收藏切换
A method for determining characteristic pressure parameters during hydraulic fracturing based on linearized fitting
收藏切换
Haifan XIAO1, Ningyu WU1, Guiyun GAO1, *, Jikun LIU2, Xinshuai YANG2, Xiaopan HUANG1
Journal of Geomechanics | 2025, 31(6) : 1282 - 1295
Less
收藏切换
Journal of Geomechanics | 2025, 31(6): 1282-1295
A method for determining characteristic pressure parameters during hydraulic fracturing based on linearized fitting
Full
Haifan XIAO1, Ningyu WU1, Guiyun GAO1, *, Jikun LIU2, Xinshuai YANG2, Xiaopan HUANG1
Affiliations
  • 1National Institute of Natural Hazards, Ministry of Emergency Management, Beijing 100085, China
  • 2School of Engineering and Technology, China University of Geosciences (Beijing), Beijing 100083, China
Published: 2025-12-28 doi: 10.12090/j.issn.1006-6616.2025091
Outline
收藏切换
Objective

Hydraulic fracturing is a fundamental technique for in-situ stress measurement, yet conventional methods of interpreting the instantaneous shut-in pressure (ps) and reopening pressure (pr) are often sensitive to noise, strongly subjective, and inadequate for facing nonlinear pressure–time responses. To address the lack of objective, robust, and high-accuracy identification methods, this study proposes a linearized curve-fitting approach capable of automatically determining key characteristic pressures from complex fracturing curves.

Methods

The method transforms a nonlinear pressure–time curve into multiple locally linear segments through polynomial smoothing, adaptive sliding-window regression, and statistical slope-change detection. Significant slope mutations are used to automatically identify ps during the shut-in decay stage and pr during the re-pressurization stage. The method is validated using true-triaxial hydraulic fracturing laboratory tests on granite and field tests at the Jizhou pumped-storage power station (75–277 m depth).

Results

Across six granite specimens (HF2–HF9), the proposed method consistently produced pr values between those obtained by the single-tangent and shifted-pb methods, avoiding the low–high systematic bias of the two techniques. For ps, the method yielded similar or more conservative results than traditional methods, with most absolute deviations <0.40 MPa. The method demonstrated strong consistency across varying stress states and significantly reduced subjective scatter. The principal stresses calculated from ps and pr showed physically reasonable trends. The σ1 errors were <30% in most cases and the behavior was stable without random jumps, indicating improved objectivity of the automated identification. In the four tested depth intervals of the LFZK02 borehole, pr and ps determined by traditional methods exhibited large spreads (e.g., pr deviations >1.5 MPa and ps deviations up to 0.74 MPa). In contrast, the linearized method consistently produced values close to the multi-method averages and with much smaller dispersion. For ps, deviations relative to Muskat and derivative methods were typically <0.20 MPa. Using the automatically identified ps and pr, the derived principal stresses showed a clear horizontally compressive regime (SH=6.55–9.85 MPa; Sh=3.54–6.21 MPa), matching regional stress data and confirming the reliability of the method in actual field conditions.

Conclusion

The linearized curve-fitting method effectively overcomes the subjectivity, noise sensitivity, and model-dependence of conventional hydraulic-fracturing interpretation approaches. This method provides stable, accurate, and repeatable identification of ps and pr in both laboratory and field environments and maintains good performance under nonlinear responses, data disturbance, and multi-cycle loading–unloading conditions. [Significance] This study offers a robust, automated, and universally applicable tool for interpreting hydraulic-fracturing pressure curves, significantly enhancing the reliability of in-situ stress measurements and supporting the development of intelligent, standardized stress-testing systems for underground engineering.

linearized curve fitting method  /  reopening pressure (pr)  /  instantaneous shut-in pressure (ps)  /  hydraulic fracturing  /  in-situ stress measurement
肖海帆, 武凝雨, 高桂云, 刘冀昆, 杨鑫帅, 黄晓盼. 基于线性化拟合的水压致裂特征压力参数判定方法. 地质力学学报, 2025 , 31 (6) : 1282 -1295 . DOI: 10.12090/j.issn.1006-6616.2025091
Haifan XIAO, Ningyu WU, Guiyun GAO, Jikun LIU, Xinshuai YANG, Xiaopan HUANG. A method for determining characteristic pressure parameters during hydraulic fracturing based on linearized fitting[J]. Journal of Geomechanics, 2025 , 31 (6) : 1282 -1295 . DOI: 10.12090/j.issn.1006-6616.2025091
  • This research is financially supported by the National Natural Science Foundation of China (Grant No. 42174118).
Year 2025 volume 31 Issue 6
51
21
Cite this Article
BibTeX
Article Info
doi: 10.12090/j.issn.1006-6616.2025091
  • Receive Date:2025-07-27
  • Online Date:2026-11-13
  • Published:2025-12-28
Article Data
Affiliations
History
  • Received:2025-07-27
  • Revised:2025-10-13
  • Accepted:2025-10-22
Funding
This research is financially supported by the National Natural Science Foundation of China (Grant No. 42174118).
Affiliations
    1National Institute of Natural Hazards, Ministry of Emergency Management, Beijing 100085, China
    2School of Engineering and Technology, China University of Geosciences (Beijing), Beijing 100083, China
References
Share
https://castjournals.cast.org.cn/joweb/dzlxxb/EN/10.12090/j.issn.1006-6616.2025091
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family
属数
Number of
genus
种数
Number of
species
占总种数比例
Percentage of
total species (%)
属
Genus
种数
Number of
species
占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT