硅酸盐学报

光固化3D打印钇铝石榴石透明陶瓷及其微结构调控

PDF下载

胡松 ¹^,³ , 唐雨馨 ¹^,²^,³ , 周国红 ¹^,³ , 王士维 ¹^,³

硅酸盐学报 | 研究论文 2024,52(3): 882-889

收起

硅酸盐学报 |研究论文 2024 , 52 (3) : 882 -889

光固化3D打印钇铝石榴石透明陶瓷及其微结构调控

全屏

胡松¹^,³, 唐雨馨¹^,²^,³, 周国红¹^,³, 王士维¹^,³

作者信息

^1．中国科学院上海硅酸盐研究所，高性能陶瓷和超微结构国家重点实验室，上海 201899

^2．中国科学院大学材料科学与光电技术学院，北京，100049

^3．中国科学院大学，北京 100049

作者简介:

胡松（1989—），男，博士，副研究员。

Digital Light Processing 3D Printing of Y₃Al₅O₁₂ Transparent Ceramics and Microstructure Regulation

Song HU¹^,³, Yuxin TANG¹^,²^,³, Guohong ZHOU¹^,³, Shiwei WANG¹^,³

Affiliations

^1.State Key Laboratory of High Performance Ceramics and Superfine Microstructure, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 201899, China

^2.Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China

^3.University of Chinese Academy of Sciences, Beijing 100049, China

HU Song (1989—), male, PhD, Associate Professor. E-mail: yzhusong10@mail.sic.ac.cn

出版时间: 2024-03-20 doi: 10.14062/j.issn.0454-5648.20230673

文章导航

摘要

收起

成型是钇铝石榴石（YAG）透明陶瓷研制的关键环节，对透明陶瓷的致密化过程及其力学、热学和光学性能有重要影响。本工作围绕YAG透明陶瓷的基于数字光处理（DLP）技术的光固化3D打印成型，系统地开展了YAG陶瓷浆料的研制、陶瓷生坯的构筑及坯体脱脂和烧结工艺研究。采用流变仪分析了固含量对陶瓷浆料流变特性的影响，借助分析曝光参数对单层陶瓷膜特性的影响，确立了最佳的光固化工艺参数。结合TG-DTA分析，对陶瓷坯体脱脂制度进行了精准控制。采用真空高温烧结工艺制备得到高致密YAG透明陶瓷，讨论了固含量、烧结温度等工艺参数对YAG透明陶瓷微结构演变及光学质量的影响，基于DLP光固化成型技术成功制备出可见光透过率高达82.9%的高性能YAG透明陶瓷。

关键词

3D打印 / 钇铝石榴石 / 透明陶瓷 / 微结构调控

Abstract

收起

Introduction

: Molding process is recognized as one of the most critical procedures in the preparation of Y₃Al₅O₁₂ (YAG) transparent ceramics, affecting directly the densification of YAG transparent ceramics as well as their mechanical, thermal and optical properties. Various molding processes (i.e., cold isostatic pressing, slip casting, tap casting, and gel-casting) are applied to fabricate YAG transparent ceramics. However, the emergence of designing philosophy and applying technology promotes brand-new requirements on configurations or hybrid-functions of transparent ceramics. It is more difficult to realize the integrated molding of those transparent ceramics via traditional molding processes. Digital light processing (DLP) based 3D printing technology is a developed technology for ceramic forming. Some ceramic parts with complex shapes, high accuracy on sizes and high surface qualities can be obtained by this technology. The ceramic materials with a high performance are fabricated in recent years. Nevertheless, little work on YAG transparent ceramics have been reported yet. This paper dealt with DLP 3D printing of YAG transparent ceramics, and investigated the slurry preparation, molding, degreasing and sintering processes of the ceramics.

Materials and method

Commercial alumina (purity: 99.99%) and yttrium oxide (purity: 99.99%) powders with a small fraction of sintering additives (i.e., TEOS and MgO) were weighed stoichiometrically and mixed thoroughly in ethanol by ball-milling. The slurry was dried at 60 ℃ for 24 h, ground and sieved through a 200-mesh screen, subsequently calcined at 800 ℃ to obtain a homogenously distributed sub-micron-sized Al₂O₃-Y₂O₃ powder. The ceramic slurries with different solid loadings suitable for DLP 3D printing were prepared via mixing the mixed powder with photocurable resin, photoinitiator and defoamer. The green bodies with layers (layer thickness of 50 μm) were fabricated based on a computer-aided designed model in a model ADMAFLEX 130 instrument (ADMATEC Europe BV., the Netherlands). Afterwards, the green bodies were heat-treated in a muffle furnace at 600 ℃ for 5 h to eliminate organic components and further densified by sintering in vacuum at high temperatures. The specimens were double-surface polished to 1 mm for the coming characterizations.

The rheological properties of the photocurable ceramic slurries were characterized by a model MCR302 stress-controlled rotational rheometer (Anton Par GmbH, Austria) with a cone (the diameter of 20 mm). The curing depth was determined via collecting the thickness of three independent printed samples. The thermal properties of the green body were determined in air by thermogravimetry (TG) and differential scanning calorimetry in a model STA449C thermal analyzer (NETZSCH Co., Germany) at a heating rate of 10 ℃/min. The microstructures of the powders, biscuits, and sintered YAG transparent ceramics were measured by a model SU8220 field emission-scanning electron microscope (FE-SEM) and a model TM3000 scanning electron microscope (SEM). The in-line transmittances of the ceramics were examined by a model V-770 UV-Vis-NIR spectrophotometer.

Results and discussion

The influence of solid loading on the rheological properties of the photocurable slurries was investigated by a stress-controlled rotational rheometer. The viscosity of the ceramic slurry increases from 7.9 to 11.7 Pa·s at 32 s^-1 as the solid loading increases from 39.5% to 42.0%. The viscosities are suitable for the spreading of the slurries on the PET film. However, further increasing the solid loading probably leads to an increase of the viscosity and the slurry cannot spread out fluently. Thus, the ceramic slurries with solid loadings from 39.5% to 42.0% are prepared. The influence of photo-curing parameters on the curing depth, accuracy and strength of the single-layer ceramic was analyzed. The proper curing parameter is 50 mW/cm²-3 s. According to the TG-DTA analysis, the degreasing procedure is precisely controlled. Especially, a low temperature rising rate of 0.3 ℃/min is set at 300-520 ℃. The degreasing process is accomplished after holding at 600 ℃ for 5 h to remove all organic components. Little defects such as layer-layer separation and inner-layer cracks appear due to the microstructure. A vacuum sintering method is applied to further densify the ceramic. The YAG transparent ceramic with a high in-line transmittance of 82.9% is finally obtained by DLP 3D printing technology. This work can provide a foundation for the applications of YAG transparent ceramics.

Conclusions

Ceramic slurries with different solid loadings suitable for DLP 3D printing were prepared with a mixed Al₂O₃-Y₂O₃ powder. The influence of photo-curing parameters on the green bodies was discussed. The ceramic slices with superior comprehensive properties (i.e., curing depth, accuracy and strength) were obtained at the curing parameter of 50 mW/cm²-3 s. This processing parameter was used to print the green bodies of YAG transparent ceramics. According to the results by TG-DTA, degreasing processing was decided, and a low temperature rising rate of 0.3 ℃/min was set at 300-520 ℃, due to the integrity of microstructures of the ceramic biscuits. YAG transparent ceramics with a high optical quality were obtained via high temperature sintering in vacuum. Increasing the solid loading and the sintering temperature favored the mass transfer process. The YAG transparent ceramic with a high in-line transmittance of 82.9%@600 nm was finally obtained with the slurry with 42% solid loading at 1 780 ℃ for 3 h.

Key words

3D printing / yttrium aluminum garnet / transparent ceramics / microstructure regulation

引用本文

胡松, 唐雨馨, 周国红, 王士维. 光固化3D打印钇铝石榴石透明陶瓷及其微结构调控. 硅酸盐学报, 2024 , 52 (3) : 882 -889 . DOI: 10.14062/j.issn.0454-5648.20230673

Song HU, Yuxin TANG, Guohong ZHOU, Shiwei WANG. Digital Light Processing 3D Printing of Y₃Al₅O₁₂ Transparent Ceramics and Microstructure Regulation[J]. Journal of the Chinese Ceramic Society, 2024 , 52 (3) : 882 -889 . DOI: 10.14062/j.issn.0454-5648.20230673

基金

收起

国家自然科学基金项目(52372072)

参考文献

收起

文献

收起

参考文献引证文献

排序方式：

2024年第52卷第3期

PDF下载

引用本文

BibTeX

文章信息

doi: 10.14062/j.issn.0454-5648.20230673

接收时间：2023-08-31
首发时间：2026-10-22
出版时间：2024-03-20

补充材料

相关文章

文章信息

作者

出版历史

收稿日期：2023-08-31
修回日期：2023-08-31

基金

国家自然科学基金项目(52372072)

作者信息

^1．中国科学院上海硅酸盐研究所，高性能陶瓷和超微结构国家重点实验室，上海 201899

^2．中国科学院大学材料科学与光电技术学院，北京，100049

^3．中国科学院大学，北京 100049

参考文献

分享链接

https://castjournals.cast.org.cn/joweb/gsyxb/CN/10.14062/j.issn.0454-5648.20230673

分享至

全文二维码

扫描看全文

引用本文

BibTeX

本文的引用情况

2种不同金属材料的力学参数

科 Family	属数 Number of genus	种数 Number of species	占总种数比例 Percentage of total species (%)	属 Genus	种数 Number of species	占总种数比例 Percentage of total species (%)
鹅膏菌科Amanitaceae	2	11	5.26	鹅膏菌属 Amanita	10	4.78
小菇科 Mycenaceae	2	12	5.74	丝盖伞属 Inocybe	5	2.39
多孔菌科 Polyporaceae	8	14	6.70	蜡蘑属 Laccaria	5	2.39
红菇科 Russulaceae	3	23	11.00	小皮伞属 Marasmius	6	2.87
				小菇属 Mycena	11	5.26
				光柄菇属 Pluteus	5	2.39
				红菇属 Russula	17	8.13
				栓菌属 Trametes	5	2.39

关闭全屏

BibTeX
EndNote
RefWorks
TxT