收藏切换
Effect of Laser Scanning Speed on Microstructure and Hardness of Laser Cladded 316L Coating
收藏切换
PDF
Tianzhu HE1, Zhe WU1, Chengwu ZHANG2, Dongsheng CHEN3
Mining and Metallurgical Engineering | 2023, 43(5) : 159 - 163
Less
收藏切换
Mining and Metallurgical Engineering | 2023, 43(5): 159-163
MATERIALS
Effect of Laser Scanning Speed on Microstructure and Hardness of Laser Cladded 316L Coating
Full
Tianzhu HE1, Zhe WU1, Chengwu ZHANG2, Dongsheng CHEN3
Affiliations
  • 1.Hebei Institute of Mechanical and Electrical Engineering Technician, Zhangjiakou 075000, Hebei, China
  • 2.School of Mechanical Engineering, University of South China, Hengyang 421001, Hunan, China
  • 3.SAIC Volkswagen Automotive Co Ltd, Shanghai 201805, China
Published: 2023-10-01 doi: 10.3969/j.issn.0253-6099.2023.05.036
Outline
收藏切换

316L stainless steel coatings were prepared on the surface of 304 stainless steel by using laser cladding at different scanning speed, and then metallographic microscopy, X-ray diffractometer, scanning electron microscopy and microhardness tester were adopted respectively to investigate the macroscopic morphology, phase composition, microscopic structure and microhardness for the coatings. The results showed that the 316L coating had a single-phase austenitic structure, and as the scanning speed increased, the grain size of the coating became smaller due to the reduction in the laser power density and heat input, and an increase in the cooling speed. It is found that the microhardness of the coatings is positively correlated with scanning speed, and the 316L coatings prepared by laser cladding at a scanning speed of 1 400 mm/min presents the highest microhardness of about 275HV0.3. The improvement of the microhardness of the coating is ascribed to the effect of solid solution strengthening caused by lattice distortion combined with the effect of fine crystal strengthening. The wear test showed that the average friction coefficient of 316L coatings was significantly lower than that of 304 stainless steel substrate. And the 316L coating prepared by laser cladding at 1 400 mm/min has a friction coefficient of 0.424 and wear rate of 2.29 × 10-6 mm3/(N·m), and is prone to abrasive wear.

laser cladding  /  microhardness  /  316L stainless steel  /  scanning speed  /  wear resistance  /  laser cladded coating
Tianzhu HE, Zhe WU, Chengwu ZHANG, Dongsheng CHEN. Effect of Laser Scanning Speed on Microstructure and Hardness of Laser Cladded 316L Coating[J]. Mining and Metallurgical Engineering, 2023 , 43 (5) : 159 -163 . DOI: 10.3969/j.issn.0253-6099.2023.05.036
Year 2023 volume 43 Issue 5
PDF
36
9
Cite this Article
BibTeX
Article Info
doi: 10.3969/j.issn.0253-6099.2023.05.036
  • Receive Date:2023-04-22
  • Online Date:2026-03-05
  • Published:2023-10-01
Article Data
Affiliations
History
  • Received:2023-04-22
Funding
Affiliations
    1.Hebei Institute of Mechanical and Electrical Engineering Technician, Zhangjiakou 075000, Hebei, China
    2.School of Mechanical Engineering, University of South China, Hengyang 421001, Hunan, China
    3.SAIC Volkswagen Automotive Co Ltd, Shanghai 201805, China
References
Share
https://castjournals.cast.org.cn/joweb/kygczz/EN/10.3969/j.issn.0253-6099.2023.05.036
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数

Family
属数
Number of
genus
种数
Number of
species
占总种数比例
Percentage of
total species (%)

Genus
种数
Number of
species
占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT