收藏切换
Largely Suppressed Magneto-Thermal Conductivity and Enhanced Magneto-Thermoelectric Properties in PtSn4
收藏切换
PDF
Chenguang Fu1, Satya N. Guin1, Thomas Scaffidi2, 3, Yan Sun1, Rana Saha4, Sarah J. Watzman5, Abhay K. Srivastava4, 6, Guowei Li1, Walter Schnelle1, Stuart S. P. Parkin4, Claudia Felser1, Johannes Gooth1
Research. Vol 2020 Article ID 4643507
Less
收藏切换
Research. Vol 2020 Article ID 4643507
• Research Article •
Largely Suppressed Magneto-Thermal Conductivity and Enhanced Magneto-Thermoelectric Properties in PtSn4
Full
Chenguang Fu1, Satya N. Guin1, Thomas Scaffidi2, 3, Yan Sun1, Rana Saha4, Sarah J. Watzman5, Abhay K. Srivastava4, 6, Guowei Li1, Walter Schnelle1, Stuart S. P. Parkin4, Claudia Felser1, Johannes Gooth1
Affiliations
  • 1Max Planck Institute for Chemical Physics of Solids, 01187 Dresden, Germany
  • 2Department of Physics, University of California, Berkeley, CA 94720, USA
  • 3Department of Physics, University of Toronto, Toronto, Ontario M5S 1A7, Canada
  • 4Max Planck Institute of Microstructure Physics, 06120 Halle, Germany
  • 5Department of Mechanical and Materials Engineering, University of Cincinnati, Cincinnati, OH 45219, USA
  • 6Institute of Physics, Martin Luther University Halle-Wittenberg, 06120 Halle, Germany
Published: 2020-04-20 doi: 10.34133/2020/4643507
Outline
收藏切换

Highly conductive topological semimetals with exotic electronic structures offer fertile ground for the investigation of the electrical and thermal transport behavior of quasiparticles. Here, we find that the layer-structured Dirac semimetal PtSn4 exhibits a largely suppressed thermal conductivity under a magnetic field. At low temperatures, a dramatic decrease in the thermal conductivity of PtSn4 by more than two orders of magnitude is obtained at 9 T. Moreover, PtSn4 shows both strong longitudinal and transverse thermoelectric responses under a magnetic field. Large power factor and Nernst power factor of approximately 80–100  μW·cm-1·K-2 are obtained around 15 K in various magnetic fields. As a result, the thermoelectric figure of merit zT is strongly enhanced by more than 30 times, compared to that without a magnetic field. This work provides a paradigm for the decoupling of the electron and hole transport behavior of highly conductive topological semimetals and is helpful for developing topological semimetals for thermoelectric energy conversion.

Chenguang Fu, Satya N. Guin, Thomas Scaffidi, Yan Sun, Rana Saha, Sarah J. Watzman, Abhay K. Srivastava, Guowei Li, Walter Schnelle, Stuart S. P. Parkin, Claudia Felser, Johannes Gooth. Largely Suppressed Magneto-Thermal Conductivity and Enhanced Magneto-Thermoelectric Properties in PtSn4[J]. Research, 2020 , 2020 (4) : 4643507 - . DOI: 10.34133/2020/4643507
In recent years, thermoelectric effects have attracted considerable attention in the fields of materials science and solid-state physics and chemistry. Practically, solid-state thermoelectric conversion offers a promising solution for energy harvesting and cooling [1]. Furthermore, investigations of thermoelectric phenomena are important for understanding the fundamental transport behavior of quasiparticles in solid materials [2]. The thermoelectric efficiency of a material is gauged by the figure of merit, zT=S2T/ρκ, where S, T, ρ, and κ are the thermopower, absolute temperature, electrical resistivity, and thermal conductivity, respectively. The term S2/ρ is known as the thermoelectric power factor. Although the expression is simple, obtaining a high zT is a challenging task because these transport parameters are interrelated. As a compromise, heavily doped semiconductors with moderate electrical conductivity and thermopower values have become the most widely investigated thermoelectric systems [3–5]. Metals or semimetals, owing to strong coupling of S, ρ, and the electronic thermal conductivity κe, have attracted much less attention for thermoelectric studies. The key to developing metals or semimetals for thermoelectric application lies in the decoupling of the three electrical transport parameters.
In a two-carrier semimetal system, the thermopower S is expressed as Seσe+Shσh/σe+σh, where e and h indicate electrons and holes, respectively, and σ is the electrical conductivity. Se and Sh generally have opposite signs and thus balance each other’s contribution to S. Assuming the conduction and valence bands have symmetric structure and the Fermi level lies between them, the terms Seσe and Shσh will have similar values but opposite signs, so S will be almost zero. Therefore, semimetals with symmetric conduction and valence bands have generally been viewed as poor thermoelectric materials. One way to overcome this disadvantage is to look for semimetals with a large asymmetry between the conduction and valence bands, where the large disparity in their electron and hole effective masses could ensure a sizable S [6, 7]. Another recently proposed method of generating a large thermopower in topological Dirac/Weyl semimetals is to apply a sufficiently large magnetic field, under which the thermopower will grow linearly without saturation [8]. These proposals suggest feasible ways to tune the thermoelectric properties of topological semimetals.
When a conductive solid is placed under a longitudinal temperature gradient and a transverse magnetic field, two types of thermoelectric responses occur, i.e., the magneto-Seebeck effect in the longitudinal direction and the Nernst effect in the other transverse direction [9]. Both longitudinal and transverse thermoelectric effects have recently received attention in the studies of topological semimetals, specifically, studies of giant magnetic-field enhancement of the thermoelectric properties [10, 11] or exploration of the Berry curvature-related anomalous thermoelectric transport phenomena [12–18]. For instance, in the Dirac semimetal Cd3As2 [19], which has ultrahigh carrier mobility [20], anomalous magneto-Seebeck and Nernst effects were recently observed [12, 14], and the relationship between these anomalous transport properties with Berry curvature was discussed. Moreover, the magnetic-field-induced giant enhancement in both longitudinal and transverse zT values were found in Cd3As2 single crystals near room temperature [11, 21, 22]. NbP, one of the first type-I Weyl semimetals to be discovered [23–25], has recently attracted attention as a material platform for exploring the Weyl physics-related thermoelectric transport properties. Large magneto-thermopower and Nernst thermopower were observed in both single crystals and polycrystalline samples [10, 16, 26]. These findings demonstrate that topological semimetals provide fertile ground for exploring magnetic-field-mediated thermoelectric properties. Moreover, recent high-throughput searches have identified thousands of topological semimetals in the Inorganic Crystal Structure Database [27–29]. Among them, those with complex crystal structure or heavy elements would display high potential for magneto-thermoelectric conversion, as they could have an intrinsically low phonon thermal conductivity.
In this work, we study the electrical and thermal transport properties of the Dirac semimetal PtSn4 under a magnetic field. The Dirac nodal arc structure and high magnetoresistance (MR) in PtSn4 suggest that the electrical properties will respond strongly to a magnetic field [30, 31]; furthermore, the layered structure with a–c planes stacked vertically along the b axis (Figure 1(a)) and low Debye temperature of 210 K [31] suggest a low phonon thermal conductivity, which however has not been reported. In our experiments, we used PtSn4 single crystals grown from a Sn-rich binary melt [31]. The growth process and chemical and structural characterizations are described in the Methods section. The electrical resistivity ρ, thermopower S, Nernst thermopower Sxy, Hall resistivity ρH, and thermal conductivity κ were measured at various magnetic fields, B, up to 9 T. The details of the measurement procedure are also presented in the Methods section. All the transport experiments were conducted within the a–c plane of the crystals, and the magnetic field is applied along the b axis. The transport properties exhibited a dramatic response to the magnetic field below 30 K. When the magnetic field was applied, a large power factor of 80–100  μW·cm-1·K-2 and a very large suppression of the thermal conductivity appeared, which together contribute to an obvious increase in the peak zT at 15 K. Moreover, PtSn4 also exhibits a strong Nernst signal and a large Nernst power factor of 90  μW·cm-1·K-2 at 9 T and 10 K. These findings on PtSn4 provide a good paradigm for tuning highly conductive topological semimetals for simultaneous longitudinal and transverse thermoelectric energy conversion.
In the first set of transport experiments at zero magnetic field, we confirm that the PtSn4 crystals exhibit the previously observed low electrical resistivity ρ. In Figure 1(b), the measured ρ is shown as a function of T. In agreement with the literature [31], ρT at zero field increases linearly with T between 25 and 300 K, as expected for such semimetals, in which electron-phonon scattering is thought to dominate. Below 8 K, the resistivity starts to saturate, with a residual resistivity of 45 nΩ·cm at 2 K. Furthermore, a high residual resistance ratio of ρ300 K/ρ2 K≈1000 is observed, which, together with the nonsaturating MR up to 9 T, indicates a long carrier mean free path.
The absolute thermopower of PtSn4 at 0 T is much lower than that of typical thermoelectric semiconductors. ST is positive at high T and exhibits a p–n transition upon cooling (Figure 1(c)), indicating that PtSn4 is a two-carrier semimetal system. When the magnetic field is applied, S depends strongly on B at approximately 14 K, in agreement with the literature [31]. As a result, a moderate thermopower S≈−40  μV·K-1 at 9 T is obtained. Even though the magnetic field also induces strong MR, large peak power factors of 80–100  μW·cm-1·K-2, calculated by S2/ρ, are obtained under various magnetic fields (Figure 1(d)). Recalling that good thermoelectric materials generally have relatively low power factor, for example, Bi2Te3 (30–50  μW·cm-1·K-2) [32], PbTe (≈20  μW·cm-1·K-2) [33, 34], SnSe (≈10  μW·cm-1·K-2) [35], CoSb3 (30–50  μW·cm-1·K-2) [36], and half-Heusler compounds (30–50  μW·cm-1·K-2) [37], this large S2/ρ observed in PtSn4 under a magnetic field indicates its potential for thermoelectric conversion.
A large enhancement in S2/ρ is not the only required thermoelectric property; besides, the thermal conductivity should also be suppressed. We further measured the thermal conductivity κ of our samples as a function of temperature under various magnetic fields (Figure 1(e)). The experiments were performed with open electrical contact to prevent electric current flow. κT indicates a metallic T dependence, which is consistent with the ρ and S measurements. Upon warming from 2 K, κT increases linearly with T owing to the dominant impurity scattering. Near 8 K, κT reaches a maximum and then starts to decrease. Remarkably, κT exhibits a rapid decay with increasing B. A decrease in κT by more than 2 orders of magnitude is observed at 9 T and 2 K. This huge suppression of κT is a result of the giant MR, which indicates that charge carriers, rather than phonons, dominate the thermal transport in PtSn4. Owning to the magnetic-field-induced giant reduction in κ and enhancement of S2/ρ, PtSn4 exhibits a peak zT of 0.009 at 9 T and 15 K (Figure 1(f)), which is more than 30 times higher than the zT at zero field. Note that this peak in zT is obtained at a very low temperature of 15 K. The z value, a more intrinsic material parameter reflecting the thermoelectric potential, is 6×10−4 K-1 for PtSn4 at 9 T and 15 K, which is close to that of good thermoelectric materials, for example, Bi2Te3 (≈40×10−4 K-1) [32], PbTe (≈25×10−4 K-1) [33, 34], CoSb3 (≈20×10−4 K-1) [36], and half-Heusler compounds (≈10×10−4 K-1) [37]. More importantly, this very large increase in the peak zT of PtSn4 results from the simultaneous improvement of S2/ρ and suppression of κ with increasing B, which provides a good paradigm for the decoupling of the electrical and thermal transport properties.
To understand the magnetic-field-induced changes in the electrical transport properties, we further investigated the Hall resistivity ρH as a function of B at various T. Upon cooling from 300 K, ρH has a positive slope as a function of B, indicating that holes dominate the transport. Below 50 K, the slope of ρHB reverses its sign at high fields. Because dρHB/dB changes sign at low temperatures, especially around 25 K, it is tempting to associate this phenomenon with the transport contributions of both electrons and holes, which is also reflected by its thermopower at similar temperatures with almost 0  μV·K-1. Moreover, the Fermi surface of PtSn4 was calculated using density functional theory (Figure S1) and also indicates that PtSn4 is a two-carrier system with multiple electron and hole pockets.
For a more quantitative analysis of the carrier densities and mobilities, we calculated the Hall conductivity, σH=ρH/ρH2+ρ2 (Figure 2(b)) using a two-carrier model:
(1)σHB=nh2μh21+μh2B2−ne2μe21+μe2B2eB.
This model enables us to obtain the temperature-dependent average carrier densities, ne, nh and the carrier mobilities μe, μh for the electron and hole pockets, respectively. The best fits to our data indeed reveal that our PtSn4 samples exhibit parallel transport of both electrons and holes across the full temperature range investigated (Figure 2(c)), with a hole excess above 50 K and an electron excess below. The electron and hole mobilities are very high (Figure 2(c), inset) and are comparable to those of the other topological semimetals [20, 25], in which the high mobility are responsible for the giant MR observed at low T (Figure 1(b)).
After determining the carrier densities, we further investigated the thermopower as a function of B around the temperatures at which S peaks. As shown in Figure 2(d), a dramatic enhancement of S occurs with increasing B. The absolute magneto-thermopower, ∣MS∣=∣SB−S0 T/S0 T∣, becomes significant at higher magnetic fields (B>3 T), exhibiting an approximately linear relationship with B. The linear relationship at high magnetic fields can be understood in terms of the increase in the electron-phonon scattering rate with B [38], yielding |MS| ≈  ћωc/kBT for ћωc >  kBT, where ћ and kB are the reduced Planck and Boltzmann constants, respectively. In addition, ωc=eB/me/h∗ denotes the cyclotron frequency, where e is the elementary charge. For an average effective mass, me/h∗=0.2me, a linear relation between |MS| and B is expected above 3 T, in agreement with the experiments.
Considering the large carrier mobilities below 30 K and the strong response of the longitudinal thermopower to a magnetic field, it is tempting to check for the transverse thermoelectric response, i.e., the Nernst effect. The Nernst thermopower Sxy of PtSn4 at various temperatures was further measured by a standard one-heater, two-thermometer configuration. As shown in Figure 2(e), Sxy displays a normal Nernst signal, namely, an approximately linear increase upon magnetic-field application, and no saturation is found at magnetic fields of up to 9 T. At 9 T and 10.3 K, Sxy reaches a moderate value of 45  μV·K-1. Furthermore, because the electrical resistivity in the a–c plane is approximately isotropic [39], the Nernst power factor can be estimated as Sxy2/ρ (Figure 2(f)). Like the conventional power factor (Figure 1(d)), the Nernst power factor also peaks at approximately 15 K. A maximum value of approximately 90  μW·cm-1·K-2 is obtained at various magnetic fields, which is approximately 3 times larger than the value obtained in polycrystalline bulk NbP [10].
The thermal conductivity κ as a function of B is shown in Figure 3(a). At 2 K, as the magnetic field increases, κB decreases by more than 2 orders of magnitude. The phonon thermal conductivity of a metallic system typically does not change significantly under a magnetic field. The very large decrease in κB is thus a result of the large MR (Figure 1(b)), which then makes it possible to separate the phonon and electron components of the thermal conductivity. An empirical expression, κB,T=κphT+κeT/1+ηBs [40, 41], was employed to extract the phonon thermal conductivity, κphT, and electron thermal conductivity, κeT, at 0 T, where η and s are related to the thermal mobility and scattering mechanism, respectively. The obtained fitting parameters are shown in Table S1. Because this method is generally effective for large μB, only the κB,T data below 30 K were fitted. The fitted lines match the experimental data well, as shown in Figure 3(a), indicating the feasibility of this method. The extracted κeB,T decreases continuously with increasing B, as shown in Figure 3(b). At B=0 T, κeT is significantly larger than κphT, demonstrating that PtSn4 is indeed a metallic system in which charge carriers dominate the electrical and thermal transport properties. The Lorenz number L is further calculated according to the Wiedemann–Franz (WF) law [1], as shown in Figure 3(c). At B=0 T, this is a downward violation of the WF law, whereas an upward violation is found when the magnetic field is applied. Violations of the WF law typically indicate inelastic electron-phonon scattering or hydrodynamic transport, as recently found in the Weyl semimetal WP2 [42, 43]. Moreover, in a very recent work on another Weyl semimetal system, TaP, Han et al. also observed an upward violation of the WF law [40]. The reason is still not clear, but it seems that violation of the WF law under a magnetic field is common in topological semimetals.
In summary, measurements of the electrical and thermal transport properties established PtSn4 as a distinctive platform by exhibiting strong regulation of the two-carrier transport behavior under both a thermal gradient and a magnetic field. PtSn4 is a highly conductive topological semimetal with low electrical resistivity at liquid helium temperatures, which is comparable to that of many well-established metals or topological semimetals [44]. Hall effect measurement of PtSn4 revealed a two-carrier behavior with both high electron and high hole mobilities. At zero magnetic field, the thermopower is close to zero, and the thermal conductivity is orders of magnitude higher than that of good thermoelectric semiconductors. These features indicate that PtSn4 has a poor thermoelectric performance.
However, all these transport properties change significantly when a magnetic field is applied. Large Seebeck and Nernst power factors and a huge suppression of the thermal conductivity are simultaneously realized under various magnetic fields, providing a good example for decoupling the electrical and thermal transport properties of semimetals. These dramatic changes in the transport properties are the result of the regulation of the transport behavior of the two types of carriers under a magnetic field. At zero magnetic field, the thermal gradient drives the accumulation of both electrons and holes on the cold side, which balance each other’s contributions to the Seebeck thermopower. When a magnetic field is applied, the electrons and holes exhibit different transport behaviors, which makes it possible to realize strong thermoelectric responses in both the longitudinal and transverse directions. These results on PtSn4 provide a paradigm for tuning highly conductive semimetals for both longitudinal and transverse thermoelectric conversion by applying a magnetic field. Interestingly, some recent work had paid attention to the relationship between thermoelectric performance and internal magnetic interactions, for example, superparamagnetic behavior [45], paramagnon drag [46], and spin fluctuation [47]. These works together with our current study on PtSn4 demonstrate that introducing magnetic interaction as an additional influence on the transport properties, either by applying an external magnetic field or by introducing an internal magnetic moment, could open a new direction in thermoelectric research.
Single crystals of PtSn4 were grown from a Sn-rich binary melt as described in the literature [31]. The high-purity starting elements, Pt (shot, 99.99%) and Sn (shot, 99.999%), were mixed with an initial stoichiometry of Pt4Sn96; the mixture was placed in an alumina crucible, which was sealed in a quartz tube under partial Ar pressure. The quartz tube was heated to 600°C over a period of 5 h and held at that temperature for 20 h. Next, it was slowly cooled to 350°C over a period of 60 h. The excess Sn flux was removed using a centrifuge at 400°C. After centrifugation, the remaining flux on the surface was removed by mechanical polishing.
Powder X-ray diffraction measurement of PtSn4 was performed using Cu Kα radiation at room temperature to identify the phase purity and crystal structure. An image-plate Huber G670 Guinier camera was used in a diffraction range of 10°≤2θ≤100° in steps of 0.005°. Scanning electron microscopy (SEM) with energy-dispersive X-ray spectrometry (EDXS) was used for elemental analysis. Single-crystal X-ray diffraction measurements were performed using a Bruker D8 Venture diffractometer with Mo Kα radiation and the SHELX97 software was used for structure refinement [48]. More information about the crystallographic and refinement parameters can be found in our previous work [49], where the studied PtSn4 single crystal is from the same batch with the current work. The crystal structure is described by the centrosymmetric space group Ccca, in agreement with the literature [50]. Figure 1(a) shows the layered crystal structure of PtSn4, which consists of PtSn4 slabs constructed from eight-fold Sn-coordinated Pt atoms. The layered structure is visible in the SEM results, as shown in Figure S2. The layered nature of PtSn4 allows for slight disorder in the ac plane, i.e., a small misalignment between consecutive PtSn4 layers.
The powder X-ray diffraction pattern of PtSn4 is shown in Figure S3. The diffraction peaks can be well indexed to orthorhombic structure, in good agreement with the single-crystal X-ray diffraction results [49]. No other obvious phases are observed. The actual composition of the PtSn4 single crystal is determined by EDXS at seven randomly selected positions; the result agrees with the nominal composition within the instrument error, as shown in Table S2. High-resolution transmission electron microscopy (HRTEM) (Figure S4) of a 6.7 μm×4.4  μm lamella showed the good crystallinity of the PtSn4 sample (Figure S5).
The temperature-dependent thermal conductivity and thermopower under a magnetic field were jointly measured adiabatically by the one-heater, two-thermometer configuration using the thermal transport option of the PPMS (Quantum Design), in which the sample was placed so that the magnetic field was perpendicular to the heat flow. The thermometers were calibrated under the magnetic field using the PPMS MR calibration wizard before the thermal transport measurements. To ensure uniform heat flow through the bar-shaped sample, two gold-plated copper leads were attached to both ends of the sample using silver epoxy and then connected to the heater and sink, respectively. Two other copper leads were wrapped around and glued to the sample with silver epoxy for detecting ΔV and ΔT. The applied temperature gradients were approximately 1%–3% of the base temperature. We then investigated the possible effect of the thermal contact resistances and demonstrated the need for careful contact preparation. After careful contact preparation, as described above, we investigated samples with lengths ranging from 4.5 to 7 mm, but similar cross-sections and contact areas. We obtained consistent results for all the samples at any magnetic field or temperature investigated, and therefore did not observe any indication of diminished thermal conductivity owing to contact. The Nernst thermopower was also measured adiabatically in the one-heater, two-thermometer configuration using the PPMS. The Nernst signal was estimated as, Sxy=LxVy/LyΔTx, where Lx is the distance between the two temperature leads, Ly is the distance between the two voltage wires, Vy is the transverse electric voltage, and ΔTx is the measured temperature difference. The measured raw Nernst thermopower data were antisymmetrized to correct for contact misalignment.
Both the longitudinal and Hall resistivities were measured by a standard four-probe method using the AC transport option in the PPMS system with an applied AC current of 16 mA. Point contacts for Hall voltage probes were obtained by spot-welding 25  μm platinum wires. For the current and longitudinal voltage probes, linear contacts were made using silver paint and platinum wires. To correct for contact misalignment, the measured Hall resistivity was field antisymmetrized. For all the transport measurements, the magnetic field was applied along the b axis, which was perpendicular to the a–c plane.
  • The Netherlands Organization for Science NWO(022.005.006)
  • Deutsche Forschungsgemeinschaft(314790414)
  • Alexander von Humboldt-Stiftung
  • H2020 European Research Council(742068)
1
Goldsmid H. J. Introduction of Thermoelectricity, Springer, Heidelberg, 2010
2
Behnia K. Fundamentals of Thermoelectricity, Oxford University Press, Oxford, 2015
3
Zhu T., Liu Y., Fu C., Heremans J. P., Snyder J. G., and Zhao X., “Compromise and synergy in high-efficiency thermoelectric materials,” Advanced Materials, vol. 29, no. 14, article 1605884, 2017
4
Mori T., “Novel principles and nanostructuring methods for enhanced thermoelectrics,” Small, vol. 13, no. 45, article 1702013, 2017
5
Mao J., Liu Z., Zhou J., Zhu H., Zhang Q., Chen G., and Ren Z., “Advances in thermoelectrics,” Advances in Physics, vol. 67, no. 2, pp. 69–147, 2018
6
Markov M., Hu X., Liu H. C., Liu N., Poon S. J., Esfarjani K., and Zebarjadi M., “Semi-metals as potential thermoelectric materials,” Scientific Reports, vol. 8, no. 1, p. 9876, 2018
7
Mao J., Zhu H., Ding Z., Liu Z., Gamage G. A., Chen G., and Ren Z., “High thermoelectric cooling performance of n-type Mg3Bi2-based materials,” Science, vol. 365, no. 6452, pp. 495–498, 2019
8
Skinner B., and Fu L., “Large, nonsaturating thermopower in a quantizing magnetic field,” Science Advances, vol. 4, no. 5, article eaat2621, 2018
9
Behnia K., and Aubin H., “Nernst effect in metals and superconductors: a review of concepts and experiments,” Reports on Progress in Physics, vol. 79, no. 4, article 046502, 2016
10
Fu C., Guin S. N., Watzman S. J., Li G., Liu E., Kumar N., Süβ V., Schnelle W., Auffermann G., Shekhar C., Sun Y., Gooth J., and Felser C., “Large Nernst power factor over a broad temperature range in polycrystalline Weyl semimetal NbP,” Energy & Environmental Science, vol. 11, no. 10, pp. 2813–2820, 2018
11
Wang H., Luo X., Chen W., Wang N., Lei B., Meng F., Shang C., Ma L., Wu T., Dai X., Wang Z., and Chen X., “Magnetic-field enhanced high-thermoelectric performance in topological Dirac semimetal Cd3As2 crystal,” Science Bulletin, vol. 63, no. 7, pp. 411–418, 2018
12
Jia Z., Li C., Li X., Shi J., Liao Z., Yu D., and Wu X., “Thermoelectric signature of the chiral anomaly in Cd3As2,” Nature Communications, vol. 7, no. 1, article 13013, 2016
13
Li X., Xu L., Ding L., Wang J., Shen M., Lu X., Zhu Z., and Behnia K., “Anomalous Nernst and Righi-Leduc effects inMn3Sn: Berry curvature and entropy flow,” Physical Review Letters, vol. 119, no. 5, article 056601, 2017
14
Liang T., Lin J., Gibson Q., Gao T., Hirschberger M., Liu M., Cava R. J., and Ong N. P., “Anomalous Nernst Effect in the Dirac Semimetal Cd3As2,” Physical Review Letters, vol. 118, no. 13, article 136601, 2017
15
Sakai A., Mizuta Y. P., Nugroho A. A., Sihombing R., Koretsune T., Suzuki M. T., Takemori N., Ishii R., Nishio-Hamane D., Arita R., Goswami P., and Nakatsuji S., “Giant anomalous Nernst effect and quantum-critical scaling in a ferromagnetic semimetal,” Nature Physics, vol. 14, no. 11, pp. 1119–1124, 2018
16
Watzman S. J., McCormick T. M., Shekhar C., Wu S. C., Sun Y., Prakash A., Felser C., Trivedi N., and Heremans J. P., “Dirac dispersion generates unusually large Nernst effect in Weyl semimetals,” Physical Review B, vol. 97, no. 16, article 161404, 2018
17
Guin S. N., Manna K., Noky J., Watzman S. J., Fu C., Kumar N., Schnelle W., Shekhar C., Sun Y., Gooth J., and Felser C., “Anomalous Nernst effect beyond the magnetization scaling relation in the ferromagnetic Heusler compound Co2MnGa,” NPG Asia Materials, vol. 11, no. 1, article 16, 2019
18
Guin S. N., Vir P., Zhang Y., Kumar N., Watzman S. J., Fu C., Liu E., Manna K., Schnelle W., Gooth J., Shekhar C., Sun Y., and Felser C., “Zero-field Nernst effect in a ferromagnetic Kagome-Lattice Weyl-semimetal Co3Sn2S2,” Advanced Materials, vol. 31, no. 25, article 1806622, 2019
19
Wang Z., Weng H., Wu Q., Dai X., and Fang Z., “Three-dimensional Dirac semimetal and quantum transport in Cd3As2,” Physical Review B, vol. 88, no. 12, article 125427, 2013
20
Liang T., Gibson Q., Ali M. N., Liu M., Cava R. J., and Ong N. P., “Ultrahigh mobility and giant magnetoresistance in the Dirac semimetal Cd3As2,” Nature Materials, vol. 14, no. 3, pp. 280–284, 2014
21
Wang H., Luo X., Peng K., Sun Z., Shi M., Ma D., Wang N., Wu T., Ying J., Wang Z., and Chen X., “Magnetic field-enhanced thermoelectric performance in Dirac semimetal Cd3As2 crystals with different carrier concentrations,” Advanced Functional Materials, vol. 29, no. 37, article 1902437, 2019
22
Xiang J., Hu S. L., Lyu M., Zhu W. L., Ma C. Y., Chen Z. Y., Steglich F., Chen G. F., and Sun P. J., “Large transverse thermoelectric figure of merit in a topological Dirac semimetal,” Science China Physics, Mechanics & Astronomy, vol. 63, no. 3, article 237011, 2020
23
Weng H., Fang C., Fang Z., Bernevig B. A., and Dai X., “Weyl semimetal phase in noncentrosymmetric transition-metal monophosphides,” Physical Review X, vol. 5, no. 1, article 011029, 2015
24
Xu S.-Y., Belopolski I., Alidoust N., Neupane M., Bian G., Zhang C., Sankar R., Chang G., Yuan Z., Lee C. C., Huang S. M., Zheng H., Ma J., Sanchez D. S., Wang B., Bansil A., Chou F., Shibayev P. P., Lin H., Jia S., and Hasan M. Z., “Discovery of a Weyl fermion semimetal and topological Fermi arcs,” Science, vol. 349, no. 6248, pp. 613–617, 2015
25
Shekhar C., Nayak A. K., Sun Y., Schmidt M., Nicklas M., Leermakers I., Zeitler U., Skourski Y., Wosnitza J., Liu Z., Chen Y., Schnelle W., Borrmann H., Grin Y., Felser C., and Yan B., “Extremely large magnetoresistance and ultrahigh mobility in the topological Weyl semimetal candidate NbP,” Nature Physics, vol. 11, no. 8, pp. 645–649, 2015
26
Stockert U., Dos Reis R. D., Ajeesh M. O., Watzman S. J., Schmidt M., Shekhar C., Heremans J. P., Felser C., Baenitz M., and Nicklas M., “Thermopower and thermal conductivity in the Weyl semimetal NbP,” Journal of Physics: Condensed Matter, vol. 29, no. 32, article 325701, 2017
27
Vergniory M. G., Elcoro L., Felser C., Regnault N., Bernevig B. A., and Wang Z., “A complete catalogue of high-quality topological materials,” Nature, vol. 566, no. 7745, pp. 480–485, 2019
28
Tang F., Po H. C., Vishwanath A., and Wan X., “Comprehensive search for topological materials using symmetry indicators,” Nature, vol. 566, no. 7745, pp. 486–489, 2019
29
Zhang T., Jiang Y., Song Z., Huang H., He Y., Fang Z., Weng H., and Fang C., “Catalogue of topological electronic materials,” Nature, vol. 566, no. 7745, pp. 475–479, 2019
30
Wu Y., Wang L. L., Mun E., Johnson D. D., Mou D., Huang L., Lee Y., Bud’ko S. L., Canfield P. C., and Kaminski A., “Dirac node arcs in PtSn4,” Nature Physics, vol. 12, no. 7, pp. 667–671, 2016
31
Mun E., Ko H., Miller G. J., Samolyuk G. D., Bud'ko S. L., and Canfield P. C., “Magnetic field effects on transport properties of PtSn4,” Physical Review B, vol. 85, no. 3, article 035135, 2012
32
Poudel B., Hao Q., Ma Y., Lan Y., Minnich A., Yu B., Yan X., Wang D., Muto A., Vashaee D., Chen X., Liu J., Dresselhaus M. S., Chen G., and Ren Z., “High-thermoelectric performance of nanostructured bismuth antimony telluride bulk alloys,” Science, vol. 320, no. 5876, pp. 634–638, 2008
33
Pei Y., Shi X., LaLonde A., Wang H., Chen L., and Snyder G. J., “Convergence of electronic bands for high performance bulk thermoelectrics,” Nature, vol. 473, no. 7345, pp. 66–69, 2011
34
Biswas K., He J., Blum I. D., Wu C. I., Hogan T. P., Seidman D. N., Dravid V. P., and Kanatzidis M. G., “High-performance bulk thermoelectrics with all-scale hierarchical architectures,” Nature, vol. 489, no. 7416, pp. 414–418, 2012
35
Shang P.-P., Dong J., Pei J., Sun F. H., Pan Y., Tang H., Zhang B. P., Zhao L. D., and Li J. F., “Highly textured N-type SnSe polycrystals with enhanced thermoelectric performance,” Research, vol. 2019, article 9253132, –10, 2019
36
Shi X., Yang J., Salvador J. R., Chi M., Cho J. Y., Wang H., Bai S., Yang J., Zhang W., and Chen L., “Multiple-filled Skutterudites: high thermoelectric figure of merit through separately optimizing electrical and thermal transports,” Journal of the American Chemical Society, vol. 133, no. 20, pp. 7837–7846, 2011
37
Fu C., Zhu T., Liu Y., Xie H., and Zhao X., “Band engineering of high performance p-type FeNbSb based half-Heusler thermoelectric materials for figure of merit zT > 1,” Energy & Environmental Science, vol. 8, no. 1, pp. 216–220, 2015
38
Ohta T., “Phonon-drag Seebeck effect in a strong magnetic field (1) longitudinal case,” Journal of the Physical Society of Japan, vol. 18, no. 8, pp. 1166–1173, 1963
39
Inamdar M., Kriegisch M., Shafeek L., Sidorenko A., Müller H., Prokofiev A., Blaha P., and Paschen S., “Quantum oscillations in ultra pure PtSn4,” Solid State Phenomena, vol. 194, pp. 88–91, 2012
40
Han F., Andrejevic N., Nguyen T., Kozii V., Nguyen Q., Ding Z., Pablo-Pedro R., Parjan S., Skinner B., Alatas A., and Alp E., “Discovery of giant, non-saturating thermopower in topological semimetal at quantum limit,” 2019, http://arxiv.org/abs/1904.03179.
41
Ocaña R., and Esquinazi P., “Thermal conductivity tensor in YBa2Cu3O7−x: effects of a planar magnetic field,” Physical Review B, vol. 66, no. 6, 2002
42
Gooth J., Menges F., Kumar N., Süβ V., Shekhar C., Sun Y., Drechsler U., Zierold R., Felser C., and Gotsmann B., “Thermal and electrical signatures of a hydrodynamic electron fluid in tungsten diphosphide,” Nature Communications, vol. 9, no. 1, article 4093, 2018
43
Jaoui A., Fauqué B., Rischau C. W., Subedi A., Fu C., Gooth J., Kumar N., Süß V., Maslov D. L., Felser C., and Behnia K., “Departure from the Wiedemann–Franz law in WP2 driven by mismatch in T-square resistivity prefactors,” npj Quantum Materials, vol. 3, no. 1, article 64, 2018
44
Hu J., Xu S. Y., Ni N., and Mao Z., “Transport of topological semimetals,” Annual Review of Materials Research, vol. 49, no. 1, pp. 207–252, 2019
45
Zhao W., Liu Z., Sun Z., Zhang Q., Wei P., Mu X., Zhou H., Li C., Ma S., He D., Ji P., Zhu W., Nie X., Su X., Tang X., Shen B., Dong X., Yang J., Liu Y., and Shi J., “Superparamagnetic enhancement of thermoelectric performance,” Nature, vol. 549, no. 7671, pp. 247–251, 2017
46
Zheng Y., Lu T., Polash M. M. H., Rasoulianboroujeni M., Liu N., Manley M. E., Deng Y., Sun P. J., Chen X. L., Hermann R. P., Vashaee D., Heremans J. P., and Zhao H., “Paramagnon drag in high thermoelectric figure of merit Li-doped MnTe,” Science Advances, vol. 5, no. 9, article eaat9461, 2019
47
Tsujii N., Nishide A., Hayakawa J., and Mori T., “Observation of enhanced thermopower due to spin fluctuation in weak itinerant ferromagnet,” Science Advances, vol. 5, no. 2, article eaat5935, 2019
48
Sheldrick G. M. Program for Crystal Structure Refinement, University of Göttingen, Göttingen, 1997
49
Li G., Fu C., Shi W., Jiao L., Wu J., Yang Q., Saha R., Kamminga M. E., Srivastava A. K., Liu E., Yazdani A. N., Kumar N., Zhang J., Blake G. R., Liu X., Fahlman M., Wirth S., Auffermann G., Gooth J., Parkin S., Madhavan V., Feng X., Sun Y., and Felser C., “Dirac nodal arc semimetal PtSn4: an ideal platform for understanding surface properties and catalysis for hydrogen evolution,” Angewandte Chemie, vol. 131, no. 37, pp. 13241–13246, 2019
50
Künnen B., Niepmann D., and Jeitschko W., “Structure refinements and some properties of the transition metal stannides Os3Sn7, Ir5Sn7, Ni0.402(4)Pd0.598Sn4, α-PdSn2 and PtSn4,” Journal of Alloys and Compounds, vol. 309, no. 1-2, pp. 1–9, 2000
Year 2020 volume 2020 Issue 4
PDF
54
31
Cite this Article
BibTeX
Article Info
doi: 10.34133/2020/4643507
  • Receive Date:2019-12-26
  • Online Date:2026-10-27
  • Published:2020-04-20
Article Data
Affiliations
History
  • Received:2019-12-26
  • Accepted:2020-02-17
Funding
The Netherlands Organization for Science NWO(022.005.006)
Deutsche Forschungsgemeinschaft(314790414)
Alexander von Humboldt-Stiftung
H2020 European Research Council(742068)
Affiliations
    1Max Planck Institute for Chemical Physics of Solids, 01187 Dresden, Germany
    2Department of Physics, University of California, Berkeley, CA 94720, USA
    3Department of Physics, University of Toronto, Toronto, Ontario M5S 1A7, Canada
    4Max Planck Institute of Microstructure Physics, 06120 Halle, Germany
    5Department of Mechanical and Materials Engineering, University of Cincinnati, Cincinnati, OH 45219, USA
    6Institute of Physics, Martin Luther University Halle-Wittenberg, 06120 Halle, Germany
References
Share
https://castjournals.cast.org.cn/joweb/research/EN/10.34133/2020/4643507
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family
属数
Number of
genus
种数
Number of
species
占总种数比例
Percentage of
total species (%)
属
Genus
种数
Number of
species
占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT