硅酸盐学报

基于粉煤灰高效催化的莫来石多孔陶瓷孔结构构筑与分离性能

PDF下载

付锦绣 ¹ , 马玉婷 ¹ , 孟庆博 ² , 付千龙 ¹ , 王娟 ¹ , 李双 ¹

硅酸盐学报 | 研究论文 2024,52(9): 2969-2980

收起

硅酸盐学报 |研究论文 2024 , 52 (9) : 2969 -2980

基于粉煤灰高效催化的莫来石多孔陶瓷孔结构构筑与分离性能

全屏

付锦绣¹, 马玉婷¹, 孟庆博², 付千龙¹, 王娟¹, 李双¹

作者信息

^1．山东理工大学资源与环境工程学院，山东淄博 255049

^2．山东建研检测检验科技有限公司，济南 250031

通讯作者:

李双（1981—），男，博士，副教授。

作者简介:

付锦绣（1997—），女，硕士研究生。

Construction and Filtration Performance of Mullite Fibrous Porous Ceramics by in-situ Catalysis of Fly Ash

Jinxiu FU¹, Yuting MA¹, Qingbo MENG², Qianlong FU¹, Juan WANG¹, Shuang LI¹

Affiliations

^1.School of Resources and Environmental Engineering, Shandong University of Technology, Zibo 255049, Shandong, China

^2.Shandong Jianyan Testing and Inspection Technology Co., Ltd., Jinan, 255031, China

Corresponding Author:

LI Shuang (1981-), male, Ph.D., Associated Professor E-mail: lishuang@sdut.edu.cn

FU Jinxiu (1997-), female, Master candidate. E-mail: Fujinxiu2021@163.com

出版时间: 2024-09-20 doi: 10.14062/j.issn.0454-5648.20240052

文章导航

摘要

收起

随着碳减排政策的实施和水处理标准的提升，多孔陶瓷在水处理中的应用受到越来越广泛的关注。传统的多孔陶瓷材料受到原料来源、制备能耗等方面的限制，在水处理行业的规模化应用受到极大限制，因此开发低制备成本、高渗透通量的多孔陶瓷成为亟待解决的问题。本文以粉煤灰为主要材料、氟化铝（AlF₃）为催化剂，制备了高孔隙率、高通量莫来石多孔陶瓷，研究了AlF₃催化莫来石晶须的形成机理及莫来石多孔陶瓷孔结构构筑过程。随着莫来石晶须的生长，1200 ℃烧结多孔陶瓷的孔隙率从56.4%增加到57.6%，平均孔径从0.75 μm增加到1.24 μm。考察了莫来石多孔陶瓷在乳化液处理中的选择渗透性，当跨膜压力低于0.25 bar时其截留率率超过90.2%。

关键词

多孔陶瓷 / 孔隙率 / 粉煤灰 / 烧结 / 莫来石晶须

Abstract

收起

Introduction

Porous ceramics are-widely used in a variety of environmental fields such as solid-liquid separation and hot gas filtration due to their high mechanical strength, excellent chemical resistance, and high thermal stability. Conventional porous ceramics are usually made of particle-packing of inorganic powders, which are usually characterized by a low porosity, a high self-weight, a low permeability and a high filtration resistance. It is thus necessary to develop novel porous ceramics with a high porosity, a high mechanical strength and a low packing density. Mullite whisker-based porous ceramics have attracted recent attention in the treatment of various wastewaters. Compared with porous ceramics prepared by conventional particle-packing, mullite whisker-based porous ceramics are constructed by whisker interlocking, resulting in fibrous structures with a high porosity, a high pore connectivity and a low packing density. However, these mullite porous ceramics are seldom used in industry due to the high cost of the high-purity starting materials. Fly ash is a major by-product of coal combustion. The elemental analysis shows that fly ash is mainly composed of unburned carbon, metal oxides (i.e., Si, Al, and Fe) and other inorganic materials. Fly ash can be used to prepare mullite porous ceramics due to the presence the high content of aluminum silicates. However, the effect of holding time on the growth of mullite whiskers and the permeance-selectivity of the fibrous structures is still unclear. In order to elucidate the growth mechanism of mullite whiskers based on gas-solid reaction, the effects of sintering temperature and holding time on the microstructure, phase composition and filtration properties of the porous ceramics were investigated.

Methods

Fly ash powder provided by Huaneng Thermal Power Plant in Zibo, China, and Al(OH)₃ purchased from Sinopharm Chemical Reagent Co. Ltd., China, were used as major materials. AlF₃·3H₂O purchased from Sinopharm Chemical Reagent Co. Ltd., China, was employed as a catalyst for mullite whisker growth. In order to prepare porous ceramics with a high fracture strength, sodium carboxymethyl cellulose (CMC) from Sinopharm Chemical Reagent Co., China was chosen as a binder. Fly ash, Al(OH)₃, AlF₃·3H₂O and CMC were mixed and ground in a ball mill, and then the slurry was dried with a rotary evaporator and sieved through a stainless steel sieve to obtain a homogeneous mixture. After dry pressing, the green body was sintered in a muffle furnace. The effect of holding time on the formation and growth of mullite whiskers was elucidated at different holding time (i.e., 2, 4 h and 6 h). The microstructure of the porous ceramics was determined by scanning electron microscopy (SEM). The phase composition of the porous ceramics was analyzed by X-ray diffraction (XRD). The selectivity of the porous ceramics was investigated by oil-in-water emulsion separation experiments.

Results and discussion

To clarify the growing mechanism of mullite whiskers based on solid-vapor reaction, the influences of sintering temperature and holding time on the microstructure, phase composition and filtration performance of the porous ceramics are investigated. The gas AlF₃·3H₂O acts as a catalyst for the formation and growth of mullite whiskers. The thermogravimetric analysis curves indicate that the mullite whisker growth follows a gas-solid reaction mechanism, where AlF₃·3H₂O acts as a catalyst for the formation and growth of mullite whisker. The mass loss of the samples sintered at different temperatures is similar while the shrinkage increases from 2.0% to 4.2% as the holding time increases. A liquid phase formed during the sintering process enhances the particles rearrangement, the mass diffusion and migration, and the densification of the specimens. The XRD patterns indicate that a high sintering temperature and a long holding time were favorable for the formation of the mullite phase. The whisker aspect ratio is related to the sintering temperature and the concentration of the atmosphere provided by the additives. The analysis of the length-to-diameter ratio of the mullite whiskers reveals that the increase in holding time favors the growth of mullite whiskers. Based on the analysis of the pore structure of the porous ceramics, the sintering temperature is a key factor affecting the porosity, water absorption and pore size of the porous ceramics, while the holding time has a slight effect. According to the results of flux tests on the specimens sintered at 1 200 ℃ for 6 h, the permeation flux decreases from 210.61 L/(m²·h) to 192.35 L/(m²·h). When the trans-membrane pressure increases from 0.1 bar to 0.4 bar, the oil rejection of the porous ceramic reaches 90%.

Conclusions

The sintering temperature affected shrinkage of the porous ceramics. For the specimen sintered at 1 100 ℃, only a slight shrinkage of approximately 0.2% occurred during sintering. For the specimen sintered at 1 200 ℃, the shrinkage increased from 2.0% to 4.2% due to the formation of silica-rich liquid phase. Also, the high sintering temperature favored the formation of mullite phase. The growth of mullite whiskers increased both in porosity and pore size of the whisker-constructed porous ceramics. With the growth of mullite whiskers, the porosity of the porous ceramics increased from 56.4% to 57.6% for the specimen sintered at 1 200 ℃, and the average pore size increased from 0.75 to 1.24 μm. The emulsion test indicated that the permeate flux decreased from 210.61 to 192.35 L/(m²·h) for the specimen sintered at 1 200 ℃. Oil rejection of the porous ceramics decreased from appropriately 90% to 87% as TPM increased from 0.1 to 0.4 bar.

Key words

porous ceramics / porosity / fly ash / sintering / mullite whisker

引用本文

付锦绣, 马玉婷, 孟庆博, 付千龙, 王娟, 李双. 基于粉煤灰高效催化的莫来石多孔陶瓷孔结构构筑与分离性能. 硅酸盐学报, 2024 , 52 (9) : 2969 -2980 . DOI: 10.14062/j.issn.0454-5648.20240052

Jinxiu FU, Yuting MA, Qingbo MENG, Qianlong FU, Juan WANG, Shuang LI. Construction and Filtration Performance of Mullite Fibrous Porous Ceramics by in-situ Catalysis of Fly Ash[J]. Journal of the Chinese Ceramic Society, 2024 , 52 (9) : 2969 -2980 . DOI: 10.14062/j.issn.0454-5648.20240052

基金

收起

山东省自然科学基金(ZR2020MEM027)
国家自然科学基金(52002364)

参考文献

收起

文献

收起

参考文献引证文献

排序方式：

2024年第52卷第9期

PDF下载

引用本文

BibTeX

文章信息

doi: 10.14062/j.issn.0454-5648.20240052

接收时间：2024-01-21
首发时间：2026-10-22
出版时间：2024-09-20

补充材料

相关文章

文章信息

作者

出版历史

收稿日期：2024-01-21
修回日期：2024-02-15

基金

山东省自然科学基金(ZR2020MEM027)

国家自然科学基金(52002364)

作者信息

^1．山东理工大学资源与环境工程学院，山东淄博 255049

^2．山东建研检测检验科技有限公司，济南 250031

通讯作者:

李双（1981—），男，博士，副教授。

参考文献

分享链接

https://castjournals.cast.org.cn/joweb/gsyxb/CN/10.14062/j.issn.0454-5648.20240052

分享至

全文二维码

扫描看全文

引用本文

BibTeX

本文的引用情况

2种不同金属材料的力学参数

科 Family	属数 Number of genus	种数 Number of species	占总种数比例 Percentage of total species (%)	属 Genus	种数 Number of species	占总种数比例 Percentage of total species (%)
鹅膏菌科Amanitaceae	2	11	5.26	鹅膏菌属 Amanita	10	4.78
小菇科 Mycenaceae	2	12	5.74	丝盖伞属 Inocybe	5	2.39
多孔菌科 Polyporaceae	8	14	6.70	蜡蘑属 Laccaria	5	2.39
红菇科 Russulaceae	3	23	11.00	小皮伞属 Marasmius	6	2.87
				小菇属 Mycena	11	5.26
				光柄菇属 Pluteus	5	2.39
				红菇属 Russula	17	8.13
				栓菌属 Trametes	5	2.39

关闭全屏

BibTeX
EndNote
RefWorks
TxT