硅酸盐学报

基于计算机视觉的净浆流动扩展过程表征

PDF下载

尹锐 ¹ , 刘建忠 ¹^,² , 夏薇薇 ¹ , 申健 ¹ , 李洪文 ² , 周新文 ²

硅酸盐学报 | 水泥基材料基因与智能设计专题—研究论文 2026,54(3): 1006-1015

收起

硅酸盐学报 |水泥基材料基因与智能设计专题—研究论文 2026 , 54 (3) : 1006 -1015

基于计算机视觉的净浆流动扩展过程表征

全屏

尹锐¹, 刘建忠¹^,², 夏薇薇¹, 申健¹, 李洪文², 周新文²

作者信息

^1．重庆大学材料科学与工程学院，重庆 400044

^2．重大基础设施工程材料全国重点实验室，江苏苏博特新材料股份有限公司，南京 211103

通讯作者:

刘建忠（1976—），男，博士，研究员。

作者简介:

尹锐（1999—），男，硕士研究生。

Characterization of Cement Paste Flow Spread Process Based on Computer Vision

Rui YIN¹, Jianzhong LIU¹^,², Weiwei XIA¹, Jian SHEN¹, Hongwen LI², Xinwen ZHOU²

Affiliations

^1.School of Materials Science and Engineering, Chongqing University, Chongqing 400044, China

^2.State Key Laboratory of Engineering Materials for Major Infrastructure, Sobute New Materials Co., Ltd., Nanjing 211103, Jiangsu, China

Corresponding Author:

LIU Jianzhong (1976-), male, Ph.D., Professor. E-mail: ljz@cnjsjk.cn

YIN Rui (1999-), male, Master candidate. E-mail: 728325257@qq.com

出版时间: 2026-03-20 doi: 10.14062/j.issn.0454-5648.20250701

文章导航

摘要

收起

为解决传统水泥净浆流动扩展过程表征存在的数据处理依赖人工、操作繁琐和耗时较长等不足，提出了一种基于计算机视觉的流动扩展过程高精度表征方法。以Segment Anything Model 2（SAM2）为核心，采用You Only Look Once v11 （YOLOv11）模型确定提示点，通过透视变换与光线折射的双重几何校正方法降低误差。结果表明，计算的最终扩展度与试验结果高度一致（平均绝对误差<1 mm），同时能够获取扩展度、速率随时间变化的曲线。对这些动态过程信息的分析，有助于更加全面地表征净浆的流动行为，为反演净浆的流变性能提供了数据基础。

关键词

水泥净浆 / 流动扩展 / 动态表征 / SAM2模型 / 计算机视觉

Abstract

收起

Introduction

Rheological properties of cement paste are critical factors governing the workability of fresh concrete, significantly affecting construction performance, structural safety, and durability. Although rheometers provide direct measurements of parameters such as yield stress and plastic viscosity, their field application is often restricted by equipment costs and operational complexity. Consequently, the mini-slump flow test remains a prevalent method for evaluating workability due to its simplicity. Theoretical frameworks allow for yield stress calculation based on the final spread diameter. However, conventional analysis relies solely on the static final value, neglecting the dynamic flow process. This limitation results in a failure to capture dynamic information related to plastic viscosity, which dictates the spreading rate and flow duration. Recent computer vision technology has demonstrated a broad potential in construction materials research. Some previous studies attempted to record flow spread using cameras, they often suffered from reliance on manual data processing, insufficient precision, or requirements for expensive high-speed imaging equipment. To address these limitations, this paper was to propose a high-precision characterization method for the flow spread process of cement paste based on computer vision. This study could achieve automated, dynamic, and quantitative analysis of paste flow via integrating the You Only Look Once version 11 (YOLOv11) object detection model with the Segment Anything Model 2 (SAM2), and employing a dual geometric correction system, providing a robust data foundation for inverting rheological performance.

Methods

P·O 42.5 ordinary Portland cement, fly ash, and slag were utilized to prepare 80 groups of cement pastes with varying water-to-binder ratios (i.e., 0.45, 0.50, and 0.55) and mineral admixture dosages ranging from 0% to 50%. A polycarboxylate superplasticizer was added to regulate fluidity, creating a dataset with diverse rheological properties. The image acquisition setup consisted of a smartphone camera fixed 400 mm vertically above a 10 mm thick tempered glass plate, with an A3 paper sheet placed underneath as a spatial reference, recording videos at 1920 × 1080 resolution. The proposed characterization method followed a sequential pipeline comprising four stages, i.e., perspective correction, automated segmentation, refraction correction, and dynamic parameter calculation. First, to address trapezoidal distortion caused by oblique camera angles, a global homography matrix was calculated via detecting the four corners of the A3 reference paper in the final video frame. This matrix was applied to the entire video sequence to restore an orthogonal top-down view. Subsequently, a combined deep learning approach was employed for segmentation, where YOLOv11 detected the mold position in the initial frame to generate a "point prompt" that initializes SAM2. Leveraging its Video Object Segmentation (VOS) capability and memory mechanism, SAM2 automatically tracks and segments the paste mask throughout the sequence, effectively resolving occlusion issues where the mold or operator hands could block the paste during the initial lifting phase. Following segmentation, a refraction correction model based on Snell's law was applied to eliminate the visual displacement caused by light passing through the glass plate, establishing an accurate physical relationship between pixel width and true scale. Finally, the spread diameter D(t) and instantaneous velocity V(t) curves were extracted to quantify dynamic behavior based on the corrected masks.

Results and discussion

The experimental validation confirms the high efficacy of the proposed method in both automated segmentation and measurement accuracy. In terms of segmentation, the prompt-based mode utilizing YOLOv11 and SAM2 proves superior to the automatic mask generation mode. The model effectively propagates mask information from clear final frames back to initial frames via leveraging the VOS function, generating continuous and precise contours even when the paste is partially occluded. Regarding measurement precision, the constructed dual correction system significantly mitigates errors. The experimental results indicate thatan optical distortion causes a maximum relative error of 4.1% without a refraction correction. The application of the refractive correction model reduces this error to within 1.6%. A validation study involving 80 groups of pastes shows a linear correlation between the calculated final diameters and manual measurements, with a coefficient of determination (R²) of 0.999, a Mean Absolute Error (MAE) of 0.87 mm, and a Mean Absolute Percentage Error (MAPE) of merely 0.49%. Based on the accurate extraction of D(t) and V(t) curves, four dynamic parameters were defined, i.e., final spread diameter (D_max), peak velocity (V_max), flow stabilization time (ts_table), and time to reach peak velocity (t_V_max). Crucially, the analysis demonstrates that distinct pastes can exhibit nearly identical final diameters yet possess significantly different peak velocities and flow time. This discrepancy indicates that static measurements alone fail to capture variations in plastic viscosity and flow dynamics. The proposed dynamic indicators effectively capture these distinctions that conventional static tests fail to distinguish, offering a more comprehensive description of flow behavior.

Conclusions

This study established an automated segmentation method for cement paste via integrating YOLOv11 and SAM2, which could effectively solve the dependency on external prompts and address occlusion problems during the initial flow stage through a memory-based mask tracking mechanism. Furthermore, a dual error correction system incorporating perspective and refraction corrections was constructed to quantitatively rectify geometric and optical distortions, reducing the maximum relative measurement error from 4.1% to less than 1.6% and ensuring high fidelity of physical dimensions. Based on these foundations, a dynamic quantitative analysis method was proposed by defining key parameters such as D_max, V_max, t_stable, and t_V_max based on the dynamic curves. Compared with conventional methods, this dynamic characterization could offer improved information density and automation, achieving a more comprehensive characterization of cement paste flow behavior through quantitative analysis of the flow process. Ultimately, the method could provide a technical support for the automated and intelligent testing of cement paste workability.

Key words

cement paste / flow spread / dynamic characterization / SAM2 model / computer vision

引用本文

尹锐, 刘建忠, 夏薇薇, 申健, 李洪文, 周新文. 基于计算机视觉的净浆流动扩展过程表征. 硅酸盐学报, 2026 , 54 (3) : 1006 -1015 . DOI: 10.14062/j.issn.0454-5648.20250701

Rui YIN, Jianzhong LIU, Weiwei XIA, Jian SHEN, Hongwen LI, Xinwen ZHOU. Characterization of Cement Paste Flow Spread Process Based on Computer Vision[J]. Journal of the Chinese Ceramic Society, 2026 , 54 (3) : 1006 -1015 . DOI: 10.14062/j.issn.0454-5648.20250701

基金

收起

国家自然科学基金(52508274; U22A20229)

参考文献

收起

文献

收起

参考文献引证文献

排序方式：

2026年第54卷第3期

PDF下载

引用本文

BibTeX

文章信息

doi: 10.14062/j.issn.0454-5648.20250701

接收时间：2025-09-24
首发时间：2026-10-27
出版时间：2026-03-20

补充材料

相关文章

文章信息

作者

出版历史

收稿日期：2025-09-24
修回日期：2025-10-29

基金

国家自然科学基金(52508274; U22A20229)

作者信息

^1．重庆大学材料科学与工程学院，重庆 400044

^2．重大基础设施工程材料全国重点实验室，江苏苏博特新材料股份有限公司，南京 211103

通讯作者:

刘建忠（1976—），男，博士，研究员。

参考文献

分享链接

https://castjournals.cast.org.cn/joweb/gsyxb/CN/10.14062/j.issn.0454-5648.20250701

分享至

全文二维码

扫描看全文

引用本文

BibTeX

本文的引用情况

2种不同金属材料的力学参数

科 Family	属数 Number of genus	种数 Number of species	占总种数比例 Percentage of total species (%)	属 Genus	种数 Number of species	占总种数比例 Percentage of total species (%)
鹅膏菌科Amanitaceae	2	11	5.26	鹅膏菌属 Amanita	10	4.78
小菇科 Mycenaceae	2	12	5.74	丝盖伞属 Inocybe	5	2.39
多孔菌科 Polyporaceae	8	14	6.70	蜡蘑属 Laccaria	5	2.39
红菇科 Russulaceae	3	23	11.00	小皮伞属 Marasmius	6	2.87
				小菇属 Mycena	11	5.26
				光柄菇属 Pluteus	5	2.39
				红菇属 Russula	17	8.13
				栓菌属 Trametes	5	2.39

关闭全屏

BibTeX
EndNote
RefWorks
TxT