硅酸盐学报

用于多层陶瓷电容器的抗还原BaTiO₃基介质陶瓷

PDF下载

王震 ¹^,² , 郝华 ¹^,² , 蒋松松 ¹^,² , 张洁 ² , 曹明贺 ² , 尧中华 ¹^,² , 甘小燕 ¹^,² , 刘韩星 ¹^,²

硅酸盐学报 | 第14届无机非金属材料专题研讨会专题—研究论文 2025,53(4): 808-815

收起

硅酸盐学报 |第14届无机非金属材料专题研讨会专题—研究论文 2025 , 53 (4) : 808 -815

用于多层陶瓷电容器的抗还原BaTiO₃基介质陶瓷

全屏

王震¹^,², 郝华¹^,², 蒋松松¹^,², 张洁², 曹明贺², 尧中华¹^,², 甘小燕¹^,², 刘韩星¹^,²

作者信息

^1．武汉理工大学三亚科教创新园，海南三亚 572000

^2．武汉理工大学材料科学与工程学院，材料科学与工程国际化示范学院，材料复合新技术国家重点实验室，武汉 430070

通讯作者:

郝华（1971—），女，博士，教授。

作者简介:

王震（1998—），男，博士研究生。

Anti-Reduction BaTiO₃-Based Dielectric Ceramics for Multi-Layer Ceramic Capacitors

Zhen WANG¹^,², Hua HAO¹^,², Songsong JIANG¹^,², Jie ZHANG², Minghe CAO², Zhonghua YAO¹^,², Xiaoyan GAN¹^,², Hanxing LIU¹^,²

Affiliations

^1.Sanya Science and Education Innovation Park, Wuhan University of Technology, Sanya 572000, Hainan, China

^2.School of Material Science and Engineering, International School of Material Science and Engineering, State Key Laboratory of Advanced Technology for Materials Synthesis and Processing, Wuhan University of Technology, Wuhan 430070, China

Corresponding Author:

HAO Hua (1971-), female, Ph.D., Professor. E-mail: haohua@whut.edu.cn

WANG Zhen (1998-), male, Doctoral candidate. E-mail: 1546633983@qq.com

出版时间: 2025-04-20 doi: 10.14062/j.issn.0454-5648.20240752

文章导航

摘要

收起

电子工业发展使多层陶瓷电容器的需求大增，为降低成本，适用于贱金属电极的介质陶瓷成为研究热点。选择MnO₂掺杂0.95BaTiO₃-0.05BiCoO₃陶瓷，经调整掺杂比例，其抗还原与介电性能大幅提升。结果表明：还原气氛下Mn离子变价使晶胞体积膨胀，形成不均匀结构使Curie峰分裂并展宽，介温稳定性提高，x=0.5时性能最佳，ε（25 ℃）=2354，tanδ=0.007 5，稳定性符合X8R。同时，元素变价的过程有助于降低电子浓度，电阻率提高至1.84×10¹³ Ω·cm，最大耐压达到210 kV/cm。热激励退极化漏电流测试表明Co、Mn结合氧空位形成缺陷偶极，进一步增强抗还原性能。

关键词

多层陶瓷电容器 / 钛酸钡 / 电阻率 / 缺陷偶极子 / 介电性能

Abstract

收起

Introduction

Multi-layer ceramic capacitor (MLCC) is a highly promising dielectric capacitor due to its high capacitance, favorable dielectric temperature stability, and high breakdown strength. The conventional MLCC uses expensive silver and palladium metals as inner electrode materials. In recent years, base metals such as nickel or copper are employed as inner electrodes to reduce the related costs. However, these metals must be co-fired with the dielectric layer in a reducing atmosphere. BaTiO₃ ceramics are the principal dielectric materials used in the manufacture of MLCC. The sintering of BaTiO₃ ceramics in a reducing atmosphere generates a significant number of oxygen vacancies and free electrons, which significantly impair the insulation performance and reduce the insulating properties. Also, the pronounced dielectric peak of BaTiO₃ ceramics occurs at the elevated temperature end (i.e., 125℃), leading to an inadequate temperature stability.

Recent research focus on the relaxation properties and dielectric properties of BaTiO₃-Bi(Me)O₃(Me = Fe³⁺, Co³⁺, Y³⁺, etc.) solid solutions. The co-substitution of the A and B sites via introducing cations with different ion radius and valence states is shown to disrupt the long-range ferroelectric ordering, induce diffusive phase transitions, and broaden the dielectric temperature profile. Furthermore, Zn²⁺, Mg²⁺, Mn⁴⁺, Co³⁺, and other rare-earth element ions are introduced into BaTiO₃-based ceramics as host-accepted dopants with the objective of forming defective dipoles with oxygen vacancies, which can bind the free charge movement. Among these, multivalent ions can bind electrons, thereby modifying the valence and regulating the electron concentration within the ceramics. This reduces the likelihood of conversion of Ti⁴⁺ to Ti³⁺.

In this paper, 0.95BaTiO₃-0.05BiCoO₃ dielectric ceramics were used as a matrix. A small amount of MnO₂ was selected for doping and modification, and subsequently sintered in a reducing atmosphere. The structure, micro-morphology, dielectric, and insulating properties were characterized, and the mechanism of anti-reduction was investigated.

Methods

In the preparation of the ceramics with a composition of 0.95BaTiO₃-0.05BiCoO₃-x% (in mass) MnO₂ (x=0.1, 0.2, 0.3, 0.4, and 0.5), the materials were sintered at 1275 ℃ for 2 h under a reducing atmosphere (99.5%N₂+0.5%H₂, in volume fraction), forming dense ceramic samples. Subsequently, the ceramic samples were thinned and polished, and silver paste electrodes were applied to the both sides to measure their electrical properties.

The physical structure of the samples was analyzed using a model X'Pert Pro X-ray diffractometer (XRD, PANalytical Co., the Netherlands). The microscopic morphology of the sample section was determined by a model 450 FEG field emission scanning electron microscope (FE-SEM, FEI Quanta Co., USA). The dielectric properties of the samples were measured by a model PolyK PK-CPT1705 low temperature dielectric tester. The resistivity of the ceramic samples was tested by a model Concept 80 low frequency module (Novocontrol Co., Germany). The ferroelectric properties of the samples were analyzed by a model PK-CPE1801 ferroelectric polarisation return and dielectric breakdown test system (PolyK Co., USA). The elemental valence analysis was conducted by a model 250Xi X-ray photoelectron spectrometer (XPS, EscaLab Co., USA). The thermally stimulated depolarization currents (TSDC) of the samples were carried out by a model Concept 80 TSDC (Novocontrol Co., Germany).

Results and discussion

All the ceramic samples exhibit a pseudo-cubic perovskite structure. The crystal surface spacing of the ceramics increases as the amount of MnO₂ doping increases. This indicates that Mn⁴⁺ is reduced to Mn³⁺ or Mn²⁺ during sintering in a reducing atmosphere. The radius of Mn³⁺ or Mn²⁺ is larger than that of Ti⁴⁺ (i.e., 0.060 5 nm, CN=6) ionic radius, leading to the crystal lattice distortion and increased cell volume. The cross section of the ceramics reveals fine grains (i.e., 0.24-0.32 μm), clear grain boundaries, and a close arrangement between grains. The change in valence of Mn effectively inhibits the concentration of free electrons. When x = 0.5, the insulation resistivity increases to 1.84×10¹³ Ω·cm, the breakdown voltage reaches 210 kV/cm, thus improving the anti-reduction performance of ceramics. The introduction of Mn reduces the dielectric loss of the ceramics and improves their dielectric temperature stability. The optimum dielectric properties are achieved when x = 0.5 (i.e., a dielectric constant of 2354, a dielectric loss of 0.0075, and ΔC/C(25℃)≤±15% at -55 to 154 ℃). The XPS spectra reveal the presence of both divalent and trivalent Co ions in the ceramics. The result of TSDC test shows a TSDC peak associated with trapped charge, which is related to the change in valence states of the variable valency acceptor ions Co and Mn. Two TSDC peaks are also related to defect dipoles, which are formed by Co and Mn with oxygen vacancies in the ceramic sample.

Conclusions

The effect of MnO₂ doping on the phase structure, microstructure, and electrical properties of 0.95BT-0.05BC ceramics was investigated. The results demonstrated that Mn⁴⁺ ions underwent a conversion to Mn³⁺ or Mn²⁺ ions during sintering process in a reducing atmosphere, having the larger ionic radius. This transformation led to an expansion of the cell volume. Mn doping significantly impacted the broadening of the Curie peak and enhanced the dielectric temperature stability of 0.95BT-0.05BC ceramics. Specifically, as x = 0.5, the dielectric constant at 25 ℃ was 2354, and the dielectric loss was 0.007 5. Furthermore, at -55 to 154 ℃, ΔC/C(25℃) ≤ ±15%. The resistivity at room temperature increased to 1.84×10¹³ Ω·cm, and the breakdown voltage increased to 210 kV/cm. The XPS spectra revealed the presence of both divalent and trivalent Co ions in the ceramic, indicating that Co ions could capture free electrons and reduce their valence state. The result of TSDC test further demonstrated the existence of two types of defective dipoles, which were associated with the acceptor substitution of Co and Mn. The combination of these two factors reduced the carrier concentration in the ceramics, thereby hindering the migration of oxygen vacancies and free electrons and improving the anti-reduction performance.

Key words

multi-layer ceramic capacitor / barium titanate / resistivity / defect dipole / dielectric property

引用本文

王震, 郝华, 蒋松松, 张洁, 曹明贺, 尧中华, 甘小燕, 刘韩星. 用于多层陶瓷电容器的抗还原BaTiO₃基介质陶瓷. 硅酸盐学报, 2025 , 53 (4) : 808 -815 . DOI: 10.14062/j.issn.0454-5648.20240752

Zhen WANG, Hua HAO, Songsong JIANG, Jie ZHANG, Minghe CAO, Zhonghua YAO, Xiaoyan GAN, Hanxing LIU. Anti-Reduction BaTiO₃-Based Dielectric Ceramics for Multi-Layer Ceramic Capacitors[J]. Journal of the Chinese Ceramic Society, 2025 , 53 (4) : 808 -815 . DOI: 10.14062/j.issn.0454-5648.20240752

基金

收起

国家重点研发计划项目(2023YFB3812200)
国家自然科学基金(52472135)
广东省基础与应用基础研究基金区域联合基金重点项目(2022B1515120041)

参考文献

收起

文献

收起

参考文献引证文献

排序方式：

2025年第53卷第4期

PDF下载

引用本文

BibTeX

文章信息

doi: 10.14062/j.issn.0454-5648.20240752

接收时间：2024-11-28
首发时间：2026-10-22
出版时间：2025-04-20

补充材料

相关文章

文章信息

作者

出版历史

收稿日期：2024-11-28
修回日期：2024-12-10

基金

国家重点研发计划项目(2023YFB3812200)

国家自然科学基金(52472135)

广东省基础与应用基础研究基金区域联合基金重点项目(2022B1515120041)

作者信息

^1．武汉理工大学三亚科教创新园，海南三亚 572000

^2．武汉理工大学材料科学与工程学院，材料科学与工程国际化示范学院，材料复合新技术国家重点实验室，武汉 430070

通讯作者:

郝华（1971—），女，博士，教授。

参考文献

分享链接

https://castjournals.cast.org.cn/joweb/gsyxb/CN/10.14062/j.issn.0454-5648.20240752

分享至

全文二维码

扫描看全文

引用本文

BibTeX

本文的引用情况

2种不同金属材料的力学参数

科 Family	属数 Number of genus	种数 Number of species	占总种数比例 Percentage of total species (%)	属 Genus	种数 Number of species	占总种数比例 Percentage of total species (%)
鹅膏菌科Amanitaceae	2	11	5.26	鹅膏菌属 Amanita	10	4.78
小菇科 Mycenaceae	2	12	5.74	丝盖伞属 Inocybe	5	2.39
多孔菌科 Polyporaceae	8	14	6.70	蜡蘑属 Laccaria	5	2.39
红菇科 Russulaceae	3	23	11.00	小皮伞属 Marasmius	6	2.87
				小菇属 Mycena	11	5.26
				光柄菇属 Pluteus	5	2.39
				红菇属 Russula	17	8.13
				栓菌属 Trametes	5	2.39

关闭全屏

BibTeX
EndNote
RefWorks
TxT