. 82, no. 22, pp. 5791–5794, 1960
30
ARUNACHALAM M., and GIBSON H. W., “Recent developments in polypseudorotaxanes and polyrotaxanes,” Progress in Polymer Science, vol. 39, no. 6, pp. 1043–1073, 2014
31
Rowan S., Cantrill S. J., and Stoddart J. F., “Triphenylphosphonium-stoppered [2]rotaxanes,” Organic Letters, vol. 1, no. 1, pp. 129–132, 1999
32
Park C., Lee S. Y., Hwang D. S., Shin D. W., Cho D. H., Lee K. H., Kim T. W., Kim T. W., Lee M., Kim D. S., Doherty C. M., Thornton A. W., Hill A. J., Guiver M. D., and Lee Y. M., “Nanocrack-regulated self-humidifying membranes,” Nature, vol. 532, no. 7600, pp. 480–483, 2016
33
Page O., Poynton S. D., Murphy S., Lien Ong A., Hillman D. M., Hancock C. A., Hale M. G., Apperley D. C., and Varcoe J. R., “The alkali stability of radiation-grafted anion-exchange membranes containing pendent 1-benzyl-2,3-dimethylimidazolium head-groups,” RSC Advances, vol. 3, no. 2, pp. 579–587, 2013
34
Lin C., Wu H. Y., Li L., Wang X. Q., Zhang Q. G., Zhu A. M., and Liu Q. L., “Anion conductive triblock copolymer membranes with flexible multication side chain,” ACS Applied Materials & Interfaces, vol. 10, no. 21, pp. 18327–18337, 2018
35
Liu F. H., Lin C. X., Hu E. N., Yang Q., Zhang Q. G., Zhu A. M., and Liu Q. L., “Anion exchange membranes with well-developed conductive channels: effect of the functional groups,” Journal of Membrane Science, vol. 564, pp. 298–307, 2018
36
Deavin O. I., Murphy S., Ong A. L., Poynton S. D., Zeng R., Herman H., and Varcoe J. R., “Anion-exchange membranes for alkaline polymer electrolyte fuel cells: comparison of pendent benzyltrimethylammonium- and benzylmethylimidazolium-head-groups,” Energy & Environmental Science, vol. 5, no. 9, p. 8584, 2012
37
Cheng X., Wang J., Liao Y., Li C., and Wei Z., “Enhanced conductivity of anion-exchange membrane by incorporation of quaternized cellulose nanocrystal,” ACS Applied Materials & Interfaces, vol. 10, no. 28, pp. 23774–23782, 2018
38
Ran J., Ding L., Chu C., Liang X., Pan T., Yu D., and Xu T., “Highly conductive and stabilized side-chain-type anion exchange membranes: ideal alternatives for alkaline fuel cell applications,” Journal of Materials Chemistry A, vol. 6, no. 35, pp. 17101–17110, 2018
39
Yang Z., Guo R., Malpass-Evans R., Carta M., McKeown N. B., Guiver M. D., Wu L., and Xu T., “Highly conductive anion-exchange membranes from microporous Tröger’s base polymers,” Angewandte Chemie International Edition, vol. 55, no. 38, pp. 11499–11502, 2016
40
Liu Y., Zhou J., Hou J., Yang Z., and Xu T., “Hyperbranched polystyrene copolymer makes superior anion exchange membrane,” ACS Applied Polymer Materials, vol. 1, no. 1, pp. 76–82, 2019
41
Zha Y., Disabb-Miller M. L., Johnson Z. D., Hickner M. A., and Tew G. N., “Metal-cation-based anion exchange membranes,” Journal of the American Chemical Society, vol. 134, no. 10, pp. 4493–4496, 2012
42
Wang L., Brink J. J., Liu Y., Herring A. M., Ponce-González J., Whelligan D. K., and Varcoe J. R., “Non-fluorinated pre-irradiation-grafted (peroxidated) LDPE-based anion-exchange membranes with high performance and stability,” Energy & Environmental Science, vol. 10, no. 10, pp. 2154–2167, 2017
43
Hou J., Liu Y., Liu Y., Wu L., Yang Z., and Xu T., “Self-healing anion exchange membrane for pH 7 redox flow batteries,” Chemical Engineering Science, vol. 201, pp. 167–174, 2019
44
Kwasny M., Zhu L., Hickner M. A., and Tew G. N., “Thermodynamics of counterion release is critical for anion exchange membrane conductivity,” Journal of the American Chemical Society, vol. 140, no. 25, pp. 7961–7969, 2018
Appendix
Less
Year 2021 volume 2021 Issue 8
PDF
73
41
Cite this Article
BibTeX
Article Info
doi: 10.34133/2021/9762709
  • Receive Date：2021-05-12
  • Online Date：2026-10-27
  • Published：2021-08-20
Article Data
Affiliations
History
  • Received：2021-05-12
  • Accepted：2021-08-09
Funding
National Natural Science Foundation of China(21875233; 22038013; 21706247; 21720102003)
National Key R&D Program of China(2020YFB1505601)
Affiliations
    1CAS Key Laboratory of Soft Matter Chemistry, Collaborative Innovation Center of Chemistry for Energy Materials, School of Chemistry and Materials Science, University of Science and Technology of China, 96 Jinzhai Road, Hefei, Anhui 230026, China
    2School of Chemistry and Material Engineering, Huainan Normal University, Huainan, Anhui 232001, China
References
Share
https://castjournals.cast.org.cn/joweb/research/EN/10.34133/2021/9762709
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family		 属数
Number of
genus		 种数
Number of
species		 占总种数比例
Percentage of
total species (%)		 属
Genus		 种数
Number of
species		 占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT
Links
Articles
Latest Articles
Most Read
Collections
Updates
Events
News
Multimedia
About
About Us
Contact
No. 86 Xueyuan South Road, Haidian District, Beijing
100081
010-62662699(Operation and Technical Support)
qkjq@cast.org.cn

Copyright © 2025 China Association for Science and Technology. All rights reserved. For all open access content, the relevant licensing terms apply.
Sponsored by the Office of the Leading Group for Cybersecurity and Informatization of CAST, and supported by Science and Technology Review Publishing House