收藏切换
Numerical simulation of deformation and stress processes in fault–bend folding: Quantitative constraints based on elastoplastic parameter control
收藏切换
Jia MA1, 2, Xiaochen WANG3, Dengfa HE1, *, Weikang ZHANG1, Guo LU1, Hanyu HUANG4, Chiyue LIU1
Journal of Geomechanics | 2025, 31(6) : 1310 - 1329
Less
收藏切换
Journal of Geomechanics | 2025, 31(6): 1310-1329
Numerical simulation of deformation and stress processes in fault–bend folding: Quantitative constraints based on elastoplastic parameter control
Full
Jia MA1, 2, Xiaochen WANG3, Dengfa HE1, *, Weikang ZHANG1, Guo LU1, Hanyu HUANG4, Chiyue LIU1
Affiliations
  • 1Institute of Energy , China University of Geosciences (Beijing), Beijing 100083, China
  • 2Chengdu Research Institute of Exploration and Development, Daqing Oilfield Limited Company, Chengdu 610051, Sichuan, China
  • 3Chongqing Branch, Daqing Oilfield Limited Company, Chongqing 402660, China
  • 4Institute of Sedimentary Geology, Chengdu University of Technology, Chengdu 610059, Sichuan, China
Published: 2025-12-28 doi: 10.12090/j.issn.1006-6616.2025093
Outline
收藏切换
Objective

Fault–bend folds, characteristic structures in fold-and-thrust belts, act as key kinematic units in the analysis of compressional deformation and form structural traps at flat–ramp transitions. This makes them critical targets in the exploration of hydrocarbons in foreland basins.

Methods

Using Suppe’s theoretical model and finite element simulations, we developed a geomechanical model with realistic rock properties. We defined boundary conditions for fold formation and analyzed stress-strain patterns during the evolution of fault–bend folds. We applied the Mohr-Coulomb model to assess six parameters—density (ρ), Young’s modulus (E), Poisson’s ratio (υ), internal friction angle (ϕ), cohesion (c), and dilation angle (ψ)—for identifying dominant controls.

Results

Open boundaries enable the development of fault-bend folds consistent with classical models, whereas fixed boundaries cause marked forelimb tilting and non-classical deformation. Stress-strain partitioning is distinct: Fold limbs and the upper ramp experience compression; the core and upper flat undergo extension. Both axial surfaces show upward-decreasing stress concentrations and plastic strain. The lower axial surface builds the backlimb and initiates shear fracturing; the upper axial surface shapes the anticlinal core and forelimb under tension, developing potential fracture systems. Cohesion (c) and the internal friction angle (ϕ) are key factors governing fold wavelength and forelimb steepness, respectively, with nonlinear threshold behaviors. Young’s modulus and dilation angle have localized, minor influence. Density and Poisson’s ratio show negligible effects.

Conclusion

Fault–bend folding is a progressive deformation process in which strata adjust to adapt to the geometry of pre-existing faults under compressive stress. This results in a kinematic sequence from initial slip and backlimb growth, through fold nucleation and propagation, to final stabilization with complex derived structures. Cohesion and the internal friction angle are the decisive controlling parameters.

Significance

This numerical analysis clarifies the development mechanisms, stress–strain organization, and controlling factors of fault–bend folds, deepening the theoretical understanding of compressional tectonic deformation.

fault–bend fold  /  Mohr-Coulomb elastoplastic criterion  /  stress–strain characteristics  /  tectonic deformation  /  finite element numerical simulation
马佳, 王孝臣, 何登发, 张伟康, 鲁国, 黄涵宇, 刘驰悦. 断层转折褶皱形变与应力过程数值模拟研究:基于弹塑性参数控制的定量约束. 地质力学学报, 2025 , 31 (6) : 1310 -1329 . DOI: 10.12090/j.issn.1006-6616.2025093
Jia MA, Xiaochen WANG, Dengfa HE, Weikang ZHANG, Guo LU, Hanyu HUANG, Chiyue LIU. Numerical simulation of deformation and stress processes in fault–bend folding: Quantitative constraints based on elastoplastic parameter control[J]. Journal of Geomechanics, 2025 , 31 (6) : 1310 -1329 . DOI: 10.12090/j.issn.1006-6616.2025093
  • This research is financially supported by the Key Program of the National Natural Science Foundation of China (Grant No. 42330810).
Year 2025 volume 31 Issue 6
66
29
Cite this Article
BibTeX
Article Info
doi: 10.12090/j.issn.1006-6616.2025093
  • Receive Date:2025-07-28
  • Online Date:2026-11-13
  • Published:2025-12-28
Article Data
Affiliations
History
  • Received:2025-07-28
  • Revised:2025-10-17
  • Accepted:2025-11-03
Funding
This research is financially supported by the Key Program of the National Natural Science Foundation of China (Grant No. 42330810).
Affiliations
    1Institute of Energy , China University of Geosciences (Beijing), Beijing 100083, China
    2Chengdu Research Institute of Exploration and Development, Daqing Oilfield Limited Company, Chengdu 610051, Sichuan, China
    3Chongqing Branch, Daqing Oilfield Limited Company, Chongqing 402660, China
    4Institute of Sedimentary Geology, Chengdu University of Technology, Chengdu 610059, Sichuan, China
References
Share
https://castjournals.cast.org.cn/joweb/dzlxxb/EN/10.12090/j.issn.1006-6616.2025093
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family
属数
Number of
genus
种数
Number of
species
占总种数比例
Percentage of
total species (%)
属
Genus
种数
Number of
species
占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT