收藏切换
Refined characterization and analysis of shallow crustal stresses based on hydraulic fracturing data
收藏切换
Sijie XIONG1, 2, Xiaodong MA1, 2, *, Yuehui YANG3, 4, Bangchen WU3, 4, Awei LI3, 4, Dongsheng SUN3, 4
Journal of Geomechanics | 2026, 32(2) : 414 - 426
Less
收藏切换
Journal of Geomechanics | 2026, 32(2): 414-426
• Crustal Stress & Tectonic Stress Field •
Refined characterization and analysis of shallow crustal stresses based on hydraulic fracturing data
Full
Sijie XIONG1, 2, Xiaodong MA1, 2, *, Yuehui YANG3, 4, Bangchen WU3, 4, Awei LI3, 4, Dongsheng SUN3, 4
Affiliations
  • 1State Key Laboratory of Precision Geodesy, Hefei 230026, Anhui, China
  • 2School of Earth and Space Sciences, University of Science and Technology of China, Hefei 230026, Anhui, China
  • 3Institute of Geomechanics, Chinese Academy of Geological Sciences, Beijing 100081, China
  • 4Engineering Technology Innovation Center of In-situ Stress, Ministry of Natural Resources, Beijing 100081, China
Published: 2026-04-28 doi: 10.12090/j.issn.1006-6616.2025096
Outline
收藏切换
Objective

In-situ stress field characterization is crucial for underground engineering safety, rock stability evaluation, and resource development. Current research in Guangdong Province is mainly concentrated on deep crustal levels, where stress interpretations predominantly rely on focal mechanism inversion and numerical modelling, while shallow stress conditions (<500 m) remain insufficiently constrained due to a lack of direct measurements and fine-scale analysis. To address this gap, this study constructs a shallow stress profile for two boreholes (ZK1 and ZK2, both < 500 m deep) in central–southern Guangdong using hydraulic fracturing and ultrasonic imaging data, aiming to refine shallow stress magnitudes, orientations, and occurrence mechanisms.

Methods

Borehole imaging was applied to record hydraulic fracture morphology before and after pressurization, ensuring accurate extraction of the principal stress orientation, while pressure curves and overburden stress were combined to determine stress magnitude. Stress regimes were further characterized using the Aφ parameter, and only intervals demonstrating reliable fracture propagation and stable pressurization response were selected to ensure high-quality stress results. Based on this, a shallow stress profile was established, and the Coulomb failure criterion was used to compute slip tendency (Ts) to evaluate natural fracture stability.

Results

Within the 253.8–349.8 m interval in ZK1, Shmin ranges from 7.8–12.1 MPa and SHmax from 13.7–21.7 MPa, corresponding to Aφ ≈ 2–3, indicative of thrust-faulting stress. In ZK2 at depths of 129.2–471.2 m, Shmin is 5.8–9.9 MPa and SHmax is 9.7–18.2 MPa, and Aφ shows a depth-dependent transition: thrust-faulting characteristics (Aφ ≈ 2–3) above 215.3 m, strike-slip stress (Aφ ≈ 1–2) at intermediate depths, and gradual evolution toward normal-faulting stress (Aφ ≈ 0–1) at greater depths. Hydraulic fractures in both boreholes are predominantly sub-vertical, with stable maximum horizontal stress orientations of N18°W in ZK1 and N15°W in ZK2, with standard deviations of <10°. Nonetheless, shallow intervals show pronounced azimuth deflection, above ~293 m in ZK1, the deviation reaches 23°, and above ~203 m in ZK2, it reaches 29° toward the NNE, possibly suggesting fracture-induced heterogeneity weakens the rock mass, modifies local stress anisotropy, and causes reorientation of SHmax. Slip tendency calculations show Ts <0.4 throughout ZK2, indicating good fracture stability, In contrast, in ZK1, clusters within 290 ± 30 m reach Ts ≈0.6 near the frictional instability limit, accompanied by elevated SHmax relative to predicted trends, implying higher reactivation potential and mechanical risk.

Conclusions

ZK1 is dominated by thrust-faulting stress with SHmax trending ~N18°W. ZK2 exhibits a progressive transformation from thrust to strike-slip to normal-faulting stress state as depth increases, with SHmax consistently oriented between N15°W and N18°W. The shallow stress field (<500 m) is different from that of the deeper crust (>5 km), where strike-slip and normal-fault regimes dominate due to high vertical lithostatic loads, while reduced vertical stress in shallow rock favors horizontal compression and thrust-related stress. Fractures in ZK2 are stable, whereas ZK1 contains intervals with high slip potential, which require priority monitoring. [Significance] This work provides shallow in situ stress datasets for Guangdong derived from field measurements, significantly improves hydraulic fracturing interpretation reliability, offers essential mechanical parameters for near-surface engineering construction and hazard assessment, and demonstrates that shallow crust stress evolution is controlled by mechanisms distinct from those governing deeper tectonic stress fields, highlighting the scientific necessity of shallow stress measurement.

in situ stress  /  hydraulic fracturing  /  stress field  /  stress occurrence state  /  slip tendency
熊思捷, 马晓冬, 杨跃辉, 吴邦宸, 李阿伟, 孙东生. 基于水压致裂数据的浅部地应力精细化表征与分析. 地质力学学报, 2026 , 32 (2) : 414 -426 . DOI: 10.12090/j.issn.1006-6616.2025096
Sijie XIONG, Xiaodong MA, Yuehui YANG, Bangchen WU, Awei LI, Dongsheng SUN. Refined characterization and analysis of shallow crustal stresses based on hydraulic fracturing data[J]. Journal of Geomechanics, 2026 , 32 (2) : 414 -426 . DOI: 10.12090/j.issn.1006-6616.2025096
  • This research was financially supported by the Deep Earth Probe and Mineral Resources Exploration-National Science and Technology Major Project (Grant No. 2024ZD1000705).
Year 2026 volume 32 Issue 2
28
12
Cite this Article
BibTeX
Article Info
doi: 10.12090/j.issn.1006-6616.2025096
  • Receive Date:2025-07-30
  • Online Date:2026-11-17
  • Published:2026-04-28
Article Data
Affiliations
History
  • Received:2025-07-30
  • Revised:2026-01-02
  • Accepted:2026-01-06
Funding
This research was financially supported by the Deep Earth Probe and Mineral Resources Exploration-National Science and Technology Major Project (Grant No. 2024ZD1000705).
Affiliations
    1State Key Laboratory of Precision Geodesy, Hefei 230026, Anhui, China
    2School of Earth and Space Sciences, University of Science and Technology of China, Hefei 230026, Anhui, China
    3Institute of Geomechanics, Chinese Academy of Geological Sciences, Beijing 100081, China
    4Engineering Technology Innovation Center of In-situ Stress, Ministry of Natural Resources, Beijing 100081, China
References
Share
https://castjournals.cast.org.cn/joweb/dzlxxb/EN/10.12090/j.issn.1006-6616.2025096
Share to
QR

Scan QR to access full text

Cite this article
BibTeX
Citations
表12种不同金属材料的力学参数
科
Family
属数
Number of
genus
种数
Number of
species
占总种数比例
Percentage of
total species (%)
属
Genus
种数
Number of
species
占总种数比例
Percentage of total
species (%)
鹅膏菌科Amanitaceae 2 11 5.26 鹅膏菌属 Amanita 10 4.78
小菇科 Mycenaceae 2 12 5.74 丝盖伞属 Inocybe 5 2.39
多孔菌科 Polyporaceae 8 14 6.70 蜡蘑属 Laccaria 5 2.39
红菇科 Russulaceae 3 23 11.00 小皮伞属 Marasmius 6 2.87
小菇属 Mycena 11 5.26
光柄菇属 Pluteus 5 2.39
红菇属 Russula 17 8.13
栓菌属 Trametes 5 2.39
关闭全屏
  • BibTeX
  • EndNote
  • RefWorks
  • TxT