硅酸盐学报

纤维增强水泥基材料与不同基体间界面剪切强度及其吸水性能

PDF下载

薛善彬 ¹ , 荆蜂杰 ¹ , 王丹 ¹ , 张鹏 ¹^,² , 高小建 ³

硅酸盐学报 | 研究论文 2024,52(11): 3606-3616

收起

硅酸盐学报 |研究论文 2024 , 52 (11) : 3606 -3616

纤维增强水泥基材料与不同基体间界面剪切强度及其吸水性能

全屏

薛善彬¹, 荆蜂杰¹, 王丹¹, 张鹏¹^,², 高小建³

作者信息

^1．青岛理工大学土木工程学院，山东青岛 266525

^2．青岛理工大学，山东蓝色经济区工程建设与安全协同创新中心，山东青岛 266525

^3．哈尔滨工业大学土木工程学院，哈尔滨 150001

通讯作者:

张鹏（1981—），男，博士，教授。

作者简介:

薛善彬（1990—），男，博士，副教授。

Interfacial Shear Strength Between Fiber-Reinforced Cement-Based Materials (FRCM) and Different Substrates and Water Absorption Properties of FRCM

Shanbin XUE¹, Fengjie JING¹, Dan WANG¹, Peng ZHANG¹^,², Xiaojian GAO³

Affiliations

^1.School of Civil Engineering, Qingdao University of Technology, Qingdao 266525, Shandong, China

^2.Qingdao University of Technology, Shandong Blue Economic Zone Engineering Construction and Safety Collaborative Innovation Center, Qingdao 266525, Shandong, China

^3.School of Civil Engineering, Harbin Institute of Technology, Harbin 150001, China

Corresponding Author:

ZHANG Peng (1981-), male, Ph.D., Professor. E-mail: peng.zhang@qut.edu.cn

XUE Shanbin (1990-), male, Ph.D., Associate Professor. E-mail: xueshanbin@qut.edu.cn

出版时间: 2024-11-20 doi: 10.14062/j.issn.0454-5648.20230744

文章导航

摘要

收起

纤维增强水泥基材料具有优异的韧性和抗渗性，在劣化混凝土结构修复和破碎岩体加固工程中有着广阔的应用前景。本工作研究了聚乙烯醇（PVA）或玄武岩纤维增强水泥基材料与普通水泥砂浆、混凝土、砂岩、花岗岩间界面剪切强度的影响因素，包括纤维增强水泥基材料配合比、基体初始饱和度、基体表面切槽形式变化等。此外，通过称重法研究了与不同含水饱和度、不同类型基体粘结的纤维增强水泥基材料的毛细吸水性能。结果表明：PVA或玄武岩纤维增强水泥基材料与砂浆基体间的界面剪切强度均随基体饱和度的降低而升高；粉煤灰掺量的增加能够提高PVA纤维增强水泥基材料与砂浆间的界面剪切强度，但会降低玄武岩纤维增强水泥基材料与砂浆间的界面剪切强度。基体表面切槽数量的增加对于PVA或玄武岩纤维增强水泥基材料与基体间的界面剪切强度有提升作用，且对于PVA纤维增强水泥基材料更为显著。PVA纤维增强水泥基材料与混凝土、砂浆间的界面剪切强度高于同饱和度的砂岩与花岗岩。与干燥基体粘结的纤维增强水泥基材料的毛细吸水性系数总体略低于预湿基体；粉煤灰掺量的增加使纤维增强水泥基材料的毛细吸水系数显著提高；当粉煤灰掺量较低时，PVA纤维增强水泥基材料的毛细吸水系数显著高于玄武岩纤维增强水泥基材料。

关键词

纤维增强水泥基材料 / 界面剪切强度 / 饱和度 / 表面切槽 / 毛细吸水性能

Abstract

收起

Introduction

Fiber-Reinforced Cement-based Materials (FRCM) have excellent toughness and impermeability, and have a broad application in the repair of deteriorated concrete structures and the reinforcement of fractured rock mass. The bonding performance between the cement-based material and the substrate is affected by many factors, including the mix ratio of cement-based materials, the saturation of substrates, and the surface roughness of substrates. The initial water content of substrates affects the water exchange between substrates and fresh cement-based repair materials, further affects the water-binder ratio of repair materials, the hydration of cementitious materials and the shrinkage deformation of materials, etc., and ultimately affects the mechanical properties of the interface. Further research is needed on the effect of water saturation of different types of substrates on the interfacial bonding properties between them and FRCM with different mixing ratios. Appropriately increasing the surface roughness of old cement-based materials and rock substrates is an effective method to improve the bonding performance between them and cement-based materials. Compared with ordinary mortar, the content of fly ash and other auxiliary cementitious materials in FRCM is higher, and the toughening effect of fiber is remarkable. The bonding performance between FRCM and mortar substrates with different surface roughness is worthy of further study. Cement-based repair materials are generally poured on the surface of existing substrates, and the impermeability is crucial to the long-term effectiveness of repair and reinforcement. The water transport properties of FRCM bonded with different types of substrates with various initial water content are worthy of further study. In this work, the effects of fiber type, fly ash content, initial water saturation of substrates, and grooving form of the substrate surface on the interfacial shear strength between FRCM and ordinary cement mortar, concrete, granite, and sandstone were systematically studied through mechanical performance tests. The capillary water absorption properties of FRCM bonded to different types of substrates with different initial water saturations were studied by weighing method.

Methods

The dynamic quality monitoring method was used to control the saturation of the substrate to 0%, 50% and 100%, and an angle grinder was used to cut different forms of grooves on the surface of mortar substrates. FRCM was prepared with cement, fly ash, quartz sand, water, superplasticizer and fibers. The fiber types included PVA fiber and basalt fiber, and the fly ash content was 1.2 times and 1.8 times of the cement mass, respectively. After reaching the curing age of 28 d, three specimens were selected for interfacial shear strength test. Three 28 d old bonding composites in each group were subjected to capillary water absorption test.

Results and discussion

The increase in the saturation of the mortar substrate was not conducive to its adhesion to basalt or PVA FRCM. It's speculated that the above phenomenon was related to the water exchange between repair materials and substrates. When the substrate was dry, the water in the fresh repair material can carry cement particles to the substrate under the action of capillary suction. The water exchange across the interface was beneficial to the adhesion of repair materials to substrates, and at the same time the decrease of water-binder ratio of the repair material at the interface improved the interfacial shear strength. The increase of fly ash content enhanced the interfacial shear strength between PVA FRCM and substrates, but lead to the decrease of interfacial shear strength between basalt FRCM and substrates. Due to the pozzolanic effect and filling effect of fly ash, the increase of fly ash content in FRCM was conducive to the formation of denser microstructure, which was beneficial to its bonding with substrates. However, the improvement of fly ash on the toughness of cement-based materials can be affected by its synergistic effect with fibers. When the mechanical properties and content of fibers were low, excessive fly ash can lead to the reduction of material toughness. In the case of dry substrates, the increase of the number of grooves on the substrate surface has a more significant effect on the interfacial shear strength between PVA FRCM than that of basalt FRCM, which may be related to the excellent mechanical properties of PVA FRCM.

The increase of fly ash content can significantly improve the capillary water absorption properties of basalt or PVA FRCM bonded to mortar substrates, while the change of substrate saturation has insignificant effect on the capillary water absorption properties of basalt FRCM bonded to mortar substrates. When the mass ratio of fly ash to cement in the repair material was 1.2 and the substrate saturation was 0%, 50% and 100%, the capillary water absorption coefficient of basalt FRCM was significantly lower than that of PVA FRCM, which may be related to the higher porosity of PVA fiber.

Conclusions

The interfacial shear strength between PVA and mortar substrates, or basalt FRCM and mortar substrates decreased with the increase of substrates saturation. When the saturation of mortar substrates was constant, the increase of fly ash content enhanced the interfacial shear strength between PVA FRCM and substrates, but reduced the interfacial shear strength between basalt FRCM and substrates. The more the number of grooves on the substrate surface, the higher the interfacial shear strength between it and PVA or basalt FRCM. This phenomenon was more obvious for PVA FRCM. The effect of the grooves on the surface of dry substrates on the improvement of the interfacial shear strength between dry substrates and the basalt or PVA FRCM was more obvious than that of saturated substrate. The interfacial shear strength between PVA FRCM and concrete and sandstone substrates decreased with the increase of substrates saturation. When the substrates were dry, the interfacial shear strength between PVA FRCM and concrete was higher than that of mortar, sandstone and granite. When the substrates were partially saturated, the interfacial shear strength between PVA FRCM and concrete and mortar was equivalent or higher than that of sandstone. When the substrates were saturated, the interfacial shear strength between PVA FRCM and mortar was higher than that of concrete and sandstone. The capillary water absorption coefficient of FRCM bonded to dry mortar, concrete and sandstone substrates was generally lower than that of the same type of FRCM bonded to pre-wetted substrates. There was no significant difference in the capillary water absorption coefficient between PVA FRCM with the same mix ratio bonded to different types of substrates. The increase of fly ash content can significantly increase the capillary water absorption coefficient of FRCM bonded to substrates. When the content of fly ash was low, the capillary water absorption coefficient of PVA FRCM was significantly higher than that of basalt FRCM bonded to mortar substrate with same saturation.

Key words

fiber-reinforced cement-based materials / interface shear strength / saturation / cutting grooves on the surface / capillary water absorption properties

引用本文

薛善彬, 荆蜂杰, 王丹, 张鹏, 高小建. 纤维增强水泥基材料与不同基体间界面剪切强度及其吸水性能. 硅酸盐学报, 2024 , 52 (11) : 3606 -3616 . DOI: 10.14062/j.issn.0454-5648.20230744

Shanbin XUE, Fengjie JING, Dan WANG, Peng ZHANG, Xiaojian GAO. Interfacial Shear Strength Between Fiber-Reinforced Cement-Based Materials (FRCM) and Different Substrates and Water Absorption Properties of FRCM[J]. Journal of the Chinese Ceramic Society, 2024 , 52 (11) : 3606 -3616 . DOI: 10.14062/j.issn.0454-5648.20230744

基金

收起

国家自然科学基金(U2106220; 52008222)
国家重点研发计划(2021YFB2600704)
山东省杰出青年基金(ZR2021JQ17)

参考文献

收起

文献

收起

参考文献引证文献

排序方式：

2024年第52卷第11期

PDF下载

引用本文

BibTeX

文章信息

doi: 10.14062/j.issn.0454-5648.20230744

接收时间：2023-09-27
首发时间：2026-10-22
出版时间：2024-11-20

补充材料

相关文章

文章信息

作者

出版历史

收稿日期：2023-09-27
修回日期：2023-11-10

基金

国家自然科学基金(U2106220; 52008222)

国家重点研发计划(2021YFB2600704)

山东省杰出青年基金(ZR2021JQ17)

作者信息

^1．青岛理工大学土木工程学院，山东青岛 266525

^2．青岛理工大学，山东蓝色经济区工程建设与安全协同创新中心，山东青岛 266525

^3．哈尔滨工业大学土木工程学院，哈尔滨 150001

通讯作者:

张鹏（1981—），男，博士，教授。

参考文献

分享链接

https://castjournals.cast.org.cn/joweb/gsyxb/CN/10.14062/j.issn.0454-5648.20230744

分享至

全文二维码

扫描看全文

引用本文

BibTeX

本文的引用情况

2种不同金属材料的力学参数

科 Family	属数 Number of genus	种数 Number of species	占总种数比例 Percentage of total species (%)	属 Genus	种数 Number of species	占总种数比例 Percentage of total species (%)
鹅膏菌科Amanitaceae	2	11	5.26	鹅膏菌属 Amanita	10	4.78
小菇科 Mycenaceae	2	12	5.74	丝盖伞属 Inocybe	5	2.39
多孔菌科 Polyporaceae	8	14	6.70	蜡蘑属 Laccaria	5	2.39
红菇科 Russulaceae	3	23	11.00	小皮伞属 Marasmius	6	2.87
				小菇属 Mycena	11	5.26
				光柄菇属 Pluteus	5	2.39
				红菇属 Russula	17	8.13
				栓菌属 Trametes	5	2.39

关闭全屏

BibTeX
EndNote
RefWorks
TxT